Question about 2002 Ford E350

1 Answer

How do i remove the rear brake drum on a 04 ford transit

The brakes have siezed on the nearside rear and i cant figure out how to get the drum off

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,674 Answers

If you can't get emergency backed off to allow for movement, then you'll have to get small pointed object (screwdriver or whatever) in adjustment hole to lift lever holding adjuster wheel, then back off adjuster wheel at same time until free. If it's emergency cables seized at backing plate area, try spraying where cable goes into sleeve with penetrating spray, and rap sleeves of cables going into backing plate with a stick, or screwdriver handle and it may help them retract enough to loosen up shoes in drum. Good Luck.

Posted on Jun 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove Brake Drum


Open bleeder nipple to release some pressure off the shoes .

Oct 07, 2017 | Ford Cars & Trucks

1 Answer

Where the hell can I get a FREE PDF download for my Ford fusion 2 for the removal and replacement of the rear wheel bearings as well as the torque settings for the final nut after replacement.All the so...


Rear Suspension - Rear Wheel Bearing Fusion 2002.75 (06/2002-)

-Removal and Installation

Special Tool(s)

Installer, Differential Bearing
205-062

Installer, Input Shaft Seal
307-210 (17-041)


General Equipment
Soft faced hammerWooden block

Removal

CAUTION: The brake drum and hub assembly removal in this procedure is for installing a new wheel bearing, not for access to brake system components.

-All vehicles

Remove the dust cap.
Remove the wheel and tire.
For additional information, refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

-Vehicles with rear drum brakes
Release the parking brake.
Remove the brake drum and hub assembly.
Remove and discard the wheel hub retaining nut.


-Vehicles with rear disc brakes
Remove the brake disc.
For additional information, refer to in this section.

Remove the wheel hub.
Remove and discard the wheel hub retaining nut.


-All vehicles

Remove and discard the wheel speed sensor ring (brake disc shown).
Remove the circlip (brake disc shown).
Using the special tool, remove and discard the wheel bearing (brake disc shown).

-Installation

-All vehicles

CAUTION: Support the wheel hub assembly on the wheel mounting face and not on the wheel nut studs.

Using the special tool, install the new wheel bearing (brake disc shown).

Install the circlip (brake disc shown).

CAUTIONS:

Make sure the wheel speed sensor ring is not knocked, damaged and kept free from metal fragments.

Protect the face of the wheel speed sensor ring with a non-ferrous flat block to prevent damage.

Make sure the wheel hub or brake drum is adequately supported and do not allow it to rest on the wheel studs..

Make sure the wheel speed sensor ring is pressed on slowly and squarely until fully seated.

Do not exceed a maximum load of 10 kN.

Using the special tool, install a new wheel speed sensor ring (brake disc shown).

Vehicles with rear drum brakes

CAUTIONS:

Avoid impact on the wheel speed sensor ring.

Make sure the wheel speed sensor ring is clean.

Avoid any contact between the wheel speed sensor ring and a magnetic surface.

Rotate the wheel hub assembly 10 times counter-clockwise when tightening the wheel hub retaining nut to prevent damage to the wheel bearing.

NOTE: Install a new wheel hub retaining nut.

Install the brake drum and hub assembly.
Apply the parking brake.

-Vehicles with rear disc brakes


CAUTIONS:

Avoid impact on the wheel speed sensor ring.

Make sure the wheel speed sensor ring is clean.

Avoid any contact between the wheel speed sensor ring and a magnetic surface.

Rotate the wheel hub assembly 10 times counter-clockwise when tightening the wheel hub retaining nut to prevent damage to the wheel bearing.

NOTE: Install a new wheel hub retaining nut.

Install the wheel hub retaining nut.
Install the brake disc.
For additional information, refer to in this section.


-All vehicles
Install the wheel and tire.
For additional information, refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

NOTE: If the dust cap is damaged a new dust cap must be installed.

Using a soft faced hammer and a wooden block, install the dust cap.


There is no real torque settings for the rear wheels, except to say, do not over tighten or you will stretch the lugs and the will loosen over time.

May 28, 2011 | Ford Fusion Cars & Trucks

1 Answer

Need to remove rear hub on rear wheel drive 04 ford transit with shoe brakes cause play in the hub


The brakes are adjusted out. There is a slot on the back side of the hub on the bottom in the six o'clock position. You can get a brake tool or use a screwdriver. It is two pieces threaded with a wheel in the center of it. You must turn it so it brings the shoes inward. Yo'll know which way it's turning after a little bit. It can be a challenge but take your time, get comfortable <-that's key and turn away. The drum should slide right off.

Jan 12, 2011 | Ford Transit Connect Cars & Trucks

1 Answer

Front nearside brake stays on when footbrake released


Replace the caliper on that side, or if you can, the piston in the caliper - that's what's sticking.

Until you get it fixed, the only workaround is to use the parking brake to stop the vehicle, instead of the main hydraulic braking system.

Oct 08, 2010 | 2010 Ford Transit Connect

2 Answers

How to replace rear wheel bearings


don't have topaz. maybe escort will help guide you.

Section 04-02: Suspension and Wheel Hubs, Rear 1996 Escort, Tracer Workshop Manual
REMOVAL AND INSTALLATION Wheel Bearing and Hub Assembly NOTE: Wheel bearings are not serviceable and should therefore be replaced as an assembly with the wheel hub (1104).

Removal
  1. Raise and support the vehicle.
  1. Remove the wheel and tire assembly.
  1. Remove the hub grease cap (1131) from the wheel hub.
  1. If equipped with disc brakes, remove the rear disc brake caliper (2552) and rear disc brake rotor (2C026). Refer to Section 06-04 for the removal procedure.
  1. If equipped with drum brakes, remove the two brake drum screws and the brake drum (1126).
  1. Unstake the rear axle wheel hub retainer (4B477) securing the wheel hub to the rear wheel spindle (4A013). Remove and discard the rear axle wheel hub retainer.
  2. Remove the wheel hub from the rear wheel spindle.

Feb 06, 2010 | 1990 Mercury Topaz

1 Answer

Brakes locking up


There can be a couple of things that can cause it. If the shoes are worn too bad, the piston can expand to its furthest travel and not be able to retract. If the master cylinder is bad, it may not be letting brake fluid to return to resevoir, likewise a wheel cylinder may be scored and leaking into the drum. Loose or broken parts rolling in the brake drum may be siezing against the drum when the brakes are applied. And lastly the brake may be adjusted to tight (these have a star adjuster that tightens the brake adjuster when rolling backwards and appying the brake.) Hope this helps, Marvin

Jan 21, 2010 | 1989 Ford F 150

1 Answer

How to install wheel bearing hub assemble (front)1998 on a ford escort


front or rear?

Assuming rear, on the brake drum:

Hub Removal
  1. If equipped, remove the brake drum (1126) ; refer to Section 206-02 . If equipped, remove the rear disc brake rotor (2C026) ; refer to Section 206-04 .
  1. Remove the wheel hub.
    1. Unstake the rear axle wheel hub retainer.
    1. Remove the rear axle wheel hub retainer and discard.
    1. Remove the wheel hub (1104).

Nov 05, 2009 | 1998 Ford Escort

2 Answers

How do you adjust the parking brake?


Adjusters are on the cable neer the left rear brake.If they are not siezed then it's a piece of cake,just unlock the jam nuts and tighten.If they are siezed then you need hear and patience.

Oct 23, 2009 | 1999 Ford Windstar

1 Answer

Hi I have a ford transit 04 2.4 chassis cab TDIC HOW TO FIT DICS


hi you need a very large socket i think its 65 12 corner, and yes u have to take disc of hub etc.

Apr 12, 2009 | 2004 Ford F350

1 Answer

Rear brake drum 1996 Ford winstar 3.8L


relase your hand brake also loose the brake adjustment to get gap between the darum and shoes.

Oct 19, 2008 | 1996 Ford Windstar

Not finding what you are looking for?
2002 Ford E350 Logo

2,019 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...