Question about 2000 Ford Expedition

1 Answer

R134A Where is it under the hood for me to put in the R134A!!!!!!!! I see one spot but the end of my hose want fit there. Is the other end in site?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 414 Answers

What year is the car, is it retro fitted for 134?
Follow the A/C lines to other side of compressor try the fitting there. Other wise an adapter is available.

Posted on Jun 20, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What kind of ac coolant does it have 134a or r 12 and where is the low pressure port for the ac located

Depends on the year. Cars in the early 90's used R12. Anything later uses R134a. The size of the charge ports will define the R134a port. An adapter is needed to fit on the charging hose. R12 requires no such adapter. Ther charging label under the hood will tell you what refrigerant is needed too. Since you failed to give enough information on what make and model car you have, a general answer for the location of the low pressure port will be given. On the compressor, the larger diameter hose connection is the low side. Connect there, or look for the drier/accumulator (Large diameter silver container near the firewall). Connect there. You will need to access the AC information label under the hood to determine how much freon to add to the system.

Mar 12, 2016 | AC Cars & Trucks

1 Answer

Where is the low air pressure port on a 2004 Suzuki verona

on what?
is this a TPMS question, tire monitors?

all you said are and ment Freon (or A/C Refrigerant)
HVAC answers. (low pressure side, is large pipe)
there are 2 ports. each a different size. (big is it)
the tool in hand the Freon R134a can and hose.
has but one fitting (walfart setup)
you look under hood. and see, the 2 big lines on compressor
its just 2 lines.
the one big line on the compressor is that line. Lowside.
and to fire wall it goes, and fitting,
on the way are 2 fittings, only one fits the hose.
they have caps.

here is a generic site, showing the same trick.
the walfart gauge only has 1, on left. low side


Aug 22, 2015 | Suzuki Cars & Trucks

2 Answers

I am trying to put R134A in my car, and I wanted to make sure I put it in the low side service port, but I am having problems figuring out which one is the low side service port

The R134A connection hose will only fit on the low side service port. The high side port is bigger and will not fit that hose.

Jul 05, 2011 | 1998 Nissan Sentra

3 Answers

Recharge air conditioner where is the valve located that allows me to recharge the air conditioner

i belive on this year car and make its located under the air filter box, remove the intake hose then the cover for the air filter, remove the filter then remove the lower part of the air box there you will see the filter dryer and the lines coming off the dryer and there will be two fittings to charge the ac system, the smaller fitting is the low side this is the side to charge through, make sure not to overcharge the system and add oil as needed, a good idea is to add dye to the system to help in finding the leak if system goes low again, theres a decal under the hood or on the dryer that tells you how much freon the system can hold. if you under or overcharge the system the air may be cold but future ac damage is for sure, good luck.

Jul 10, 2010 | 1998 Chevrolet Lumina

1 Answer

Where do we put freeon for the air conditionner

There are only 2 fittings on your ac system. The low side is the one you put in refrigerant (r134a). It is the smaller sized fitting usually located on low side hose that connects to receiver dryer (looks like a can on passenger side firewall). The quick connect fitting on any recharge hose will only fit on this correct fitting. The other one (high side) is too large to fit. So you cant put it in the wrong one.

Jun 06, 2010 | 1994 Lincoln Town Car

2 Answers

AC needs a charge and how do I take the inside door panels off?

the a/c fitting are under the hood. they should be along the passenger side of the motor near the fire wall. don't put any r134a with sealant in it. only pure R134A.

Aug 06, 2009 | 1996 Lincoln Town Car

3 Answers

Where do I get instructions on how to recharge the air conditioning on my '96 Isuzu trooper?

if you have a 134 hose the fitting on the hose fits on only one fit look under the hood and you can find two fitting with a blue or green cap remove the smallest cap and connect the hose with a can of freon 134 with the engine on and the AC on try one can then check if the AC is blowing cold if not put in one more can

Jul 24, 2009 | 1999 Isuzu Trooper

3 Answers

R134a recharger nozzle won't fit on low pressure service port.

The low pressure port on the 2003 grand am is actually behind the engine, near the firewall on the passenger side. Good luck getting your hose down there though, I ended up buying an extension hose.

Jul 24, 2009 | 2004 Pontiac Grand Am

2 Answers

On my 1995 chevy blazer s-10 my face vents are not blowing air

Your heater valve is stuck open, also in a pinch you can crimp off your hose to the heater coil at fire wall. Try to find the heater valve vacumb hose under the hood see if it is bad and fixit. or some models have a cable to the valve could be broken. 

Jun 02, 2009 | 1995 Chevrolet Blazer

1 Answer

Installing pin on hood on '93 mustang

if the spot under the hood is flat then u can slightly enlarge the holes for the hood plates and even the they will be at an angle the pins will still be straight and will still fit my 78 z28 track car was the same way the whole hood is contoured and it worked great

May 22, 2008 | 1993 Ford Mustang

Not finding what you are looking for?
2000 Ford Expedition Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

81294 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

gerry bissi

Level 3 Expert

4376 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides