Question about 1994 Nissan Laurel

Open Question

How to remove the console fixture of a c34 laurel

C34 medalist

Posted by Anonymous on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Taking wiring out of chandalier tonight please help

Canopy is held on with a lock ring remove that
Fixtures still up with screws from fixture bar disconnect wiring make sure switch is off
Remove 1 screw at a time fixture will come after 2nd screws removed goid luck!!

Nov 29, 2017 | Cars & Trucks

1 Answer

Tools needed to change the left front pressed wheel bearing on 2008 jeep patriot

so working FSM free,,so you ask us to read our for you.?
sure. (last page (fsm) on front bearing page covers tools.)
"special tools not normal mech tools? {"
so are you 100% tool free shop , we cant guess your shop, not ever.

Book on MK 08 (jacks, wrenches, sp. jeep tools, torque wrench)
quote, partial, just removal. parts
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Raise and safely support the vehicle. (jacks and stands)
  3. Remove the front wheel. (lug wrench)
  4. Remove the steering knuckle assembly from the vehicle. Refer to Steering Knuckle, removal & installation.
  5. Position the locator block for Special Tool 9712 Fixture, as follows:
    • For left side knuckles, place the locator block to the left side on the Fixture. The side of the locator block with the angle cut goes downward, toward the Fixture. Install the mounting screws and tighten them to approximately 40 ft. lbs. (54 Nm).
    • For right side knuckles, place the locator block to the right side on the Fixture. The side of the locator block with the angle cut goes downward, toward the Fixture. Install the mounting screws and tighten them to approximately 40 ft. lbs. (54 Nm).
    • Install the knuckle in the Fixture as shown, guiding the steering arm to rest on the locator block and the brake caliper mounting bosses on the two Fixture pins.
    • Place the Fixture with knuckle installed into an arbor press.
    • Position Special Tool 9712-2 Remover/Installer in the small end of the hub. Lower the arbor press ram and remove the hub from the wheel bearing and knuckle. The bearing race will normally come out of the wheel bearing with the hub as it is pressed out of the bearing.
    • Remove the knuckle from the Fixture and turn it over.
    • Remove the snap ring from the knuckle using an appropriate pair of snap ring pliers.
    • Place the knuckle back in the Fixture in the arbor press ram.
    • Place Special Tool MD-998334 Installer on the outer race of the wheel bearing. Lower the arbor press ram and remove the wheel bearing from the knuckle.
    • end , i stop here,
log in to and read.
or buy the FSM

if lucky use youtube to find persons doing this , tool free.
Jerryrigging happens

Mar 10, 2015 | 2008 Jeep Patriot

1 Answer

Nissan laurel manual pdf

My US database won't have info on this vehicle. If your fuel injected, there is no choke, gasoline vehicle. I just don't have any info on this vehicle, sorry.

Nov 21, 2014 | 1994 Nissan Laurel

1 Answer

Remove center console

There are special radio removal tools, find out which one fits your radio.

Nov 27, 2013 | Cars & Trucks

1 Answer

Free Nissan Laurel C34 repair manual

hello i have an nissan c34 rb20e,what kind of auto trainsmission fluids are recommended to use.

Jan 24, 2012 | Cars & Trucks

1 Answer

How to repair center console lights Shifter lights burned out how do i remove to replace bulbs

driver side of the shift console slide the driver seat back you will see an oval cover pry it out with a small screw driver look inside you will see a black electrical fitting with two blue wires use a long needle nose pliers to gently turn and lower the light fixture(black electrical fitting with two blue wires) pull out of the oval opening change the bulb and reverse the operation no console removal needed..

Oct 28, 2011 | 2008 Chevrolet Aveo

1 Answer

How to changed the gear shifter light of a 2001 lexus gs 300?

If this car has a floor mount shifter, you will have to remove the center console. just look closely for all the hidden screws . If you study it for a minute, you will see how to remove it. After you lift off the console the light fixture will be right there, install new bulb. It doesn't hurt to check to make sure it works before you reassemble the console. hope ths helps.

Jan 25, 2009 | Lexus GS 300 Cars & Trucks

1 Answer

How do I replace a Tail Light on a 2002 Honda CRV

Pretty simple just remove the light fixture then you just have to remove the bulbs from the fixture and wire assembly remains intact then just fit the same bulbs in to the new light fixture without removing the wire assembly.

Dec 27, 2008 | 2002 Honda CR-V

Not finding what you are looking for?
1994 Nissan Laurel Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

80637 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides