Question about 1988 Honda Accord 4 Door

1 Answer

How do I replace my 88 Honda Accord front right fender?

How do I remove and replace my front right fender on my 1988 Honda Accord LXI (2 door)?
Also, due to the impact on the fender, it popped the crank bolt on the right frog light. So the headlight doesn't go up and down.
Hope someone can help with these two projects.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 68 Answers

Scrap it

Posted on Dec 07, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

88 honda accord lxi hard time starting like it not getting gas but when it starts at high idle it will run ok and then it will die


CHANGE AIR FILTER AND FUEL FILTER THEN CLEAN FUEL INJECTORS,CHECK SPARK PLUGS SEE IFTHEY ARE BLACK SOOT ON THEM.MORE LIKELY SPARK PLUGS GETTIN FOULED OUT DUE TO CLOGGED LEAKING FUEL INJECTORS.CLEAN FUEL INJECTORS.POUR BOTTLE OF SEAFOAM TO 3/4 TO FULL TANK OF GAS

Jul 16, 2011 | 1988 Honda Accord 4 Door

1 Answer

Where is the pcv valve located on a 88 honda accord Lxi, fuel injected? i'm trying to replace it and can't seem to locate.


Follow the large (3/8 in) PCV vacuum hose from the front of the intake manifold plenum (lg silver box with label PGM-FI ). It turns toward the pass. side then down between intake maifold tubes/runners to the PCV valve.

Oct 04, 2009 | 1988 Honda Accord 4 Door

1 Answer

1988 Honda accord


have you checked fuses ? has it a immobilizer ? have you try jump starting it with another car with jump leads ?

Jul 14, 2009 | 1988 Honda Accord 4 Door

1 Answer

1988 Honda Accord LX blinker switch short?


yes switch is bad replace it pull cover off from around steering collum should be screws holding it on you may haveto pull steering wheel but haven't done one in solong i can't remember

Jun 28, 2009 | 1988 Honda Accord 4 Door

1 Answer

88 Honda LXi...starts then dies, restarts then dies.


just check the fuel pump is connected right also the fuel filter other than that it could be a blockage in one of the fuel lines the filter should have an arrow printed on it point it out hope this helps regards Jim

Mar 26, 2009 | 1988 Honda Accord 4 Door

1 Answer

I cant find the fuse for the cigarette lighter on my 1988 honda accord LXI


its under your dash, usally it says dash/dome lights or radio

Mar 23, 2009 | 1988 Honda Accord 4 Door

1 Answer

1988 acccord turn signal acts like light is blown


Check the earth to the offending light unit. Clean all the relevant connections. You could also try fitting a temporary earth cable and watch for any improvement. If you find that there is improvement in the operation of the indicator/flasher make the temporary earth cable permanent.

Nov 26, 2008 | 1988 Honda Accord 4 Door

2 Answers

88 honda accord lxi 2.0 fuel injected (high idle)


hello i would test your( tps) throttle position sensor some part stores will test for you .goodluck

Aug 10, 2008 | 1988 Honda Accord 4 Door

2 Answers

88 Honda Accord left front turn signal assembly


*The Turn signal on the Side of the car next to the headlight*
1. Open the retractable headlights.
2. Remove the plastic shroud around the headlight: two screws in front and one on each side.
3. Look to the outside of the headlight and you will see a single screw in a small plastic cover on the front inside edge of the signal light assembly. The headlight prevents you from getting at the screw straight-on. I broke it loose with an offset phillips screwdriver, and then backed it out with a regular phillips.
4. Remove the plastic cover, and you will see two screws. Remove them.
5. Now you can pull the turn signal assembly forward and out.
6. To remove the bulb holders from the assembly, twist counterclockwise and pull out.
7. Pull straight outward to remove the bulbs. To assemble, follow the steps in reverse. Note that there are two plastic rods on the back end of the turn signal assembly that you will insert into two holes in the channel of the fender

*The turn signal in the bumper*
1. You will need a phillips head And Flat head screw driver, right below the turn signal there is a panel that you can pop out, (or its allready gone, Looks like a Fog light can go in there.)
2. once u find that, (Pretty easy to find) Look directly up in there., there is styrofoam up there and u will also notice a little hole,
3. Stick the Phillips head screw driver in that hole and turn it counter clockwize, The screw will not fall out,
4.once it feels like the screw is loose put the flat head in between the turn signal lense and bumper, the side where you unscrewed it and SLOWLY pry it out,
4. once out, just twist the plug and replace light bulb
to replace just reverse instructions

Jun 29, 2008 | 1988 Honda Accord 4 Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

374 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...