Question about 2004 Ford F150

Open Question

2004 Ford F150 broken wheel bolts - 2004 Ford F150

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

rtpflh
  • 546 Answers

SOURCE: Changing the starter on a 2004 Ford F150 with a

you'll need to use a socket.ratchet & extension.label the wires.

Posted on Sep 26, 2009

sscullys
  • 984 Answers

SOURCE: 2004 ford f150 supercrew will not engage in 4

Could be a problem with the vac lines to the IWE ( Integrated Wheel Ends ), or a problem with the IWE solenoid, or a problem with the vent from the IWE.

Start with checking the vac lines, to make sure they are not cracked.
The vac res & IWE solenoid are behind the battery. Here is a diagram of the parts in the IWE vac system
80605f9.jpg

There was a TSB for the 2004-2006 MYs with a bad design IWE solenoid, but this usually was coupled with noise in 2WD.
Start with checking the VAC lines and the vent, next would be to check the IWE solenoid.

Here is the PDF of the TSB on IWE solenoid
http://my.voyager.net/~sscully/file_tsb06_08_15.pdf

Posted on Nov 28, 2009

sscullys
  • 984 Answers

SOURCE: 2004 Ford F150 supercrew will not go into 4 wheel

Already replied to your other post on the same topic :
http://www.fixya.com/cars/t3532879-2004_ford_f150_supercrew_will_not_engage

Could be a problem with the vac lines to the IWE ( Integrated WheelEnds ), or a problem with the IWE solenoid, or a problem with the ventfrom the IWE.

Start with checking the vac lines, to make sure they are not cracked.
The vac res & IWE solenoid are behind the battery. Here is a diagram of the parts in the IWE vac system
e84e68b.jpg
There was a TSB for the 2004-2006 MYs with a bad design IWE solenoid, but this usually was coupled with noise in 2WD.
Start with checking the VAC lines and the vent, next would be to check the IWE solenoid.

Posted on Nov 28, 2009

sscullys
  • 984 Answers

SOURCE: 2004 ford f150 4 wheel high will not engage 4 low

Operationally vacuum holds the IWE ( Integrated Wheel Ends ) out, and once vac is removed the spring engages the IWE.

Lift and support the front of the truck so the front wheels are off the ground ( take safety precautions, chock wheels, jack stands, etc )
Key on, engage 4x4 and try to turn the front drive shaft.
If it turns it is a problem with the transfer case.
If it doesn't it is a front axle engagement problem.

- If the front drive shaft does not turn :
Shut of the truck ( still jacked up, and supported ) remove the vac lines from the IWE. The spring should push the gears in, without the vac line on.
Check the vent line ( tube that is routed into the engine compartment with nothing attached to it ), for blockages.
If the vent line is clear, and with the vac lines off the IWE should be engaged ( both front wheels locked ).
If they lock, the problem is with the IWE solenoid not shutting off vacuum to the IWEs. There is a TSB on the 2004-2006 IWE solenoids, a newer revision has been made, and used from 2007 and newer MYs.

Here is a block diagram of the IWE system
sscullys_34.jpg

Posted on Dec 06, 2010

michaelhi580
  • 62 Answers

SOURCE: 2004 ford f150 4 wheel drive doesnt work

If your truck has Vacume actuated hubs check the vacume lines running to the hubs right behind the brake rotor. If it has the electronic actuated hubs, check connectors / and or replace actuator motor on the front diff. Also possible Transfer case motor seized if you have push button 4x4

Posted on Mar 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2wd.how to replace front wheel bearing assembly


There are a number of videos...
For RWD front hubs. (F250 will just have larger bolts.)

How To Install Replace Front Wheel Bearing Hub Assembly 2004-08 Ford F150
For 4x4 front hubs.

Ford Super Duty hub bearing replacement Driver side

May 06, 2016 | 2005 Ford F 250 Super Duty

1 Answer

2004 F-150 4X4 XLT EXT CAB 5.4L NEED FRONT WHEEL HUB ASSEMBLY DIAGRAM


  1. n0051415.gif
  1. Item
Part Number Description 1 W706540-S900 Axle-to-wheel hub nut (4x4 only)
Removal Note 2 - Wheel speed sensor harness connector
Removal Note 3 2027 Anchor plate bolt (2 required) 4 - Brake caliper, pads and anchor plate
Removal Note 5 1125 Brake disc 6 1107 Wheel hub-to-wheel knuckle bolts 7 1104 Wheel bearing and hub assembly
Removal Note 8 N642567-S36 Tie-rod end-to-wheel knuckle nut 9 W707254-S427 Lower ball joint-to-wheel knuckle nut 10 W520215-S427 Upper ball joint-to-wheel knuckle nut 11 3K185 Wheel knuckle
Installation Note 12 W710279 Integrated wheel and bolt (3 required)


Mar 07, 2011 | 2004 Ford F150

1 Answer

What combinations of sockets are used to remove 3 bolt on a starter on a ford f150 pickup


I just replaced the starter on my 2001 F 150 and had to use a 13 mm socket with a swivel and 3 long extensions. I reached the top and side bolts by going through the wheel well. You have to stick your head in over the tire to see the top bolt, but it was pretty easy to reach it with this combination. The side bolt I could either reach it from under the truck or through the wheel well, through the wheel well seemed easier using the swivel and extensions

Sep 04, 2010 | 2004 Ford F150

1 Answer

2004 F150 4X4 caps over both front axles and bolted to the inside of the spindles, has what appears to be a double vacuum hose going into it. They are either broken or corroded from their flange bolts onto...


Sounds like the IWE ( Integrated Wheel End ).

One of the lines is the vent line, routed into the engine compartment and is not connected to anything, the other runs to the IWE solenoid.

This is a block diagram of the IWE vacuum system
512b77f.jpg

From your problem, I am not sure if the line is broken or the vacuum & vent mount on the IWE itself.

Jul 01, 2010 | 2004 Ford F150

1 Answer

Broken lug nuts


Get how ever many wheel bolt's you need and one more lug nut, you will used that one to press in new wheel bolt, any parts place will have these parts, remove tire with hammer hit broken stud till it come's out through the back side, put new wheel bolt and with extra lug nut press in bolt, hope this was very helpful.

May 20, 2010 | 2004 Ford F150

1 Answer

Broken tilt steering lever


BROKEN PART BEST FIX BY REPLACING BUT IF YOU HAVE THE BROKEN PIECE YOU CAN ALWYS TRY J B WELD SHOLU BE ABLE TO GET AT YOUR LOCAL AUTO PARTS STORE WILL HAVE TO DO SOME SANDIND DOWN FOR LOOKS

Apr 12, 2010 | 2004 Ford F150

1 Answer

Ford f150 will not go into 4 wheel when it is cold


in the vacuum line or shift motor. blow out lines and remove vacuum motor and drain.

Jan 29, 2010 | 2004 Ford F150

1 Answer

2004 Ford F150 right rear taillight Change


OPEN THE TAILGATE AND YOU WILL SEE TOO BOLTS OR SCREWS..UNDO THEM AND PULL ON THE ASSEMBLY AND IT WILL COME OUT....PRETTY SIMPLE THEY ARE PRESSED IN...

Jul 08, 2009 | 2004 Ford F150

1 Answer

I have a 05 F150 FX4 4x4...Problem is the 4x will not engage..I think I've checked all the fuses, not sure. could it be anything or anyplace else?


check the switch under the hood. right hand side on the fire wall just under the wiper cowl. this happened to me. ford says water from the wipers leak on the switch and shorts it out. they replaced the switch and losely put a plastic over it to keep the water out. make sure not to put the plastic too tight, it is vacuum , so it needs to breath. Also check the front wheel accuators that engage the front end(next to the wheels), ford had some bad accuators that would not hold the pressure this to also happened to me. ford should pass it on a goodwill warranty. hopefully nothing else is broken. cost me $500 because i damaged the wheel bearings. ford won't pay for those.

Jan 26, 2009 | 2004 Ford F150

Not finding what you are looking for?
2004 Ford F150 Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...