Question about Ford F-250

2 Answers

My lifted 4x4 struck the base of a tree with only the right front tire,driving it up and back.the right wheel apears to be slightly turned out,and the frame crossmember is bent and or cracked.the right 36 in. tire did contact the fender pushing it into the door so it wont open.can the crossmember be replaced and fraim straightened?

Posted by on

  • jasonerbach Jun 21, 2009

    Its a 95 f250 4x4 with a 469 and auto, and the fraimrails are not noticably bent. thank you .heavymetal 77and co7196.

    jasonerbach

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Ford Master
  • 3,433 Answers

Oh yeah, They can work miracles nowadays. If the rail is too badly bent it will be expensive.. Good luck

Posted on Jun 21, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 721 Answers

The cross member must be replaced. The frame is probably not bent, unless you were going 50 mph or so. It could be straightened in any event. Not knowing the make & model also makes this a tough question to accurately answer.

Posted on Jun 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 2000 ford expedition 4x4 the front right side makes a clicking noise while driving. Any ideas


Clicking Noise From Left Front Tire Area - F150online Forums

www.f150online.com/.../47713-clicking-noise-left-front-tire-area.html
Aug 11, 2001 - I have a clicking type noise comming from the left front tire. It does not ... I can really hear it when I'm driving beside a sound wall or the side of a building. ... the sound. (Yeah right!) ... Almost forgot: 1999 Ford F150 XLT Supercab 5.4 4X4. ... My 2000 4X4 had a ting ting noise coming from the left front wheel. Intermitent Grinding Noise on 2004 F150 4x4 - Page 5
Jan 15, 2010
Popping noise in front end.
Oct 26, 2009
Clicking noise at low speeds.
Aug 7, 2009
Annoying clicking sound in rear of truck?!?!
Jun 8, 2009
More results from www.f150online.com

Jan 05, 2016 | Ford Cars & Trucks

1 Answer

How do you get the tire off a 2005 Dakota once the lug nuts have all been taken off.


Hi Richard:
These can be a PITA!
The diameter of the centre of the wheel can be a nasty tight fit.
Here's a couple of techniques:
- Old brute force trick......... use spare tire as "pendulum" hammer and smack the stuck tire... front.back.front.back
- If front tire, turn all the way to side being removed.... but block of wood between rim and frame.... turn back against rim.
- Put lug nuts back on leave slack. Lower vehicle back to ground and drive slowly forward and back. If front tire, turn back and forth.
Sometimes this will loosen them
- If rear tire, slide 4X4 across from under vehicle. block so it is against rim, then smack 4X4 with LARGE sledge hammer.
- Some people apply heat to the centre of the wheel where it is jammed. I don't like doing that.
BRUTE FORCE is much more satisfying.
Cheers.

Nov 08, 2015 | Cars & Trucks

1 Answer

Can i manualy take it out of 4x4


Those older fords you have to put the 4x4 selector into 2H or 2 High on the floor shifter. Then go to the front tires and in the very center of the tire there will be a knob that say Locked and Unlocked. Turn the knob to unlocked on both sides. Then you will not have front wheel dragging on the drive train and only the rear wheels will be the drive tire. TO put it back in 4x4. Turn the knob back to locked on each front tire and put the truck in 4H or 4 High to get 4x4. Only use 4L or 4Low when your stuck to prevent spinning your tires with full power.


Now if your has the automatic locking hubs I would switch them out with manual ones because the automatic ones were problematic where they get stuck or not work at all. It requires replacing the locking hub assembly which isn't that hard to do.

Feb 06, 2015 | 1990 Ford F150

1 Answer

Clicking noise during turning,


I'm going to assume that the Yukon is a 4X4, and will therefore also assume that the clicking noise is coming from one of the two drive axles (likely the right side). Check under the truck near the wheels and you will see the drive axles with a rubber bellows boot on either end. It is likely that the boot closest to the wheel has torn and allowed the grease to escape the constant velocity (CV) joint. The boot or possibly the axle will have to be replaced.

Feb 13, 2014 | 2001 GMC Yukon XL

1 Answer

4wd silverado 2500 hd


Check the oil in the transfer case. If it has lots of metal in it... time for a new one. They aren't the world's strongest.
Another check: Lift the front of the truck, while keeping the rear wheels on the ground. Engage the 4x4 switch (then turn the truck off) crawl under and try to turn the front driveshaft by hand. If it turns and the wheels turn, the transfer case is the problem if it turns but the front wheels don't... front diff issues. Any grinding, crunching etc is also a clue.

Dec 30, 2013 | Chevrolet Cars & Trucks

1 Answer

I just bought an2003 ford explorer 4x4 and i have a loud humming noise coming from the front end tires are brand new it has around 190,000km please help


If the noise is only when the vehicle is moving it sounds lek you have a bad wheel bearing. You can inspect ford move ment or play shaking the tires up and down and left to right while lifted up on hoist or jack. If there is no movement doesn't necesarily mean the bearings are okay, however if there is movement in bearing replace and drive again. Antoher way to determine Which wheel bearing is bad is to drive and turn to the left, if the noise gets louder than it mens the rightside wheel bearung is bad. If you turn to the right and noise gets louder replace driver side front wheel bearing. Also Rub your hands across your tires, does it feel wavy or uneven, you could have cupped tires, I DON'T KNOW HOW NEW THEY are but cupped tires will also make this noise. One way to see if it is the tires is to do a rotate If noise changes at all then you no its a tire causing noise. Hope this helps.

Oct 19, 2010 | 2003 Ford Explorer

1 Answer

I have a 2003 f150 4x4 and the front tires are not engaging. Have replaced the ac-curator and the shift fork assembly in the front differential. And fixed 6 vacuum leaks. The 4x4 is a manual shift with...


Lift and support the front of the truck so the front wheels are off the ground ( take safety precautions, chock wheels, jack stands, etc )
Key on, engage 4x4 and try to turn the front drive shaft.
If it turns it is a problem with the transfer case.
If it doesn't it is a front axle engagement problem.

I don't want to assume that the front axle works correctly, but it sounds like you got past that bit of testing.

Aug 18, 2010 | 2003 Ford F150 Regular Cab

2 Answers

Truck makes humming sound, volume increases with speed and turn


Wheel bearings is my guess. Confirm this by jacking the vehicle up with wheels on and check for play. Grab the tire by the top and bottom and wiggle it in and out, the will be excessive play. Given the fact that you gave a clear explination i am almost certain its bearings. You will need to purchace new bearings(Inner and Outer), Hub Seals, and possibly a possibly an axle seal kit for the 4x4 drive axle (they get old and stick to the axle durring disassembly) and keep in mind that to get the outter races of both bearings in the hub need to be "Pressed" out a a machine shop, or by any shop that might have a press.

Oct 07, 2009 | 2003 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...