Question about 2006 GMC Yukon Denali

1 Answer

2006 yukon engine light is on

Yesterday the engine light came up on my 2006 yukon only have a 1year with it did oil change yesterday too but still on

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 148 Answers

The engine light needs to be scanned with a scan tool to pull a code, with that code you can start to diagnose, check your gas cap, make sure its tight, other than that you need to get it scanned before we can help you further

Posted on Jun 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The local high school auto shop recently replaced the radiator in my 2006 Yukon and did not connect the oil lines correctly. The oil leaked out and the engine stopped.


A lot depends on how long the engine ran without oil. If the starter will still crank it, you might be lucky. If the engine has a lot of miles on it, it might be best to overhaul it, since rings and crankshaft bearings suffer the most .

Dec 04, 2016 | 2006 GMC Yukon

1 Answer

One cylinder piston has seized. can it be repaired? 2006 Acura TL (manual) V6


Bad news is it can be fixed but requires complete overhaul I'll bet. Swapping in used engine might be better, or crate engine if price is not important.

Apr 23, 2015 | Cars & Trucks

1 Answer

Yukon XL was first showing Reduced Engine Power, then Oil Gauge quit working, now car is running hot


Might help, disconnect negative terminal from battery for 10 minutes, if the compute is getting weird readings this will reset it and maybe help.

Dec 09, 2013 | 2005 GMC Yukon XL

1 Answer

Oil light comes on,low oil pressure, message says shut engine off now


HI, could be failure of the engine oil pump.. if you are still running around in the vehicle it might be the sensor on the engine block that is faulty, cause without oil pressure your engine will seize up and that's expensive.what about a good oil change and a nice new oil filter, could do wonders ?.good luck.

Mar 20, 2010 | 2006 GMC Yukon Xl Denali

1 Answer

HOW DO I RESET THE CHANGE OIL LIGHT ONCE THE OIL


look in the manual......turn the ignition to the on position not starting it of course and then pump the gas petal 5 times then the light will blink a few times turn off then back on...problem solved

Jan 30, 2010 | 2002 GMC Yukon Denali

2 Answers

2006 Yukon Denali, oil pressure gauge malfunction


Most likely the oil pressure sensor is bad. Its located in the very rear of engine on top of bell housing area.

Oct 30, 2009 | 2006 GMC Yukon Denali

1 Answer

Engine light on


the engine light needs to be scanned with a scan tool to pull a code, with that code you can start to diagnose, check your gas cap, make sure its tight, other than that you need to get it scanned before we can help you further

Jun 20, 2009 | 2006 GMC Yukon Denali

1 Answer

I have a 2006 gmc yukon and just had it for 1 year and the engine came on yesterday and did oil change but still on i thought that since i have 22,inch rims that was the problem


check owners manual for reset procedure. or try the key in on position so dashlights are on & holds gas pedal to floor or key on & pump gas pedal 3xs. or call dealer

Jun 20, 2009 | 2005 GMC Yukon

1 Answer

Service engine light staying on


Hello tdamm...No...the service engine soon (SES) light on your yukon is not telling you to change the oil.
This is a warning light that is illuminated when there is a problem affecting the Emission system and the engines computer management (ECM) has detected it from a fault. It could be something as simple as a loose or defective gas cap. If the SES light is blinking, it's more serious....
The yukon needs to be connected to diagnostic equipment (scanner) for fault diagnosis.
You can go to autozone they will hook up an OBD II scanner to your vehicle and explain the codes to you.
Good luck...i hope this helps and will fixya up.

May 25, 2009 | 1999 GMC Yukon Denali

Not finding what you are looking for?
Cars & Trucks Logo

469 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...