Question about 1985 Lincoln Town Car

1 Answer

How do you reprogram the keyless door lock code?

I bought a Towncar recently and am trying to find how I'd go about changeing the lock /unlock/trunk open code on the door key pad.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 770 Answers

  1. Enter the five digit permanent entry code into keyless entry keypad.
  2. Within five seconds of pressing last button of permanent code, press the 1/2 button within five seconds of pressing the last button of the permanent code. (Factory code found on the module).
  3. Enter any alternate five digit code within five seconds of pressing 1/2 button.
    • Enter a sixth digit as follows to indicate operator's memory seat setting to be set by alternate code: 9/0-- no memory recall
      1/2-- memory seat position 1
      314-- memory seat position 2
      5/6-- memory seat position 3
    • After successful programming, the doors will signal by locking and then unlocking.

The Keyless Entry Module is located inside the drivers side door.

Posted on Jun 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Reprogram door locks


You can call or visit your local or 800 Ford Dealer on this one. It should be a free service to help locate the factory code usually located in the trunk...to test your keyless pad...enter #s...8 then 9...this should lock all doors...After you get the factory code, your owners manual should be step by step to personalize a new code...Hope this helps.

Oct 03, 2013 | Mercury Mariner Cars & Trucks

1 Answer

2001 mustang keyless entry not working properly what do I do


You did it like this ?
Programming -Keyless Entry Remote Transmitter NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: All previous transmitter identification codes (TIC's) will be erased when programming mode is entered.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the generic electronic module (GEM)(14B204), perform the following steps.
  1. Turn the ignition from OFF to RUN eight times within 10 seconds, ending in RUN. If the GEM has successfully entered program mode, it will lock and unlock all the doors.
  1. NOTE: The first TIC must be entered within 7.5 seconds of entering the program mode and additional TICs must be entered within 7.5 seconds of the first TIC. The programming mode is exited whenever the timing constraints are not met. Press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait for several seconds and press the button again.
  1. Turn the ignition switch to the OFF position, or wait up to five minutes after step 1, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the GEM will lock and unlock all the doors one last time.

Jan 15, 2018 | 2001 Ford Mustang

2 Answers

Where do I find the keyless entry code for my 1999 Mercury Mountaineer? Then when I use the remote to unlock or lock the Mountaineer, the locks will pop up or the horn will blow or all four locks will...


TRY THIS REPROGRAMMING PROCEDURE. SWITCH THE IGNITION OFF TO ON 8 TIMES WITHIN 10 SECONDS. DOORS SHOULD LOCK THEN UNLOCK. PRESS ANY BUTTON ON THE FIRST REMOTE TRANSMITTER. DOORS SHOULD LOCK THEN UNLOCK. IF YOU HAVE ANOTHER CAR REMOTE REPROGRAM IT THE SAME WAY. WHEN DONE SWITCH IGNITION SWITCH OFF.

Jan 27, 2011 | 1999 Mercury Mountaineer

2 Answers

I need the code for the door locks


try looking in the trunk on one of the hinges,usually there is a little white sticker with the code on it,and when tyin in the code add a 5 to it to unlock the passenger door or a 9 to pop the trunk,hope this helps

Oct 13, 2010 | 1994 Lincoln Town Car

1 Answer

How do i reprogram electronic door locks


Programming Electronic Door Lock Control System NOTE: The electronic door lock control processor (14B001) erases all previous keyless entry remote transmitter (15K601) from memory when the keyless entry remote transmitters are programmed or reprogrammed. The electronic door lock control processor can store up to four keyless entry remote transmitters in memory.


  • To program (or reprogram) keyless entry remote transmitter into the electronic door lock control processor, perform the following steps:
  1. Turn ignition switch to the RUN position and momentarily short the two terminals of the program connector taped to the wire assembly and located behind the glove compartment. All doors should lock and then unlock. Remove shorting pin.
  1. Press any button on keyless entry remote transmitter. All doors should lock and then unlock to verify the keyless entry remote transmitter has been programmed. If door locks do not respond, press button again (up to three times maximum with the same keyless entry remote transmitter).
  1. Repeat the above step to program additional keyless entry remote transmitters into the electronic door lock control processor (up to four keyless entry remote transmitters maximum).
  1. Turn ignition switch OFF. All doors should lock and then unlock.
  1. Check operation.

Jun 05, 2010 | 1997 Ford Windstar

1 Answer

New batteries but remote won't click the door(s) or trunk. Ron


try programming the remote again, here is how u do that. if this doesn't fix the problem the remote may be defective, if you need a new one try ebay, they are very cheap to buy there.

.

Note: Existing keyless remotes will be erased with this procedure.
Existing working remotes will have to reprogrammed also.
1. Locate the programming connector wire located in the RH trunk area.
You may have to pull back right side trunk trim on trunk wall to locate
the single black/white wire.

2. The programming connector wire should have one termial in the plastic
connector on end of black/white wire. Ground the terminal in the connector
to a nearby bolt or trunk latch.
Leave connector wire connected to ground through out procedure.
3. System will now lock and unlock doors automatically to indicate
programming mode has been activated.
4. Press any button on keyless remote. System will respond by locking
and unlocking doors one time to indicate successful programming.
5. Repeat step 4 for to program any additonal keyless remotes including
and existing keyless remotes. Do not remove ground wire between
programming of keyless remotes.
6. Disconnect programming connector wire from ground to exit programming
mode.
7. Test keyless remote(s).

Nov 30, 2009 | 1994 Pontiac Grand Prix

1 Answer

Chevy malibu keyless entry malfunction


Key fobs have to be reprogrammed. something has knocked the coding off. Search the web for procedures to program fobs. It usually entails operating ignition a series of power lock sequences and the like. If that does not work you can take it to the dealer and they can recode it using the data from you cars computer, but that is extremely expensive.

Jul 30, 2017 | 2005 Chevrolet Malibu

2 Answers

Need the factory keyless entry code to reprogram drivers door keypad. Owners manual insert is no longer available.


Check inside the trunk lid for a label with a 5 digit code. If unsuccessful, then any dealer would be able to help you by checking the VIN number.

May 11, 2009 | 1998 Lincoln Continental

1 Answer

Car will not unlock.


To get inside the car .... Use the key in the lock cylinder, unlock the drivers door to get inside. You shouldn't have to reprogram the fob unless it or the keyless module was changed. There may be a blown fuse that supplies the keyless control module (check the owners manual for location). or wires that lead into the Drivers door may be damaged ... The keyless module is located inside the drivers door at the bottom behind the door panel ... do the unlock/lock and trunk release switches on the inside of the drivers door operate the locks and or trunk release? If so it is not the fuse ... and not the wires to it ... And it could be your BCM body control module, located in the dash board to right of your gas petal. Because the number entry keypad (code for that is on the inside of the right passenger trunk bracket arm) also doesn't work I assume it's not the key fobs themselves. Your 98 manual is correct for your car.

Apr 02, 2009 | 1998 Mercury Grand Marquis

1 Answer

Programing keyless entry


If you have an owners manual the programming instructions are in there. If no manual here they are:

1. Turn the ignition off.
2. Ground the receiver program terminal. Jump the two terminals located in the programing ground connector. (What this means in simple terms is locate the wires that run on the right side of the trunk. There is two black wires that has a plug on the end with two prongs. It is in between the antenna and tail lights.)
3. Within 2 seconds of connecting the prongs the door locks will lock. The unlock and the rear compartment lid release will produce a cycle, causing the horn to chirp. This indicates that the module is ready for reprogramming.
4. Press and hold the lock and unlock buttons at the same time until the doors lock and unlock. The rear compartment lid will release and the horn sounds to indicate that the transmitter has successfully been reprogrammed. (Hold buttons down for approximately 12 seconds)
5. Repeat the previous step for the remaining transmitters.
6. Remove the jumper at the program connector.
7. Verify the proper operation of each transmitter

Sep 30, 2008 | 2007 Chevrolet Malibu SS Sedan New Cars

Not finding what you are looking for?
Cars & Trucks Logo

1,027 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

Marvin
Marvin

Level 3 Expert

81424 Answers

gerry bissi

Level 3 Expert

4376 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...