Question about 2004 Dodge Ram

1 Answer

Chang rear brake light

I can get the screws next to the tailgate, but there seems to be a third screw on the other side which i can not get to.

Posted by on

  • dtmusec Jun 23, 2009

    this solved my problem. I fixed it!!!

    Thanks much



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 60 Answers

It's just a ridged clip. just pull really hard but carefully. Sometimes it needs to be pryed very gently and I do mean carefully or you will crack the edge of the light

Posted on Jun 21, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I replace the brake light bulb

1.Open the tailgate.
2. Locate the plastic plugs attached to the brake light housing (on the right side of the driver side light, on the left of the passenger side).
3. Carefully pry up the plugs with a screwdriver or other flat tool (I believe there are two).
4. The light should be free to pull out (pull toward the rear of the vehicle). You should see two torx screws.
5. Remove the bolts and pull the housing away from the tail light lens.
6. Twist and pull to remove the correct bulb.
7. Insert the new bulb into the holder and replace the housing.
8. Verify that the replacement bulb(s) are working.
9. Reinstall the torx screws and place the assembly back into it proper location on the vehicle.
10. Push the plugs back into the holes and verify that it is secure.
11. Close the tailgate and check for proper fitment.

May 12, 2014 | 2011 Dodge Nitro Heat


How to replace the brake light on a 2003 honda pilot ?

There are two philips head screws that are only accessible after opening the rear tailgate lid. Remove the two screws which will allow the removal of the entire tail-light assembly. (Note that it might take some effort as there are two retaining lugs on the outer edge of the fixture which are press fitted but wiggle and pull and they will pop loose, just be careful.) The lights are identified tail and brake. A third turn to the left and the bulb housing can be removed. Simply pull the bulb from the plug and replace with like bulb bought at any auto parts store. NOTE : what ever you do .Do it carefully and slowly. Thanks.this will help.

on Mar 08, 2010 | Honda Pilot Cars & Trucks

1 Answer

Replace rear brake light 2007 jeep liberty

Open tailgate and use a #20 Torx screwdriver to remove two screws located on the inner side tail light assembly. On the driver's side, the screws are accessable through the tailgate hinge area with the gate open.Pull taillight assembly straight back from the vehicle to get it off. You may need to utilize a wedge to gently work the top and bottom of assembly away from vehicle on outer side. If so, be careful to use plastic wedge or a protective layer (such as a thin piece of cardboard) next to the body to prevent scratching the paint.Once removed, twist applicable light cover counter clockwise and pull to access lightbulb.You may want to apply a small amount of lithium grease to the two plastic stud holes before reinstalling the cover to make it easier to remove the next time.

Mar 05, 2011 | 2007 Jeep Liberty Sport

1 Answer

How to replace the rear hatch brake light on a 2001 dodge grand caravan

If you are referring to the Third Brake Light mounted at the top of the rear hatch, then there should be 2 screws on either side of the lense. Remove those two screws and pull the lense off. You can now twist the bulb socket counter-clockwise and remove it from the lense.

Jan 21, 2011 | 2001 Dodge Grand Caravan

1 Answer

Replace rear wiper motor

In taking the rear wiper arm off, it seems to corrode onto the motor drive hub or axle. Shooting some lubricant as best you can into the area and work the arm with the clip up as best you can, it will eventually work itself off. Lift the tailgate and start at the top plastic pieces, they just pull off, followed by the sides. When you get to the main plastic pane, remove the screws in the handle lift and bottom screws. I f you have courtesy lights, pop them out and disconnect. If you have a rear brake light, remove that cover as well. Once all screws are removed, that panel will just pull off as well. With that removed, the wiper motor is visible, and three screws and the wiring are all that needs to be removed.
The rear wiper can also be removed by drilling a 3/16 hole in the center where it attaches and use a faucet handle puller, it will pull it right off. you can fill the hole with epoxy putty or spot putty after reinstalling it.

try this but be careful..

Nov 28, 2010 | 1993 Dodge Caravan

1 Answer

How do you get the brake light bulb out of the its holder?

Welcome to


3157 Brake light

How to Remove bulb:

Remove the Lamp unit from the end of the quarter panel.

"Open tailgate to access and remove the two screws that secure the inboard side of the rear lamp unit to the side of the tailgate. (see Figure) Pull the outboard side of the rear lamp unit rearward (away from the end of the quarter panel) far enough to unsnap the two ball studs on the outboard side of the lamp housing from the plastic nuts in the quarter panel."

Change Bulb:

See Figure

Regards, Lee Davidian

Thank you for using

Nov 05, 2010 | 2002 Jeep Liberty

2 Answers

How do I access a rear brake light bulb to replace it on a 1998 Ford explorer

you have to remove the taillamp assembly. there should be 2 screws(possibly torx heads)on the side when you open the hatch,remove those screws and pull the taillight out-the just unscrew the bulb

Feb 17, 2010 | 1998 Ford Explorer

1 Answer

How to replace and change the third brake light (

there should be a screw on either side of the black plastic case, after that it is simple

Aug 12, 2009 | 2004 Nissan Armada

3 Answers

I need to change the brakelight on my 2001 gmc sierra?

Which Brake line are we Talking about. The one from the Master Cylinder or one from a Caliper on??????????

Jan 23, 2009 | 2001 GMC Sierra Crew Cab

2 Answers

Rear blinker light change 2001 ram1500

Welcome to FY
open the tale gate look at the side where the light is there is 2 screw that hold the light to the box

Jan 10, 2009 | 2001 Dodge Ram 1500 Truck 2WD

Not finding what you are looking for?
2004 Dodge Ram Logo

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides