Question about 2006 Hyundai Sonata

1 Answer

How do I replace the high mount brake light on my 2008 sonotas?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 776 Answers

Already described

Posted on Jun 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 lincoln navigator shifter locked no brake lights is there a way to test the brake switch


Yes , with a volt meter . Find the switch an back probe wires ,testing for voltage in , then press the brake pedal an check for voltage on wire going out . You'll need a wiring diagram so you know which wire is the right one's . You can find free wiring diagrams at http://bbbind.com/free_tsb.html enter vehicle info . year make model an engine size .Under system click on lighting ,then under subsystem click on stop lamp . none of the brake lights work including the high mount stop lights ? A electronic module (smart junction box) controls the lower brake lights . The high mount are controlled directly from brake light switch .

Sep 25, 2016 | 2008 Lincoln Navigator 4x4

1 Answer

Left Hand only SIgnal and Brake lights on a 2008 chev 3500 cutaway not working


Turn signal/ multifunction switch. Replace it. All the exterior lights run threw it except the high mount brake light. Check the brake lights. If the high mount works and the others don't . That is a sure sign.

Sep 06, 2016 | Chevrolet 3500 Cars & Trucks

1 Answer

Brake light stays on and beeping while drivig


Year make and model helps, But, look at the lights. Are the tail/brake lights on, but not the high mount brake light? Replace the turn signal switch in the column. If the high mount is on. It could( most likelyy) be the brakes switch at the brake pedal. Could also be a shorted wire to power.

Jul 08, 2016 | Cars & Trucks

1 Answer

Where is the tail light fuse?


The tail light fuse is under the rear seat on the drivers side.

Jan 17, 2016 | 2003 GMC Envoy

1 Answer

Brake lights Inop.


Check the brake relay for loose connections. And the light fittings for a loose earth.

May 21, 2013 | 2008 Jeep Commander

1 Answer

I put new bulbs in both brake lights and high mount light . brake lights work not the high mount light.


More than likely the sockets in the high mount are burned, replace them..

May 25, 2012 | Cars & Trucks

2 Answers

Wondering how to change the third brake light (one located in back window) on a 2006 hyundai sonata


High Mounted Stop Lamp Removal & Installation To Remove:
High Mounted Stop Lamp hyundai-06-00-5896.gif

  1. Disconnect battery negative cable.
  2. Disconnect high mounted stop lamp electrical connector from inside trunk.
  3. Remove package tray.
  4. Replace bulb from package tray.
To Install:
High Mounted Stop Lamp hyundai-06-00-5896.gif

  1. Install package tray.
  2. Connect high mounted stop lamp electrical connector from inside trunk.
  3. Connect battery negative cable.
prev.gif next.gif

Oct 12, 2010 | 2006 Hyundai Sonata

1 Answer

How do i change a brake light bulb on 2000 vw jetta?


Removing:
  • Switch off all electrical consumers, switch off ignition key and remove ignition key.
  • Remove rear luggage compartment side panel trim (left or right).
98971821.gif
  • Remove 3 nuts, arrows, and remove housing.
  • Remove bulb holder.
Installing:
  • Install bulb holder.
  • Insert housing into body opening.
  • Tighten nuts.
  • Install applicable rear luggage compartment side panel trim.
Rear Light Bulb Holder Removing And Installing:
Removing:
  • Disconnect electrical connector.
  • Depress retainers, arrows, and remove bulb holder.
98971817.gif Installing:
  • Install in reverse order of removal.
And the Center Mounted Brake Lamp.
High mount Brake Light Removing And Installing:
The high mount brake light is installed in the rear shelf.
98971288.gif Removing:
  • Switch off all electrical consumers, switch off ignition key and remove ignition key.
  • Disconnect electrical connector from high mount brake light.
  • Remove rear shelf
  • Un-clip high-mount brake light from rear shelf, arrows.
  • Install in reverse order of removal.
NOTE: The bulb holder base plate contains soldered- in light emitting diodes (LEDs) that are not replaceable. In the event of LED malfunction, replace complete bulb holder.
Additional

Mar 13, 2010 | 2000 Volkswagen Beetle

1 Answer

1999 GMC Envoy: replaced both GE 3057 lamps in left rear light assembly. Lamps both light. However depressing brake pedal does not initiate brake light. The righ rear brake light does work. The high mount...


The high mount brake light has its own fuse, so check that first. The high mount bulb is generally a stabdard type (there may be more than one bulb) or you can replace with an LED. As for the left rear bulbs not working when depressing brake pedal, check the bulbs again for any spring that may be broken. If the bulbs are still good, make sure there is sufficient contact with the socket. If still not working, have someone check it out further.

Feb 15, 2010 | 1999 GMC Jimmy

1 Answer

Replaceing brake lights on the trunk assembly part, how do i get to the lights?


High-Mount Brake Light NOTE: Depending upon the vehicle, the center high-mount brake light may be accessed from outside the vehicle, through the trunk, or through the passenger compartment.
  1. Remove the center high-mount bracket light lens retaining screws.
Fig. 17: Use a screwdriver to unfasten the center high-mount lens retaining screws . . .

0379160.jpg
Remove the lens in order to get to the bulbs.

Fig. 18: . . . then remove the lens for access to the bulbs

c49ad34.jpg
Carefully pull the bulb away from its retaining clip contacts.

Fig. 19: Pull the light bulb from the retaining clips

e0d87c6.jpg
Installation is the reverse of the removal procedure. Before installing the lens, make sure the brake light operates properly by having an assistant depress the brake pedal.

Jul 26, 2009 | 1999 Pontiac Bonneville

Not finding what you are looking for?
2006 Hyundai Sonata Logo

452 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...