Question about 1999 Chevrolet Silverado 1500

1 Answer

Door pin changing

How do change door pins on a 2000 chev silverado do you have a picture as to how it isdone thanks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 6,982 Answers

Most I've changed have just been able to be driven up from the bottom. Support the door with a floor jack to take tension off of it and be careful not to let worn grooved spots prevent the pin from moving upwards. Most good kits I've seen also come with bronze replacement bushings...worth the couple of dollars extra.

Posted on Jun 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the door hinge pins?


get a floor jack and a pieces of wood lay the wood on the jack and jack up till it meets the bottom of the door. this will support the door when you pull the pins. using a pry bar pop the little spring inside the door out. its on the top hinge.if the pins have a retainer on the end of them remove this clip the new ones came with this. using a hammer and long punch drive out the pins and pull the door. if it has electric windows just pull it away enough to access the holes for the pins. using the hammer and punch drive out the bushings and install the new bushings.slide the door to the holes and install the new pins make note of the direction of the old pins and install the same way. install the clips on the ends of the pins and reinstall the spring. i do so many i made a tool for reinstalling the spring its a little tricky to get in with your pry bar but not installing the pin will cause the door to swing without restraint. heres a break down picture to help guide you. hope this helpsonetufshoppe_67.gif

Jan 28, 2011 | 2000 Chevrolet Silverado

1 Answer

I have a 99 chev silverado 4x4 w/plow pkg long bed i need to replace the door hinge bushings and or pins the pins there are 4 of them 2 each hinge about 3/4 long or so i have the c clips off and using a...


Take the load of the door and find the sweet spot due to the wear of the pin .......It is sitting in the worn grove of the pin causing it to bind...........Hope this helps you out.

Aug 21, 2010 | Chevrolet Silverado 2500HD Cars & Trucks

1 Answer

HOW DO I CHANGE A CARRIER CASE FOR A 1999 CHEV SILVERADO


remove both wheels
Remove the center axle cover
remove the inner axle C clips
they just slide right out easily
Disconnect the drive shave
Remove the pinion nut behind the drive shaft on the axle
Remove the screw inside the pin for the pinion gears
remove 2 pinion gears and the shaft
Now you can gain access the the bolts for the carrier

Mar 24, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

Need directions how to change turn signals on 99 chev. silverado


If you're after changing the bulbs, then here you go. Raise the hood. Looking at the top of the headlight assembly, you will see either one or two pins that are shaped like an upside-down "L". You'll only see the part that goes across. Pull the pins up, and pull the assembly foreward, out of the body. Disconnect the wires, and set it aside. Look at the turn signal from above. There is a plastic clip that you have to push in on, and then the turn signal housing will swing away from the body. You can then change the bulb. After you're done, but it back like you found it, and you're good to go.

Oct 21, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

How do you change hinge pins in drivers door


The repair kit that you purchase should have recommended steps for replacement. With the kit that I purchased, I had to grind the bottom of the upper & lower pins off. Since this was a quick fix, my brother assisted by holding the door steady on the blocks that we set the door on. I removed the old pins. The new pins were threaded and were pulled into place as the retaining nuts were tightened. We set the door back in place and were done. I purchased the pin kits from my buddy at a local body shop.

Sep 29, 2009 | 1999 Chevrolet Silverado 1500

2 Answers

Do i need a specail tool for door pins for a 2001 chev blazer


There is a special tool that they make, but it is not necessary. It does make the job easier though.


cacb96c.jpg

Sep 07, 2009 | 2001 Chevrolet Blazer

1 Answer

Change door pins where do i begin


get a floor jack and a block of wood, open the door fully and support the door (if you have a helper it makes it a lot easier to have someone hold the door as well, tap the pins out with a punch of some kind and a hammer, i would also change the bushings for the pins, tap the old bushings out then tap the new ones in, be carefull and note which direction the bushings and the pins are facing, its not hard at all just takes some finesse and time, hope this helps!

Jun 17, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

Replacing interior door handle 1995 chev pick up


Just pull on the Bottom of the Panel and you will be Started. There are a Couple of Screws in the Top panel Like the Arm Rest and the Handle Housing. Got a 95' Silverado also. This happens from time to time. Start at the Bottom of the Door Panel and Loosen. Remove the Screws from the Top Panel. The Panel will Probably not come all the Way off so, You will need to work under it. That Handle is just Pinned. Once you get up to it Just remove the Pin. Buy some Replacement Plastic Clips for the Panel. You will need them!

Jan 22, 2009 | 1995 Chevrolet Silverado 2500

1 Answer

Replace inside door handle 95 chev pick up


Got a 95' Silverado also. This happens from time to time. Start at the Bottom of the Door Panel and Loosen. Remove the Screws from the Top Panel. The Panel will Probably not come all the Way off so, You will need to work under it. That Handle is just Pinned. Once you get up to it Just remove the Pin. Buy some Replacement Plastic Clips for the Panel. You will need them!

Jan 22, 2009 | 1995 Chevrolet Silverado 2500

1 Answer

Head light assy


new body style or old?
old body you will see a pin on top of lamp assembly slide pin out and light will come out.
new body remove two 10mm bolts and lamp will come out

Oct 21, 2008 | 2007 Chevrolet Silverado 1500 2WD

Not finding what you are looking for?
1999 Chevrolet Silverado 1500 Logo

Related Topics:

266 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...