Question about Ford Bronco

1 Answer

How to remove tailgatein 89 Bronco

Husband had an accident. The window was broken out and the tailgate all bend to hell. Need too know how to take the tailgate OFF of 2 broncos to switch them.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 115 Answers

A Bronco tailgate comes off the same as a regular pickup truck. Open the tailgate and remove the cables from both sides. Lift up the passenger side of the tailgate and then slide the driver side towards the passenger side.

Posted on Apr 25, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 508 Answers

SOURCE: remove dashboard on a 88 ford bronco 2

You don't need to remove the dash. Look under the dash where the switch is located. on the side of the switch you will see a small button to push in. While pushing in on the button pull the knob as though you were going to turn the lights on. At this time the stem should release from the switch. Undo the bezel and drop the switch down so you can see to unplug the wires. Replace wires to new switch and reverse the procedure to install. You don't need to push the button in when replacing the stem.

Posted on Feb 07, 2009

  • 59 Answers

SOURCE: replace motor on tailgate window on a 1987 ford bronco

You will likely have to remove the panel from the inside with the window up. Once you have the panel off I would try to have some one hold down on the switch while you tap the motor with a hammer. Of course make sure the latches are all the way closed as if the door is not closed all the way the window will not roll down as it has safety switches to keep this from happening.

If you still can not get it down then you will need to unbolt the regulator and let it down that way.

Posted on Feb 23, 2009

  • 3 Answers

SOURCE: Bronco rear window was being rolled up with a key

The electric key switch is next to the key cylinder on the rear door. You can see it easily with the window down and weatherstripping pulled out. The wiring may have become chaffed with the window over the years or the switch corroded in the contact points inside.

Posted on May 11, 2009

wlightaul
  • 29 Answers

SOURCE: The tailgate window on my 92 Ford Bronco won't go

check the safety switch in the tailgate either on the bottom of the handle or the drivers side latch if it is bad you can run a jumper wire

Posted on Nov 28, 2009

  • 1 Answer

SOURCE: Fuse panel diagram for 1990 ford bronco 2

Here's the diagram for the fuse panel under the dash. There is also a fuse panel under the hood next to the air filter.e589aae.jpg

Posted on Jan 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1989 FORD BRONCO. REAR WINDOW STUCK IN UP POSITION AND MOTOR IS DEAD. HOW DO I GET THE WINDOW DOWN SO THAT I CAN DROP THE TAILGATE?


you have to climb over back seat and pull panel off tailgate pull the motor out and let window down by hand .

Sep 16, 2012 | 1989 Ford Bronco

1 Answer

Have a 1992 Ford Bronco Eddie Bauer Tailgate window motor problem


I looked at my schematics, and they don't show a relay. They do, however, show two ground wires coming out of the tailgate window switch. There is a ground wire for the "up" side of the switch, and a ground wire for the "down"side. These would be color-coded black, and I think that it is worth checking to make sure you don't have a corroded /broken ground running from the tailgate switch. If only one grounding wire was broken, the window would operate in only one direction. Both dash and tailgate switches share the same wiring circuit, and these wires are "hot" all the time. It's normal when you get both sides of the motor leads at 12VDC when neither switch is activated. These switches function by switching off one of the two motor leads, and connecting it to ground, thus allowing power to flow thru the motor windings. Of course, reversing the polarity on a DC motor will change the direction of rotation, so changing which black lead is switched to ground gives the up or down direction to the motor.. since you can read schematics, you might check out ebay for a used Haynes manual cheap. hope this helps

Apr 29, 2010 | 1992 Ford Bronco

1 Answer

How do you remove the rear window motor in the tailgate of my 89 ford bronco. I took off the inside panel to be able to see the inside but from there don't see the motor and how to get further into the...


there is about 3 rivets that you have to cut off,that holds the window motor and regulator to the tailgate,then shift the window back and forth to get the track slides to slide out then pull the window out slowly,it will catch when its almost out so be careful.

Nov 13, 2009 | 1989 Ford Bronco

1 Answer

Need to replace the tailgate release assembly


yes the clips on each end snap away from the rod then the rod pulls up thats it.

Jun 25, 2009 | 1996 Ford Bronco

2 Answers

The tailgate window on my 92 Ford Bronco won't go down. No indication of power. The fuse checks ok. There is no visible sign of broken wiring. (at least it failed in the "up" position). Thanks!


check the safety switch in the tailgate either on the bottom of the handle or the drivers side latch if it is bad you can run a jumper wire

Jun 07, 2009 | 1992 Ford Bronco

1 Answer

Tailgate window doesnt work


It could be several things. Make sure the tailgate is latched all the way. The motor could be bad. remove the tailgate cover inside the truck. use a test light and have someone press the up and down button while checking for power at the motor wiring. If you have power going to motor on both sides ,the motor is bad. If you do not have power check for broken wiring or bad switches.

Feb 01, 2009 | 1993 Ford Bronco

1 Answer

Replace motor on tailgate window on a 1987 ford bronco


You will likely have to remove the panel from the inside with the window up. Once you have the panel off I would try to have some one hold down on the switch while you tap the motor with a hammer. Of course make sure the latches are all the way closed as if the door is not closed all the way the window will not roll down as it has safety switches to keep this from happening.

If you still can not get it down then you will need to unbolt the regulator and let it down that way.

Jan 14, 2009 | 1987 Ford Bronco

5 Answers

Rearwindow/ door


if there are no broken wires inside the tailgate try lubing the latches with WD40 and open and close the tailgate several times. If the latches are properly closed on both sides the window will not work

Nov 29, 2008 | 1990 Ford Bronco

1 Answer

Tailgate window motor


You must detrim the tailgate and then remove the glass and then the entire regulator assembly must be pulled to change out the motor.

Nov 21, 2008 | Ford Bronco Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85108 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4387 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...