Question about Kia Sportage

1 Answer

Trying to adjust power steering belt on my 1998 kia sportage,i found the lower pivot can you describe where the tensioner is

Posted by on

  • eric_proudfo Jun 21, 2009

    can you supply a diagram

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,197 Answers

The tensioner acts as an idler pulley and is located on either the inside or outside of the accessory drive belt. Its provides the correct tension for initial belt adjustment and maintains this critical tension adjustment during vehicle operation. It can be found on conventional V-belts and the newer serpentine ribbed belts.
there is an adjustment tab or hook under neath and you just about have to lay flat on your back pull up the tension and have someone else tighten the bolts from above.
with everything aligned loosen the tensioner nut and pry it to the left with a small crowbar or long screw driver or something elongated. When the tensioner pully is pushed as far as it will go to the left, tighten the nut. This will make it much easier to get the belt off and on.
if u feel i ve been of help... kindly rate my service....
good luck

Posted on Jun 21, 2009

  • SAM JAYANTH CHANDRASEKAR

    yes sure.....


    kindly check out the below links for the diagrams.....


    you ll be downloading a pdf file..... it has all the diagrams u need....


    http://www.avigex.ca/kia/Belt4.PDF




    kindly rate my service .......... good luck

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Need timing belt digram for a 2000 kia sportage


eb770f2.gif
  1. Install lower timing belt cover.
  2. Install upper timing belt cover.
  3. Install power steering drive belt and adjust belt tension.
  4. Install fan pulley.
  5. Install generator drive belt and adjust belt tension.
  6. Install A/C drive belt and adjust belt tension.
  7. Install splash guard.
  8. Install fan and fan shroud.
  9. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
  10. Install fan shroud mounting bolts.
  11. Install fresh air duct.
  12. Connect hose to resonance chamber.
  13. Connect battery negative cable.

Apr 17, 2013 | 2000 Daewoo Nubira

1 Answer

How to replace the power steering belt on a 4g13



ADJUSTMENT

Excessive belt tension will cause damage to the alternator and water pump pulley bearings, while, on the other hand, loose belt tension will produce slip and premature wear on the belt. Therefore, be sure to adjust the belt tension to the proper level.
To adjust the tension on a drive belt, loosen the adjusting bolt or fixing bolt locknut on the alternator, alternator bracket or tension pulley. Then move the alternator or turn the adjusting bolt to adjust belt tension. Once the desired value is reached, secure the bolt or locknut and recheck tension.


REMOVAL & INSTALLATION

1.5L, 1.6L, 1.8L, 2.0L and 2.4L Engines


0900c15280037bf7.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory V-belt routing-Mitsubishi 1.5L, 1.6L, 1.8L, 2.0L and 2.4L engines
Alternator Belt


0900c15280037bf8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Loosen the adjuster lock bolt . . .


0900c15280037bf9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. . . . then remove the alternator belt from the engine

  1. Loosen the alternator support nut.
  2. Loosen the adjuster lock bolt.
  3. Rotate the adjuster bolt counter clockwise to release the tension on the belt.
  4. Remove the belt.

To install:
  1. Install the belt on the pulleys.
  2. Rotate the adjuster bolt clockwise until the proper tension is reached.
  3. Tighten the adjuster lock bolt and the alternator support nut.

POWER STEERING BELT


0900c15280037bfa.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. After the adjusting and fixed bolts are loosened, rotate the pump . . .


0900c15280037bfb.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. . . . then remove the power steering belt from the engine

  1. Remove the alternator belt as described above.
  2. Loosen the power steering pump adjusting bolts.
  3. Remove the power steering pump fixed bolt on the rear of the bracket.
  4. Rotate the pump toward the engine and remove the belt.

To install:
  1. Install the belt on the pulleys.
  2. Rotate the pump until the proper tension is reached.
  3. Tighten the adjusting bolts on the pump.
  4. Tighten the fixed bolt on the rear of the bracket.
  5. Install the alternator belt.

A/C COMPRESSOR BELT
  1. Loosen the tension pulley and remove the belt.
  2. The installation is the reverse of the removal.

3.0L DOHC, 3.0L SOHC Galant, and 3.5L Engines


0900c15280037bfc.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Serpentine belt routing-Mitsubishi 3.0L engines (except 1998-00 Galant models)


0900c15280037bfd.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory V-belt routing-Mitsubishi 3.5L and 1998-00 3.0L SOHC Galant engines
ALTERNATOR AND A/C COMPRESSOR

  1. Disconnect the negative battery cable.


CAUTION Wait at least 90 seconds after the negative battery cable is disconnected to prevent possible deployment of the air bag.
  1. Raise and safely support the vehicle and remove the front undercover.
  2. Loosen the tension pulley fixing nut and relieve the tension on the belt by turning the adjusting bolt.
  3. Remove the belt.

To install:
  1. Install the belt on the crankshaft and alternator pulleys.
  2. Using the adjusting bolt on the tensioner, tighten the belt to the desired tension.
  3. Tighten the fixing nut to hold the adjustment.
  4. Install the undercover and lower the vehicle to the floor.
  5. Connect the negative battery cable.

POWER STEERING BELT
  1. Disconnect the negative battery cable.


CAUTION Wait at least 90 seconds after the negative battery cable is disconnected to prevent possible deployment of the air bag.
  1. Raise and safely support the vehicle and remove the undercover.
  2. Remove the alternator and A/C compressor belt.
  3. Lower the vehicle and remove the cruise control pump link assembly.
  4. Place the power steering hose under the oil reservoir.
  5. Loosen the tension pulley fixing bolts and remove the power steering pump drive belt.

To install:
  1. Install the power steering pump drive belt.
  2. Insert an extension bar or equivalent into the opening at the end of the tension pulley bracket and pivot the pulley to apply tension to the belt.
  3. Tighten the fixing bolts.
  4. Raise the vehicle and install the alternator and A/C compressor belt.
  5. Install the undercover and lower the vehicle.
  6. Connect the negative battery cable.

3.0L SOHC Diamante
  1. Disconnect the negative battery cable.
  2. Loosen the lockbolt on the face of the A/C tensioner pulley.
  3. Turn the adjusting bolt of the A/C tensioner pulley to loosen the tension of the A/C belt.
  4. Remove the A/C compressor belt.
  5. Loosen the locknut on the face of the power steering/alternator tensioner pulley.
  6. Turn the adjusting bolt of the tensioner pulley to loosen the tension of the belt.
  7. Remove the power steering/alternator belt.

To install:
  1. Install the power steering/alternator belt first and then the A/C compressor drive belt.
  2. Adjust the belts to the proper tension by turning the adjusting bolts and tighten pulley fixing nut/bolt.
  3. Tighten the mounting nut of the power steering/alternator tensioner pulley to 36 ft. lbs. (50 Nm).

Mar 21, 2013 | 1996 Mitsubishi Mirage

1 Answer

Need belt routing diagram for 2001 chrysler sebring lxi


Thanks for using FixYa.




jturcotte_2444.gif

Fig. Accessory drive belt routing-2.7L engine
Chrysler Cirrus & Sebring Convertible; Dodge Stratus; Plymouth Breeze



jturcotte_2445.gif

Fig. Accessory drive belt routing-Chrysler 2.7L engine





2.7L Engine
A/C & Alternator Belt

  1. Raise and safely support the vehicle.
  2. Remove the right front wheel and belt splash shield.
  3. Loosen tensioner locking bolt and pivot bolt.
  4. Rotate tensioner clockwise to allow enough slack to remove belt

To install:
  1. Install the air conditioning compressor/alternator belt on pulleys, tensioner in slack position, slip belt over idler last.
  2. Adjust drive belt tension.
  3. Install the belt splash shield and right front wheel.
  4. Lower vehicle.
    jturcotte_2446.gif

    Fig. Installing A/C & alternator belt-2.7L engine


  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Raise and safely support the vehicle.
  3. Remove the right front wheel and belt splash shield.
  4. Loosen the tensioner locking bolt and pivot bolt.
  5. Rotate tensioner clockwise to allow enough slack to remove the belt

To install:
  1. With the tensioner in a slack position, install the Air Conditioning (A/C) compressor/alternator belt on the pulleys. Slip the belt over the idler last.
  2. Adjust the drive belt tension.
  3. Install the belt splash shield and right front wheel. Tighten the wheel lug nuts to 100 ft. lbs. (136 Nm).
  4. Lower the vehicle.

Power Steering Belt
  1. Raise and safely support the vehicle.
  2. Remove the right front wheel and belt splash shield.
  3. Remove the air conditioning compressor/alternator belt.
  4. Loosen belt adjusting bolt. It is not necessary to loosen the pivot bolt on the power steering pump. There is a bushing incorporated into the power steering pump/bracket that allows it to pivot.
  5. Remove the power steering belt.

To install:
  1. Install the power steering belt on pulleys.
  2. Adjust drive belt tension.
  3. Install the air conditioning compressor/alternator belt.
  4. Install the belt splash shield and right front wheel.
  5. Lower vehicle.


Oct 27, 2011 | Cars & Trucks

1 Answer

Is there a tensioner for the fan belt and where can I locate it? Squicky belt and battery keeps getting drained. thanks


If this belt is only driving the alternator, water pump, and similar, the adjustment for belt tension is normally at the alternator, not a separate tensioner. If it is set up this way, the alternator will have a pivot bolt and a second one that is in a curved, elongated slot. This latter one sets tension. Gently loosen the pivot bolt (let it still drag) and then the adjustment bolt. While you are getting hands dirty, check the inside curve of the belt for cracks; tightening a sick belt isn't a good idea.
Look for the longest straight stretch and adjust the tension so the belt will deviate 1/4 - 1/2" under moderate pressure.
If your setup is different (or even if not), I recommend that everyone should have a service manual for their vehicles if reasonably priced such as Haynes (first choice) or Chilton (#2).
Haynes is no longer offering them but existing stock is around:
Kia Sportage '95-02'

Jun 01, 2011 | 2000 Kia Sportage

1 Answer

I want to know how to remove the alternator kia optima 2003


  1. Disconnect the negative battery cable.
  2. Temporarily loosen the water pump pulley bolts, 1.6L (VIN 3) engine only.
  3. Remove the front air intake inlet pipe bolts, 1.8L engine only.
  4. Remove the top hose from the air intake inlet pipe, 1.8L engine only.
  5. Remove the air intake inlet pipe clamp and the pipe, 1.8L engine only.
  6. Remove the power steering pump, 2.0L engine only.
  7. Remove the power steering pump bracket, 2.0L engine only.
  8. Remove the alternator B terminal cover cap.
  9. Disconnect the alternator electrical connections.
  10. Loosen, but do not remove the alternator pivot bolt and the tensioner mounting bolt.
  11. Remove the drive belt(s); relieve tension on the belt by rotating the adjustment bolt.
  12. Remove the water pump pulley, 1.6L (VIN 3) engine only.
  13. Remove the power steering pump, 1.6L (VIN 3) engine only.
  14. Remove the power steering pump bracket, 1.6L (VIN 3) engine only.
  15. Remove the alternator tensioner mounting bolt and the belt tensioner.
  16. Remove the alternator pivot bolt.
  17. Loosen the bolt at the base of the adjusting bracket and rotate the bracket up.
  18. Remove the alternator.

    0996b43f80207fa4.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Alternator mounting-1.5L and 1.6L (VIN 5) engine shown


    0996b43f80207fa5.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Alternator mounting-2.0L and 1.6L (VIN 3) engines shown


    0996b43f80231908.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Alternator mounting-2.4L and 2.7L engine


To install:
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Install the alternator.
  3. Install the alternator pivot bolt and hand-tighten at this time.
  4. Rotate the adjusting bracket into position, place the belt tensioner into position. Hand-tighten the mounting bolt.
  5. Install the drive belt.
  6. Adjust the belt tension by rotating the adjustment bolt.
  7. The belt deflection for 1.5L, 1.6L (VIN 5), 2.4L and 2.7L engines, is as follows:
    1. New belt: 0.22-0.28 in. (5.5-7mm).
    2. Used belt: 0.24-0.28 in. (6-7mm).

  8. The belt deflection for 1.6L (VIN 3) engine is as follows :
    1. New belt: 0.13-0.15 in. (3.3-3.7mm).
    2. Used belt: 0.17-0.19 in. (4.2-4.7mm).

  9. The belt deflection for the 2.0L engine, is as follows:
    1. New belt: 0.22-0.31 in. (5.5-8mm).
    2. Used belt: 0.33-0.45 in. (8.5-11.5mm).

  10. The belt deflection for the 1.8L engine, is as follows:
    1. New belt: 0.23-0.31 in. (6-8mm).
    2. Used belt: 0.28-0.35 in. (7-9mm).

  11. Tighten the tensioner bolt to 14-19 ft. lbs. (19-26 Nm) and the pivot bolt to 28-38 ft. lbs. (38-51 Nm).
  12. Connect the alternator electrical connections.
  13. Install the alternator B terminal cover cap.
  14. Install the power steering pump and adjust the power steering belt tension, 2.0L and 1.6L (VIN 3) engines only.
  15. Install the water pump pulley, 2006 1.6L engine only.
  16. Install the air intake inlet pipe and fasten the clamp, 1.8L engine only.
  17. Install the top hose to the air intake inlet pipe, 1.8L engine only.
  18. Install the front air intake inlet pipe bolts, 1.8L engine only.
  19. Connect the negative battery cable.

Feb 09, 2011 | 2003 Kia Optima

2 Answers

The power steering belt is broke on a kia sportage 2001 is it very expensive to fix..


I would replace it yourself....very simple to do! The belt is $13.00 Power Steering Pump Belt
  1. Disconnect the negative battery cable.
  2. Remove the A/C and alternator drive belts for access.
  3. Loosen mounting lock bolt (A) and mounting bolt (B).
  4. With tension released removed the belt.
To install:
  1. Properly route drive belt around the pulleys.
  2. Carefully pry on the power steering pump using a suitable lever. Adjust belt tension is 22 ft. lbs. (30 Nm) when measured at deflection point shown.
  3. Retighten bolts (A) and (B) to 31 ft. lbs. (42 Nm).
  4. Reinstall the A/C and alternator drive belts.
  5. Connect the negative battery cable.
a30e7b7.jpg

Oct 10, 2009 | 2000 Kia Sportage

1 Answer

2001 kia sportage need to get info on how to change the timing belt, 2.0 motor forward facing motor, needs power steering replaced, timing belt.


Hi there,

Below are the steps..

Disconnect the negative battery cable. Remove the two fresh air duct mounting bolts on the radiator. Loosen the fresh air duct clamp at the intake housing. Remove the hose at the resonance chamber. Remove the frech air duct. 2bea4d1.jpg Remove the five cooling fan shroud bolts. ab00c68.jpg Remove the four thermo-modulated fan nuts. Remove the four thermo-modulated fan cooling fan shroud at the same time. 289c5ca.jpg Loosen the two generator mounting bolts(A and B). 2a96c03.jpg Loosen the generator drive belt from the generator by loosening the adjusting bolt(C). Remove the generator drive belt. Remove the fan pulley. Remove the four splash guard mounting bolts and splash guard. f912ce0.jpg Loosen the A/C idler puller nut(A). c0690b5.jpg Remove the A/C drive belt by loosening the adjusting bolt. Loosen the power steering pump lock bolt and mounting bolt. 843d3b3.jpg Remove the power steering belt. Remove five bolts and the upper timing belt cover. Refer to Timing Belt. Remove two bolts and the lower timing cover. Refer to Timing Belt. Loosen the tensioner lock bolt and pivot the tensionder pulley outward to remove the tension from the timing belt, then re-tighten the tensioner lock bolt. 7ca4ca0.jpg NOTE: Tightening Torque : 27-38ft·lbs(37-52N·m) Mark the timing belt rotation for proper reinstallation if it reused. Remove the timing belt. Be careful not to allow oil grease on the belt. c5d4c02.jpg Regards, Jeep Brainy

Sep 16, 2009 | 2001 Kia Sportage

3 Answers

1999 kia sportage timing marks


dfd3ea1.gif Crankshaft match marks


Align marks on timing belt pulley and pump body.

Camshaft pulley alignment marks
9f1c7ef.gif
  1. Align marks on camshaft pulleys with alignment marks on seal plate.
  2. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
  3. Loosen tensioner lock bolt.
  4. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
  5. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
  6. Apply a force of 22 lbs to timing belt between camshaft sprockets.
  7. Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)
  8. NOTE: Replace tensioner spring if timing belt deflection is excessive.
Timing Belt Installation


eb770f2.gif
  1. Install lower timing belt cover.
  2. Install upper timing belt cover.
  3. Install power steering drive belt and adjust belt tension.
  4. Install fan pulley.
  5. Install generator drive belt and adjust belt tension.
  6. Install A/C drive belt and adjust belt tension.
  7. Install splash guard.
  8. Install fan and fan shroud.
  9. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
  10. Install fan shroud mounting bolts.
  11. Install fresh air duct.
  12. Connect hose to resonance chamber.
  13. Connect battery negative cable.

Jul 26, 2009 | 1999 Kia Sportage

1 Answer

Belt came off 1998 chrysler sebring lxi


you have two belts . put the large belt on first . it goes around crank pulley air conditioning pulley alternator pulley.loosen tension pulley to adjust belt. tension. then you put the other belt on power steering pump pulley and crank pulley. adjust belt tension loosen power steering pivot bolt. that it.

Mar 16, 2009 | 1998 Chrysler Sebring

2 Answers

1998 dodge neon airconditioning belt adjustment?


This procedure involves correcting the tension on the power steering accessory and A/C compressor drive belt.

1. Loosen the power steering pump locking bolts A and B and pivot bolt C(Illustration 1 and 2 ) to allow adjustment of belt tension.
2. Using a 1/2" breaker bar, adjust belt tension by applying torque to the square hole "D" on the power steering pivot bracket. Adjust the tension as follows:

Belt tension with no belt replacement: A. Using the Belt Tension Gauge Special Tool Kit C-4162, adjust the belt tension to 100 lb.
B. Tighten in order, first tighten the locking bolt A to 27 Nm (20 ft. Ibs) then, bolt B to27Nm (20 ft. Ibs). Finally tighten the pivot bolt C to 54 Nm (40 ft. Ibs).
Belt tension with belt replacement:
A. Using the Belt Tension Gauge Special Tool Kit C-4162, adjust the belt tension to 135 lb.
B. Tighten in order, first tighten the locking bolt A to 27 Nm (20 ft. Ibs) then, bolt B to 27Nm (20 ft. Ibs). Finally tighten the pivot bolt C to 54 Nm (40 ft. Ibs).
C. Start the engine and allow the vehicle to idle for 15 minutes to allow the belt to seat.
D. Repeat the belt tensioning procedure, set belt tension to 135 lb.

click here for picture 1
click here for picture 2

Jun 13, 2008 | 1998 Dodge Neon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...