Question about 1994 GMC Sierra

1 Answer

Leaking brake line(drivers side)

My brake line on the left side of my truck, bleeds out all of my fluid from the reservoir. I was just wondering how much would it cost to get that part replaced?

thank you

Posted by on

  • buell_rider8 Jun 20, 2009

    It is a 4wd pickup. My fault, I forgot to mention that. I appreciate the quick response, hopefully it will be fixed for cheap!



    Thank you

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 37 Answers

The hose is only maybe 15- 20 bucks depending on if its a 2wd or 4wd. I don't know what a brake shop will charge. They will just have to bleed all brakes and replace 1 line. a 4 wheel brake bleed is usually around 40 - 50 bucks, plus the labor to change the hose. This happens when stupid retarded brake guys change the pads and let your calipers hang by the hose. Thats the most common reason. However if one side is cracking bad and leaking, then it would be best to replace both sides and check the rear distribution block hose.

Posted on Jun 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Brakes went out,master cylinder is dry. filled the master cylinder pumped brakes and bled rear drivers side


    If there is a substantial fluid eruption, there are air bubbles still trapped in the system. You must repeat the bleeding procedure to remove that air. A modest disturbance in the fluid returning to the reservoir indicates a properly bled brakesystem.

    How To: Bleed Your Brakes - Feature - Car and Driver

    www.caranddriver.com/.../how-to-bleed-your-brakes-feature Car and Driver
Feedback

How To: Bleed Your Brakes - Feature - Car and Driver

www.caranddriver.com > Features

Car and DriverIf there is a substantial fluid eruption, there are air bubbles still trapped in the system. You must repeat the bleeding procedure to remove that air. A modest disturbance in the fluid returning to the reservoir indicates a properly bled brake system.

How to Bleed Brakes - Tips on Bleeding Brakes

Jan 01, 2016 | Cars & Trucks

1 Answer

Leaking fluid around left front wheel of 2001 Audi A6


If it is near the tire it is brake fluid. The brake fluid reservoir is back by the firewall driver side of engine compartment. Your car uses DOT 4 brake fluid.

Feb 13, 2014 | Audi A6 Cars & Trucks

2 Answers

1994 Toyota Camry clutch goes to the floor and stays there what would be the problem for that, and is there an easy fix


Sounds like the clutch slave might be the issue. You should be able to find it on the front of the transmission. Peal back the rubber boot and see if brake fluid drips out. If there is fluid behind the boot than it is leaking. You can also look up under the dash to see it the clutch master is leaking. It will leave a brake fluid trail from where the metal rod goes in. If either of those are leaking than your clutch fluid reservoir is likely empty. You can find it under the hood just to the drivers side of the brake fluid reservoir. After you have replaced the leaking parts fill the reservoir with new brake fluid and bleed the system. Make sure you keep the reservoir full while you are bleeding. You should be back in business when you are done!

Aug 07, 2012 | 1994 Toyota Camry

1 Answer

1994 buick century brakes went out fluid leaking from rear


Brake lines by rear door on drivers side are a common failure point. lines under door failing can cause a total brake failure. Just replace and bleed the lines.

May 31, 2012 | 1994 Buick Century

2 Answers

The brake cylinder in the right rear tire started leaking. I changed it and bled the brakes., now they won't stop and will go all the way to the floor. where and how do I adjust them? THANK YOU jOE!


You may need to further bleed the brakes. Something pumping to bleed the brakes can **** in air at the brake fluid reservoir. Try using a vacuum pump to **** out brake fluid from the release screw at the brake side. Make sure you always have enough fluid at the reservoir.

Feb 28, 2011 | Chevrolet Caprice Cars & Trucks

2 Answers

My brakes will not get hard. The pedal goes to the floor. I just changed rear caliper and rotor on the drivers side.


DId you bleed the system after you changed the caliper? If the Master cylinder lost it's fluid while you were changing the caliper, then there is air in the system and you need to bleed the entire system. start with the REAR RIGHT, then the REAR LEFT and then the FRONT RIGHT and last the FRONT LEFT. make sure the master cylinder NEVER runs low on fluid and DO NOT re-use any fluid that you get out of the calipers.

Dec 27, 2010 | 1992 Cadillac Seville

2 Answers

Brake pedal goes down to the floor to make it stop


check first the brake fluid reservoir to see if it is full, then bleed the brakes if the petal will not come up.

Dec 25, 2010 | 2000 Ford Taurus

3 Answers

Mazda e2200 clutch repair: feels like I still have some kind of pedal springback, but without much force. No clutch at all. I assume it is hydraulic, but the only reservoir I see is for the brakes. That is...


Yes, hydraulic--check again--fender side of brake master. Slave is usual cause of leak that eventually causes master reservoir to go dry and start drawing air. Check slave for leak. If leaking, replace slave and bleed system. Make sure to bench-bleed slave before installation by opening bleeder and pouring fluid into line port.

jturcotte_373.gif
  1. Raise and support the front end on jackstands.
  2. Back off the flare nut on the fluid pipe to free the slave cylinder hose.
  3. Pull off the hose-to-bracket retaining clip and pull the hose from the bracket. Cap the pipe to prevent fluid loss.
  4. Unbolt and remove the slave cylinder.
  5. Installation is the reverse of removal. Tighten the bolt to 12-17 ft. lbs. (16-23 Nm).

Dec 04, 2010 | 1988 Mazda B2200

1 Answer

Leaking brake fluid hose/system


Replace the leaking line, then bleed the system of all the air in the lines. Start at the furthest point from the reservoir. Until there is no air bubbles in the system.

Jun 12, 2010 | 1994 Chevrolet Cavalier

1 Answer

Bleed the brake lines


start at the passenger rear tire, have someone PUMP up brakes and hold pressure on them, release pressure by locating small bleeder screw, loosen screw 1/4 turn, brake fluid/air should come out, after brake petal reaches floor tighten bleeder, repeat process until only brake fluid comes out. go to driver side rear repeat, go to pass. side front repeat, go to driver side front repeat, after each bleeding make sure you check brake fluid in reservoir.

Sep 24, 2009 | 1984 Ford Mustang

Not finding what you are looking for?
1994 GMC Sierra Logo

267 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...