Question about 1995 Geo Tracker

1 Answer

Need to know the exact location of the reset engine light

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 77 Answers

It depends if you have obd1 or obd2 computer, if you have obd1 jsut remove to battery cable for 5 minutes and it will reset the battery, if its obd2, you will need a code reader/programmer to do it. i am thinking being a 95 it may be a obd1, remove the cable for 5 minutes, go longer if you have the time, and reconect. let me know how it works. good luck.

Posted on Jun 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

SES light on need to read code and reset


You need a code reader can get one for about $30 when you read code know what exactly is wrong and be able to fix and reset

Apr 11, 2016 | 2010 Nissan Versa

2 Answers

How to reset check engine light


Soft reset is disconnecting the battery cables few minutes; if the check engine light turn on again, some fault code is stored there, and will need scanned the PCM (computer) to know exactly what fault is stored there.

Hope helps.

Oct 09, 2011 | 2000 Kia Sportage

1 Answer

How do you reset the check engine light


CHECK ENGINE is one warning about any fault code stored in the PCM; disconnected the battery few minutes to reset it, if the light turn on again, then scanned the PCM to know exactly what code in there.

Keep in touch.

Sep 14, 2010 | 2004 Cadillac Escalade

1 Answer

Service engine soon lights up car will not start. how can i reset to avoid tow charge


Unplugged the baterry for few minutes for reset the ECU; if the light back on, you need scaning your vehicle for details and know exactly what is this fault code.

Hope help.

Feb 10, 2010 | 1999 Oldsmobile Intrigue

2 Answers

Rolled 150000 miles check engine light came on.  is this serious issue or just need computer reset due to miles 


Not likely to be serious; however, have the fault analyzed at AutoZone free. Let us know what they report (code number(s))... They are not allowed to reset the check engine light. Once the issue is handled / repaired, the check engine light can go away by itself (the system re-learns), or if repaired, the light can / will be reset.

Oct 13, 2009 | 1999 Ford Taurus

1 Answer

Where do I find the sensors to replace them? I need a diagram.


It is located on the exhaust pipe. One on each bank normally front and rear. If you go to autozone, they will do a free diagnostic and let you know exactly which one is bad. They are easy to get to and replace, you just need to know which one is bad.

Jun 23, 2009 | 1998 Toyota 4Runner

1 Answer

Where is the obd receptacle located?


you can also read the OBD system by using the check engine light itself, simple rotating the key on and off will cause the light to flash. the exact number of times to rotate will be found in a repair manual. P.s. the OBD connector is under the steering wheel

Jun 07, 2009 | 1996 Dodge Caravan

1 Answer

Where exactly is the fuse for the fuel pump on a 1989 chevy blazer?


I can't say exactly where the fuse is but they are usually located on the firewall in the engine compartment with the fuel pump relay. However many vehicles are also equipped with a reset switch in the event of an accident located somewhere on the vehicle, usually in the trunk. Consult your owners manual or often tow truck drivers know where the reset switches are also.

Apr 30, 2009 | Chevrolet Blazer Cars & Trucks

1 Answer

Oxy sensor light on, and also heat is not working. I dont know


Oxygen sensors are located on the exhaust pipe in front and behind the catalytic convertor. There are more than one. If your check engine light is on, the code will tell you which sensor is faulty - I need that code to tell you the exact location.
Also really need to know the engine type to be more specific.
If your heat is not working there is probably a fault in the door mechanism that lets air pass over the heat exchanger under the dash. the switch is most likely at fault.

Jan 07, 2009 | 2002 Ford Windstar Cargo

4 Answers

Maintenance info


Volvo V50 Maintenance Light Reset

1. Press and hold trip odometer reset button 
2. Turn ignition key to run position KPII (not the start position) 
3. Wait 30 seconds or until service light begins blinking 
4. Release Trip Odometer button 
5. Turn ignition to off position 

Oct 22, 2008 | 2006 Volvo V50

Not finding what you are looking for?
1995 Geo Tracker Logo

Related Topics:

381 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...