Question about Dodge Pickup

1 Answer

Which fuse is for the turning signals on a 981 dodge ram pu

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 721 Answers

I would buy a Hayne's manual or go to www.autozone.com for a diagram. It's free.

Posted on Jun 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of flasher unit 2001 dodge pu 2500 ram


A defective turn signal relay in the Ram 2500 can cause your signals to malfunction or stop working entirely. As a relay ages, so does its circuitry. However, the most common cause of relay damage is attributable to an electrical fault in a relative location, such as the taillight assembly. You can find and replace the turn signal relay in your Dodge Ram 2500 with a few common tools. You can do this job at home; it should take you less than 20 minutes to do.

Things You'll Need :

Phillips screwdriver

Socket wrench set


Instructions:

1. Open the driver's door on your Ram 2500. Reach beneath the front of the driver's seat and pull the seat release lever up. Push the seat toward the rear of the truck as far as it will go.

2. Kneel within the door opening so that you're able to see the bottom of the steering wheel. Below the base of the steering wheel you should see a large square piece of trim panel. This is your Ram 2500's knee-blocker panel.

3. Remove the screw on the top, left and right of the panel with a Phillips screwdriver. Along the bottom lip of the panel--horizontally--you should see three more screws. Remove the screws with your Phillips screwdriver.

4. Take the panel off to reveal your interior relay and fuse cluster. If your turn signal relay has never been replaced, it should be the only white relay in the cluster. If it was replaced before with an aftermarket relay, it will likely be black in color. The square turn signal relay sits on the top, outer right corner of the relay and fuse cluster. It pulls out of place and simply plugs back into position.

I hope this helps.

Apr 30, 2015 | Dodge Cars & Trucks

2 Answers

Have a 1988 dodge pu. Ram no fire to plugs. Replaced coil still the same.


Check to see if getting power to coil. I had a similar problem and the crankshaft sensor wasn't sending signal, no signal no fire. Also check can sensor

Apr 08, 2015 | Dodge Cars & Trucks

1 Answer

2008 dodge pu no rear turn signals or brake lights


you need to inspect wire harness @ rear and along frame rail , corrosion , damaged wire, bad connection, check for continuity, power, ground wires are extremely important . brake light switch could be at fault !!!!!!!!, power to both brakes & turnsignals must be determined , both of these circuits cross each other, see wire diagram

Feb 02, 2013 | 2008 Dodge Ram Pickup 1500

2 Answers

Dodge ram 3500 turn signal - headlight problem


WAY TO GO !!! another "great idea" from vehicle manufactures

Jun 07, 2012 | 2004 Dodge Ram 3500 Truck

1 Answer

Where do you find the turn signal flasher for a 99 dodge ram


on the fuse panel front or look a little higher under the dash. possably on the kick wall

Dec 17, 2009 | 1999 Dodge Ram

1 Answer

Brake/turn signal lights out,already replaced bulbs 96 Dodge Ram


You may have to replace the flasher or a fuse

Aug 11, 2009 | 1996 Dodge Ram

1 Answer

2003 Dodge Ram 2500 diesel 4x4 wiring diagram


TPIM PROBLEM , MUST HAVE COMPUTER FLASHED AT DEALERSHIP

Apr 21, 2009 | 2001 Dodge Ram 2500 Truck

1 Answer

LEFT TRAILER TURN SIGNAL DOES NOT WORK


I have seen once before that the fuse box was bad on a 2003 Dodge 3500. I had power in and nothing out. We had to replace the box. Not cheap! Hope it is simple like a loose connection though. I think I had to pull the inner fender on the drivers side to access the bottom of the fuse box. Pain in the ****, but...

Feb 25, 2009 | 2004 Dodge Ram 2500

1 Answer

1998 Dodge Ram 1500 4WD blowing fuse when turning left signal on


left side u got a short
u can wire up a buzzer or light to plug into where the fuse goes that blows when u turn on ur left blinker the buzzer will sound or the light will come on ,while the buzzer is on take apart left signals
and check wiring by moving harness around ,when u find the short the buzzer will quit

Jan 21, 2009 | 1998 Dodge Ram 1500 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...