Question about 1993 Jeep Cherokee Country

1 Answer

How do i remove stop relay switch at brake pedal grand cherokee 2000 model drawning if poss

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Disconnect the wire from the brake light switch, remove the 2 booster push rod nuts, slide out the push rod bolt.

Posted on Jun 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does the 2000 jeep grand cherokee have a lamp outage module


If you have no brake lights, and you've checked the fuses and the bulbs then, the problem is likely a the brake light switch on the brake pedal arm. The switch needs to be adjusted or replaced.
Hope this helps.

Feb 23, 2015 | 2000 Jeep Grand Cherokee

3 Answers

I just installed a replacement brake booster on my 2000 Grand Cherokee,and I have no brakes. There were no leaks and I didnt remove the brake lines upon removal of the old booster. Any suggestions?


Do you mean the brake pedal goes down to the floor quite easily and you literally have no brakes?
Do you mean the brakes are there but there is no power assistance?

If, as you say the hydraulic lines haven't been disturbed and no fluid lost, I doubt the problem is hydraulic and if the pedal feel was merely spongy that is probably what you would have said rather than you have no brakes.

Are you sure your new brake servo unit was identical in every respect to the one you removed including the internal push-rod and any seals and gaskets?
If there was something that needed transferring from the original to the new unit before fitting did you remember to transfer it?

If you are confident you got everything right there should be no reason to remove the unit and start again.

Even if the unit is faulty and providing no assistance the brake pedal should feel normal as with the engine switched off.

If this is the case you need to check that the front chamber is being evacuated of air and there are no leaks. If the usual checks prove negative then you could have a faulty unit.

If you need more advice please provide a more thorough description when you return.

Feb 05, 2015 | 2000 Jeep Grand Cherokee

2 Answers

Hi, i have a 1997 jeep grand cherokee, and the brake lights will not go off. i have never seen this before, any suggestions?


Brake light switch is staying in the on position. It's located under the brake pedal. It will have to be replaced and can easily be done at home.

Feb 19, 2011 | 1997 Jeep Grand Cherokee

1 Answer

My tail lights will not turn off 2000 Jeep Cherokee


brake pedal switch top of brake pedal stuck tap with screwdriver if that dont work replace brake light switch hope this helps

May 08, 2010 | 2000 Jeep Grand Cherokee

1 Answer

The brake lights on my 2000 Jeep Grand Cherokee won't shut off.


The brake light switch is defective or out of adjustment. More than likely located on the brake pedal arm near the top.

Mar 11, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Replacing brake stop switch


Look at the top of the brake pedal you will see the switch. Simply unplug the connector and remove the nut (if applicable).

Jan 06, 2010 | 2001 Jeep Grand Cherokee

1 Answer

I already change the brake switch but the stop lights still on is there something else i could check to solve this problem


there is a plastic cap at your brake pedal which suppose to press to the switch when you release the pedal, it might be worn out.

Jun 21, 2009 | 2000 Jeep Grand Cherokee

2 Answers

1997 Jeep grand cherokee


Sounds like your brake light switch needs to be replaced.  It is attached to the brake pedal and should cost you around $20 from an auto parts store.  If the fuses and bulbs are good there is a 99% chance it is the brake light switch.  Hope this helps!  Thanks for an honest rating and for using FixYa.

May 19, 2009 | 2000 Jeep Grand Cherokee

1 Answer

No brake lights on 2000 jeep grand cherokee limited


if you have a park light working change your stop light switch it is broken.

Apr 15, 2009 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
1993 Jeep Cherokee Country Logo

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...