Question about 1989 Ford Tempo

1 Answer

How to remove front passenger side wheel berring once it was seized and now we cant get the axel out from behind

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 236 Answers

Best bet is to take it to a mechanic. they had to use a pnuematic hammer to get mine off

Posted on Jun 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change front drivers wheel bearing on mitsibishi colt equipe 2005


Take off the brake assemble meaning remove the roater caliper clean any dirt off the control arm and axel mount take down the upper and lower ball joints then pry them down to allow the axel carrier to pivot down then there should be three bolts behind the bearing remove those and rent a barring puller from autozone then apply the puller to the barings and they should come out this May require a press installer or as in removing the barring you might have to use some wd-40 to spray on the back side of the barring and some hits with a sludge hammer to break it loose if the puller isn't allowed to force the barring out simply and to re assemble it is just the opposite also grease the axel shaft and make sure the surface is clean before installation and use anti seize on all screws and ect this shall help you out

Mar 23, 2014 | Cars & Trucks

1 Answer

Cant get bolts out of cv axel support braket in a mazda 626


This is a bracket mount that has the axle shaft going thru it on the passenger side . the axle must be removed from mount before it can be removed . there is a single bolt that presses against the axle shaft bearing and a snap ring that holds the bearing in the mount once removed the axle will slide out .

Mar 21, 2014 | 1997 Mazda 626

1 Answer

Size of nut on 2002 front wheel axel


need to now the vehicle 1st 2002 what?

Jun 09, 2012 | Cars & Trucks

2 Answers

Need to know how to remove front halfshaft on a 1998 chevy blazer


Google the exact steps...you'll be amazed what you find.

Apr 19, 2011 | Chevrolet Blazer Cars & Trucks

2 Answers

Poping,slipping noise,when you excerate fast.Sound come s from front driver side axle.


Most likely the cv joints, Its cheeper to change the axel out........If not that could be the wheel hub berrings,,,,,,,,,,,,,,,,,good luck

Feb 15, 2011 | 1998 Ford Taurus

1 Answer

Driver side back wheel locked up,even when in nuetral,passenger wheel moves freely in nuetral.


Are you somewhere where it is really cold? you could have a frozen e-brake cable on one side. If that is not possible, You may have a wheel cylinder that is seized so that the brakes wont retract, or a bad axel bearing

Jan 22, 2011 | 1992 GMC Sierra

1 Answer

I dont know how to remove the passenger side front axel in my 1986 ford f150


pull off the rotor-caliper-and behind the rotor is the hub,unbolt it and use a chisel to separate it from the housing,pull that off and wiggle the axel shaft lightly while pulling out and it barely fits through but it will come out.there is a rubber boot on the inner part of the axel,so cut off the clamp so it will come apart..dont hit the threads on the hub,ive done that once and had to use a triangler file to fix the threads

Dec 25, 2009 | 1986 Ford F150 SuperCab

1 Answer

How to remove them from the halfshaft


first of all take the tire off there is four bolts to undo and you should be able to pull out the axel and once its pulled out the berring will have to be pressed off and a new one pressed on at any auto place.

Sep 27, 2009 | 2006 Toyota Land Cruiser

1 Answer

I can't find the oil filter


The filter is way up on right (passenger side) and the back side of the engine. I found it easier to access by removing the rt front wheel and splash barrier plastic panel directly behind where the axel comes through.

Good luck, rhais, 1996 Saturn SL1 4 cycl. sohc

Jun 28, 2009 | 1999 Saturn SL

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...