Question about 2003 GMC Envoy Xl

Open Question

The gear shift knob is loose and it will not shift from parki tried to tighten the screw but that did'nt work

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Impala gear shift button popped out. I have to put it back in each time I need to shift to D, R, etc. How can I remedy this problem without replacing the whole gearshift?


Re-attaching the knob to the gearshift is the key...Look for a hole on the lower section of the knob...if you cannot see it...remove the bottom chrome piece from the knob, (pry apart carefully not to scratch the chrome housing...you should see the small hole normally includes a small allen insert screw or Phillips screw...must be screwed in to the gear shift shaft to hold in place...if you cannot compare...visit a local salvage yard to experiment..."Pic A Part" is a national self help salvage yard. Hope this helps. If the button does not stay in the gear shift knob...you can replace the knob (with button) only...remove the knob as described above. Hope this helps.

Oct 14, 2013 | 2006 Chevrolet Cobalt

1 Answer

Gear knob tightening


under the cover leather or plastic push it down and you should find a 14 mm nut you loosen it off and turn the knob till in the proper position and tighten up the nut under neath it if this doesnt work take the knob off completly and put some glue on the threads or locktight and reinstall the knob let it sit for a hour before using it

Aug 10, 2012 | Kia Sorento LX Cars & Trucks

1 Answer

Tighten a loose gear knob


Get some lock tite glue and apply to the threads on shifter and screw knob on and let dry.

Aug 10, 2012 | Kia Sorento LX Cars & Trucks

1 Answer

Replace gear shifter knob on s-10 manuel


Most gear shift knobs are just screwed on. Try turning it anti clockwise if yu can not see any screw holding it

Jun 22, 2012 | Cars & Trucks

1 Answer

I have a '94 F150, straight 6, 4wd, 5 speed manual trans. My transmission shifting knob popped out of it's position and was stuck in a gear. I opened up the cover and was able to move the gear manually...


it seems like your shift fork is in between gears you must remove the shift tower and align all the shift levers then drop the shift knob into the middle being neutral tighten it up and it should be ok but remember the replacement could be slightly thinner then the original and causing this new problem.

Nov 13, 2010 | Ford F-150 Cars & Trucks

2 Answers

How to install new gear shift "knob" to 1995 jaguar xj6


My 95 XJ6 does not have the allen screw, all you need to do is get a good grip and turn it loose.

Jun 05, 2010 | 1995 Jaguar XJ6

1 Answer

I'd like to replace the stock shifter knob (or


Usually there is a nut on the bottom of a shift knob that needs to be loosened, then the knob just screws off. Use a wrench, if it's hexagonal, if it's just round or there is no nut it may just screw off. It will be really tight though, be prepared to have to really crank on it to get it loose. The new one should just thread back on. You may need to install a nut on the bottom to adjust the rotation of any pattern or gear shift diagram on the new one.

Nov 11, 2009 | 2007 Chrysler Crossfire Convertible

1 Answer

Shifter lever on steering will not go in gear tight, seems like has alot of play and real loose. how do I correct this problem


This may be similar to the full size Ford shifter. If so, if you can access under the steering column, there is a connection flange on the shift linkage, There are two allen screws attaching the shift lever with a matching flange that attaches to the remainder of the shift linkage. The screws may have come loose and /or fallen out. With a little bit of finesse you'll be able to reinstall and tighten the screws... this should tighten your shifter back up...

Nov 01, 2009 | 1999 Ford Ranger SuperCab

1 Answer

The floor shift to put automatic transmission in gear is loose.


you have to remove the console cover to get access to the bolts that hold the shift assembly to the floor. I think there are 4.

You probably have to remove the shift bezel cover (PRNDL), remove the shift knob to get the console off.

Jan 16, 2009 | 2003 Lincoln Aviator

3 Answers

Shifter sloppy, having trouble getting it into gear.


There is a bracket with two torx screws that gets loose. You need to tighten that. You will need to remove the plastic and metal shield under the dash, above the brake pedal to see the bracket. Look up above the brake pedal and wiggle the the shift lever and you will see what needs tightened. Worked for me.

Oct 01, 2008 | 1996 Mercury Grand Marquis

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

221 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...