Question about 1999 Jeep Grand Cherokee

1 Answer

AC Fan Stopped Working

Ive removed a box which appears to be the ac fan module. The area where the connector is to be place seems to be melting. Does anyone have a wiring schematic or know where I can find one? You can guess I am a girl who knows very little about this. Thanks for any help.


Posted by on

  • myers816 Jun 22, 2009

    Thank you!!! I love my jeep and hope to keep it. Ill be placing a few calls tomorrow. Seems like an easy fix, something I can do. Your help is very much appreciated.




1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

Likely you are talking about the blower relay. you can get that part of the harness at a scrapyard and just cut and solder the wires on one at a time. (probably can get a relay there too really cheap) Usually when the plug overheats it' s because either the relay overheated or the blower is drawing too much amperage (worn out) Often you can clean up the connectors and still use the old plug as long as all connectors make good contact.

Posted on Jun 21, 2009

  • Richard Scordino Jun 22, 2009

    no problem...Hope it works out for you!!!



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How long for the ac fan to start working? Ive noticed that the fan does not work when i turn the ac on, can this cause my car to overheat. I check the temp and coolant liquid both seems fine.

the ac fan starts as soon as the ac is switched on
the fan is provide cooling of the condenser before the radiator to prevent high head pressures in the ac compressor
it is the fan at the front of the car mand does not affect engine temp
there is a radiator fan between the engine and the radiator that will not start until the coolant temperature reaches a set temp at which point the ECM switches that fan on
if that fan is not working when the engine is hot , check for fan, coolant temperature sensor switch , fan relay, fuses or problem ECM

Jan 13, 2016 | AC Cars & Trucks

2 Answers

Blower motor fan module

It is probably built right into your switch control

Nov 09, 2015 | 2003 Chevrolet TrailBlazer

1 Answer

04 nissan maxima radio and lcd screen not working ac still works radio comes on when I start the car then shuts off was told itz not a fuse what could it be and how can I check it

04 nissan maxima radio and lcd screen not working but ac ...
5 hours ago - Run a 12 volt jumper lead to the fan motor connector from the battery or fuse box, if the fan runs replace the fan speed control module.

Sep 21, 2015 | Nissan Cars & Trucks

4 Answers

Why do i need to keep adding coolant

It Sounds Like Your Car Is Overheating Witch Will Cause The Air Not To Work And Your Water Is Probably Going Out The Overflo. you most likely need a new fan.

Jun 14, 2014 | 2004 Hyundai Santa Fe

1 Answer

The ac is not blowing air

there is a resister for the blower motor near the motor under the dash behind the glove box the connectors over heat then they loose electrical contacts look at the connector for melting

Jul 12, 2012 | 2004 Cadillac CTS

1 Answer

AC Fan Motor Goes Off and On

There is a wire connector repair kit available at your local dealer. You may also need to replace the resistor module due to the connector being melted in the cavity. The heat is a result of a loose connection (high resistance) that eventually melts the connector to the module. Hope this helps.

Jul 13, 2009 | 2004 Jeep Grand Cherokee

2 Answers

2003 Suzuki Aerio Blower Fan

Mine did the same thing and I found the connector on the blower wiring harness was all melted and chared from overheating. I took out the blower assembly, cleaned the connector terminals, cut off the melted wiring harness connector and crimped on new female connectors. Seems to work ok now, I just hope it doesn't melt again

Jul 02, 2009 | 2003 Suzuki Aerio

2 Answers

VW Jetta GL 2000, AC - Heater Fan stopped

blower motor or resistor or the blower motor control switch.

Jun 01, 2009 | 1998 Volkswagen Jetta

1 Answer

My AC/Heat fan is not working

my 06 h3 just had same problem, the motor control resistor pack was bad, located under glove box, mounted inside ac duct, large connector and two screws will remove it.
mine had burnt spot on connector,cleaned connector terminals and installed new pack, works fine now. I found your problem while looking for another elec problem i'm having.

Nov 17, 2008 | 2006 Hummer H3

1 Answer

95 Saab 900

If the low speed fan doesn't come on, but the system works when cooling air is blown through it, that says that whatever temperature sensor is used is working. It also seems that, if the fuse is OK, then the switch for the fan isn't working. There should be a switch module down there near the fan (you'd see wires from the fan to a harness, and it'll plug into a module). I'd be willing to try replacing that switch and see if it solves the problem.

Jun 20, 2008 | 1995 Saab 900

Not finding what you are looking for?
1999 Jeep Grand Cherokee Logo

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides