Question about 2001 Dodge Ram 2500 Truck

1 Answer

HOW TO REMOVE POWER STEERING PULLY FROM 1996 DODGE RAM 2500 iT HAS A ALLEN HEAD IN IT BUT WHEN TURNED DOES NOT SEEM TO LOOSEN THE PULLEY

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 721 Answers

You need a power steering pulley puller set. The Allen means nothing. It's part of the shaft & is used only for factory installation.

Posted on Jun 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i get the A/C belt off of my 1996 caravan


If it is a 3.0 engine, you should have an idler pulley you have to loosen to remove the belt. You loosen the bolt in the pulley then turn the adjusting bolt.

Jan 18, 2013 | 1996 Dodge Caravan

1 Answer

Power steering pump pully on 01 dodge ram


You will need a power steering pump pulley puller. Check with your local parts store to see if they rent or sell one.

Jan 08, 2012 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

How do I loosen the tension pulley on the serpentine belt to remove the alternator?


mabpest_11.gif
tensioner is pully just below the filler cap for the power steering..use 15mm socket breaker bar and pull clockwise to release tension

Jan 31, 2011 | 1998 Dodge Grand Caravan

1 Answer

Where do i start how to install timing belt on a 2000 2.4 hyundai sonata


First remove all. Power-steering pump 3 bolts on cylinder head. Loosen the alternator. remove the two belts. Underneath the car. remove black wheel arch plastic cover (6 or 7screws) Loosen the air con pump tension-er pully. Remove belt. put a trolley jack under engine as the mounting needs to be removed and lift the engine slightly. Remove the engine mounting bolts next to the black cam belt cover and remove the mounting. Loosen the Main crank shaft pulley. Normally very tight put a power bar and socket on. engine turns forward so let the bar rest on X member and turn the key only so that the engine turns. do not start. Remove cam belt covers (comes in to parts - top and bottom) then loosen the tension pulley which is on the left. 1 x bolt in middle. remove cam belt. now the tricky part. Replace the bottom crack pulley. turn so that the marks are lining up. the cam pulley has got a small hole in turn the hole upward to the top of engine. there is a small dot on the cylinder head which can be seen through the hoe. line up. replace idle pulley on the right. replace tension pulley on the left. put new belt on and now to tension the belt. take a number 5 or 6 allen key and turn the tension er clock wise until its like a watch at 10 min to the hour. tighten the bolt. test belt with fingers. if belt to loose you will feel the belt move easily. belt must not be to hard when pressed. try to turn the belt with fingers half a turn if going passed the halfway mark tighten some more. Use power bar and ensure engine turns properly meaning two or three full turns with hands without it getting stuck. otherwise the valve and piston is toughing. if so do crank turn of 180 degrease. free turn again. should be right. replace all that was taken off. start car. if belt tension is to tight you will hear a signing sound.

Aug 04, 2010 | 2001 Hyundai Sonata

1 Answer

2001 Dodge Intrepid Serpantine


Loosen the tensioner pulley adjusting bolt under the power steering pump.

May 23, 2009 | 2001 Dodge Intrepid

1 Answer

Hoe to Replace an alternator on a 1996 Dodge Ram Van 2500 3.9L V6


Remove negative battery cable.
Remove the electrical plug and wireing. Mark them.
Loosen the alternator pivot bolt.
Remove the bolt that attaches the alternator to the adjustment arm.
Rotate the alternator to loosen the drive belt and disengage the belt from the pulley. Be careful that any spacers that are used in mounting are kept with their original bolts. This will make correct reinstallation much easier.
While supporting the alternator remove the pivot bolt.
Remove the alternator from the vehicle.
Do the reverse procedure to install new alternator.

Feb 02, 2009 | 2000 Dodge Caravan

2 Answers

On 98 intrigue water pump removal how do i clear the ps pully


Im not sure what engine you have since this information was not provided. But the Power Steering Pump pulley usually has some 'holes' on the pulley in which you can get a wrench through to loosen and remove the bolt.

Dec 29, 2008 | 1998 Oldsmobile Intrigue

1 Answer

How do you replace the ''multi-function'' switch on 2nd gen Ram?


Hi my name is Allen!

To replace the switch first remove the rubber handle for the tilt wheel by pulling it straight toward the steering wheel, because there is a torks head screw under it. Next remove the two torks head screws on the bottom of the cover. Next remove the rubber cover for the shifter and slide it out of the way. Next take the two screws out of the switch and remove it. I'm assuming you are talking about the swich on the steering column.

For further asistance you may reach me at FixYa!

Dec 24, 2008 | 2005 Dodge Ram 2500 Truck

1 Answer

Power steering pump 1500 3.9 p/u


You'll need a power steering pulley puller available from many different tool manufacturers.

Oct 18, 2008 | 2002 Dodge Ram Maxi

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

254 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...