Question about 2005 Ford E-Series

1 Answer

How to remove the fan clutch on a 6.0 diesel

How to remove the fan and fan clutch on a 6.0 Ford 2005 E350 diesel engine? 4,570,000 miles. Need to replace the vacuun pump.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Remove the air cleaner assembly.
  4. Disconnect the radiator upper hose from the radiator. Position the radiator hose aside.
  5. Disconnect the overflow hose from the radiator.
  6. Disconnect the coolant degas bottle hose from the shroud.
  7. WARNING The clutch assembly nut has a right-hand thread and must be rotated counterclockwise to remove it.how to remove the fan clutch on a 6.0 diesel - 31a3ca2.gif
  8. 95f52a2.gifUsing the special tools, loosen the fan clutch.
  9. Carefully rotate the fan and fan clutch assembly counterclockwise until the assembly is free from the water pump. Place the fan and fan clutch into the shroud opening.
  10. If equipped, disconnect the retaining clips from the fan shroud.
  11. Raise and support the vehicle.
  12. Disconnect the lower radiator hose retaining clamp from the shroud.
  13. If equipped, disconnect the underbody splash shield from the shroud.
  14. Lower the vehicle.
  15. WARNING Use extreme care when removing or installing the fan, fan clutch and shroud. Failure to do so will cause damage to the radiator.
  16. Remove the mounting bolts, and the fan, fan clutch and shroud.
  17. To install, reverse the removal procedure. Install an appropriately sized worm drive-type clamp in place of the constant tension clamp. Observe the tightening torques shown in the accompanying illustrations.

Posted on Jun 20, 2009

  • chris
    chris Apr 12, 2014

    at step 8 you say "special tools" could you be more specific

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the A/C clutch on a 2005 Ford E350 , 5.4 engine


Usually I replace the a/c compressor with a new one that has the clutch on it.

I do remember seeing a number of bolts holding the clutches on though.. never bothered to take it off though.

Clutches rarely go bad, but compressors leak.
If you have a slow compressor leak, you should replace the whole compressor with clutch.

I did find the following article on the Internet:

http://bernardembden.com/xjs/comclutch/index.htm

Jul 22, 2010 | 2005 Ford E-Series

1 Answer

How do you install a water pump in a ford f 450 6.0 ?


6.0L Diesel Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. With the vehicle in Neutral , position it on a hoist.
  3. Remove the radiator and shroud assembly.
  4. Disconnect the cooling fan electrical connector. Unclip and position the fan wiring aside.
    NOTE Use a hole in the fan hub to prevent the fan from turning.
  5. Using the hub tool, loosen the cooling fan and clutch.
  6. Remove the cooling fan assembly.
  7. Remove the stator bolts and the stator.

    8ac47ee.jpg
    Fig. Remove the stator bolts and the stator-6.0L Engine
  8. Rotate the accessory drive belt tensioner clockwise and position the drive belt aside.
  9. Remove the bolts and the coolant pump pulley.
  10. Remove the bolts and the coolant pump.
  11. Remove and discard the O-ring seal.
  12. Clean and inspect the coolant pump mounting.

    3ed0f4d.jpg
    Fig. Water pump mounting-6.0L Engine
  13. To install, reverse the removal procedure.
  14. Observe the following torques:
    Stator bolts: 30 ft. lbs. (40 Nm) Pulley bolts: 23 ft. lbs. (31 Nm) Water pump bolts: 17 ft. lbs. (23 Nm)

Hope this help.

May 15, 2010 | 2005 Ford F 350 Super Duty

1 Answer

Info. on 1986 ford diesel engine


Your fuel pump would be located in the gas tank. It is mounted on the pick-up tube/sending unit assembly.

Sep 29, 2009 | 1986 Ford F 350

1 Answer

I have a 1999 E350 7.3 turbo diesel that only has approx.30,00 miles on it. Last week the service engine soon light came on after getting about 2 miles down the road and then started to run rough. It...


Take it to a shop that specializes in diesels or fords. they will be the best qualified to help you. You did good by replacing the fuel filter, that would be one thing they would want to replace anyhow.

Sep 26, 2009 | 2002 Ford E350

1 Answer

1994 ford E350 E40D trans/7.3 diesel Shifts great and after 2 miles seems to shift back and forth between 2nd and 3rd gear. seems the lock up engages and dis engages. Any ideas? changed out the MTPS?...


the solenoids in the trans may be sticking,try adding 1 pint of dot 3 brake fluid to the transmission fluid and drive it for a while-give it a chance to work..the brake fluid acts like a cleaner and it makes worn seals and clutches swell a little.just drive it easy for about 20-30 miles,its only about $3.00 and it could save a $1,600.00 rebuild

Aug 10, 2009 | 2004 Ford E250

1 Answer

Starting system wiring diagram for a 86 ford e550/100


Have you located your local Cummins Dealer for this. It should be no issue for them to copy/email a diagram. Good luck...

Jul 13, 2009 | 1986 Ford Econoline

1 Answer

Replace thermostat on Ford e350 diesel 1990


follow top hose from radiator to engine, it connects to steel tube with a plat and 2-3 boltshold plate down. sypgon radiator down into clean bucket, remove bolts, take out thermostat, clean both mounting surfaces very clean until only metal showing put in new thermo put gasket on tighten bolts and add antifreeze

Jul 06, 2009 | Ford E-350 Cars & Trucks

Not finding what you are looking for?
2005 Ford E-Series Logo

4,674 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...