Question about 1986 Pontiac Sunbird 2 Door

1 Answer

Sllonide wont engage power syolnide car starts for 1 second then quits

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 23 Answers

Related to key problem call locksmith reprogram key or try original key

Posted on Jun 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 2006 chevy hhr suddenly wont start or crank about a week ago i did have a problem with power steering going out and had to drive it home like that but it now works


Can you hear the starter try to engage ?
Do the lights work ?
Have you tried cranking it in neutral ?
If the starter engages but won't turn the engine, and the battery is good, the power steering pump could have failed and that is locking up things. Removing the belt would tell you if the pump is the problem.

Mar 19, 2016 | 2006 Chevrolet HHR

1 Answer

Cruise control wont engage after restarting vehicle


The fact that the light comes on is a good indication that the electronics are working, the most common problem is a vacumn leak. This can be a damaged or cracked vacumn line, a bad check valve, or the dump switch on the brake pedal

Mar 28, 2015 | 2008 Buick Lucerne CX

1 Answer

Ford falcon wont start


pull the starter and fix the solenoid or replace the solenoid. It is engaging the armature with out engaging the pinion into the ring gear or the pinion override clutch is failed. Have a reputable auto electrician check it on the bench

Dec 07, 2013 | Cars & Trucks

1 Answer

My 1988 k1500 4x4 the four wheel drive is not engaging


There is an acuator in the front diff the are common to quite in late 80 to early 90 Chevrolet's / GMC

Oct 29, 2012 | 1988 Chevrolet K1500

1 Answer

2001 Chevy Malibu the car cranks but wont start I can hear the whine of the fuel pump coming on when I engage the ignition switch to on position, I can prime it and it will run for a few seconds...


sounds like a security problem-if the light is flashing leave the key turned on for about 10 min. until light stops flashing and then try to start engine-if this works you need to replace the pass loc sensor(ignition cylinder and housing)

Aug 18, 2010 | 2001 Chevrolet Malibu

1 Answer

85volvo 240dl wagon, transmission wont engage at all


The whining noise you are hearing is the pump starving for oil, due to a clogged filter. If you drove the car as you sadi for a week, with nothing but third, and it quit moving, you have severly damaged the transmission, and will be looking at either an overhaul, or replacing it.

Dec 03, 2009 | 1984 Volvo 240 Series

1 Answer

Starts, then quits after 2 or 3 seconds


If the engine keeps running when the starter is kept engage, it is an ignition switch problem but in this case it looks to me as an ECM problem.

May 11, 2009 | 1991 Suzuki Sidekick

1 Answer

1998 buick lesabre wont start


Do you have a Chip in the Key? if so that Could be the Problem,Ya see the chip is a resistor and if it looses its ELECTRONIC VALUE in its Case Resistance it wont start to test this Turn the Key in the ON posission then do the Screwdriver thing If it Starts Key is Good and Most Likely the Ignition (SWITCH) is Bad <<ELECTRICAL Side NOY LOCKEST SIDE For More Info Recontact Me
rejakwilson@aol.com<<<<<<<<<<<<<<<

Dec 23, 2008 | 1998 Buick LeSabre

1 Answer

2006 toyota corolla


Remove the starter & inspect the contacts inside the starter solenoid housing. If they are burnt and/or worn, you will get this condition. Replace the contacts and the plunger, or replace the starter. I change contacts in my shop 3-4 times a week. Quite a common failure. The clicking noise is the plunger hitting one contact, but not the other, due to wear.

Aug 23, 2008 | 2006 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...