Question about 1996 Dodge Dakota

2 Answers

I can only locate (1) speed sensor on trans

I can only locate (1) speed censor on trans mission ,I was told there were two , I can let it warm up for 15 min. And when I take off in drive
it will spit and sputter until I put it in nuetral, I have to shift it manually.
code says "no signal from speed sensor"

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Dodge Master
  • 813 Answers

The other sensor is on the side back half way up just to the right of the first one about foot back

Posted on Dec 02, 2011

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 32 Answers

Look on the rearend above the pinion.

Posted on Jun 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced speed sensor in a 1994 Lebaron. Speedometer still not working. any suggestions?


Well it could be the drive gear in the trans or the speedo in the dash.

Apr 07, 2016 | 1994 Chrysler LeBaron

4 Answers

My car doesn't seem to want to go out of first gear


Check vehicle speed sensor, or ABS wheel speed sensor,
and the wiring going to sensors.Speed sensor should be on side of trans mission.

May 06, 2015 | 1997 Ford Escort

1 Answer

Location of trans speed sensor 3 pin location 2004 solar v6 automatic p0500 speed sensor trouble code


no what matters is if the pulses are good.
and the transmission not slipping.
the TCM is not genious level yet.

are you asking what P0500 means.
or want us to tell you all things stated in fSM for this code.
what? guessing you can do .
ever heard of alldata.com (DIY)
ever read that page on 500s?
i guess not.
3.3L v6 ?
quote:
Trouble Code Conditions: P0500
VEHICLE SPEED SENSOR "A"
The ECM detects following conditions simultaneously for 2 secnonds (1 trip detection logic):
No SPD (speed sensor) signal while ECM detects NC (trans­mission counter gear) signal is more than 300 RPM Park/Neutral position switch is OFF (When shift lever is in other than P and N positions) Possible Causes:
  • Open or short in speed sensor circuit
  • Speed sensor
  • Combination meter
  • ECM
  • Skid control ECU
im trying to decode that too, the sensors
are called, C3 counter gear sensor, and Turbin T3 sensor
but the book keeps changing names in the book.

i think it means, counter gear shows correct RPM
but the turbine gear sensor T3 is dead.
while in gear. is too hard for them to say. so i said it.
and my guess, moving,
after all transmission slip moving
in fact i can scan your car and prove that
i scan it in park, then indrive, no moving
got 500s, or are 500 happening flogging engine.

but the ECU signal is either dead for turbine sensor or is way too slow. see incongruity from 300+ rpm on counter gear.

500 means dead, not intermittant.
i looked at all codes for turbine.

so my best guess (no real fsm only alldata)
is Turbine is the clutch sensor. (input rpm to trans-clutch)
and counter gear is tail shaft sensor.? (output speed)
so the front clutch sensor is dead
or being grounded out, or is not connected, (rusty conns?)

Most FSM made do a poor job, at showing possible bad parts.

here is better
  1. the sensor is weak or dead
  2. the sensor connections are bad.
  3. the sensor, signals do not arrive at the PCM /TCM, due to bad wires, or anything on that line shorting that line out.
  4. better (yes?, this is electronics) no a parts swap game.

if the car drives ok then the trans does not slip.
the TCM sees both ends and can detect, bad sensors or gross slip.
i think it means bad sensor. in this case only.

what does this mean?
  1. having difficulty locating it
can buy one, find one, can't insert it, or?

Feb 13, 2015 | 2004 Toyota Solara

1 Answer

6spd 08 ford transit all gear work except 3rd no noise just no drive in 3rd gear what is the problem


could be a trans speed sensor. trans mission could also need flushed and the filter replaced.

Nov 29, 2014 | Ford Cars & Trucks

1 Answer

How to change a speed censor on a 2004 intrepid


Wheel speed or trans turbine speed sensor?

Jul 22, 2014 | 2004 Dodge Intrepid

1 Answer

Where is the input and output sensors on a 99 plymouth breeze 2.0 ltr


Yes you will need to remove several components in the drivers front area of the engine compartment to get at the speed sensors. You may need to remove the battery as well as the battery tray. Computers may also be in the way. The trans cooler hoses will need to be removed from the teams mission to replace the input speed sensor.

Mar 08, 2012 | 1999 Plymouth Breeze

1 Answer

Trac light, anti brake light and service soon light goes on and i am told a bad censor is causing that. is it still safe to drive


Sounds like bad speed sensor. Will probably loose speedometer also. Should get scanned as soon as possible to locate problem.

Jun 30, 2010 | 2000 Oldsmobile Intrigue

1 Answer

I have a 1996 dodge caravan with the 3 speed transmission and i need to find out the exact location of the input and output speed sensors thanksi


A 3 SPD TRANS DOES NOT HAVE INPUT/OUTPUT SENSORS..ONLY A VEHICLE SPEED SENSOR..IT IS LOCATED ON TRANS EXTENSION HOUSING WHERE RIGHT SIDE AXLE COMES OUT OF TRANS..1 BOLT AND A WIRE CONNECTOR

Jul 18, 2009 | 1996 Dodge Caravan

1 Answer

Speed sensor


IT IS ON THE OUTSIDE OF THE TRANS WHERE THE SPEEDO CABLE USED TO GO. HERE IS A PICTURE

48cc8be.jpg

Aug 21, 2008 | 1989 Dodge Dynasty

Not finding what you are looking for?
1996 Dodge Dakota Logo

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...