Question about Hyundai Cars & Trucks

Open Question

How to remove glove box housing on Elantra 2008 ?

I removed the glove box, removed all screw and even air vent screw on the right side. The air vent doesn't move, it doesn't come out and the glove box housing still there, it can't move. I removed almost every thing and still the upper plastic can't be remove it. am'I missing some thing? I've looking every where and can find an explanation or video go to the point. I want to get access to every thing on the back of glove compartment . Thank you

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: How do I remove the glove box? I have removed 2

After removing the three screws, the glove box is held with two clips - one on each side. The clips will come undone when you pull on the glove box with a little force. You will then need to unplug the switch/lamp connector.

Posted on Nov 27, 2009

Ad
mcdevito75
  • 1970 Answers

SOURCE: How do you remove the glove box lock form a 1962 corvette?

mcdevito75 here, Remove the lock from the glove box. If the glove box is closed and lockes, you"ll have to somehow get the lock tumbler out of the lock. If the glove box is open simply remove the screws or clip holding the lock in place.

Posted on Jul 11, 2010

michael4wgv
  • 166 Answers

SOURCE: Need to remove the glove compartment to change the

if you removed all 6 screws. there are 2 on bottom. 2 on top and 2 in front on the side. pop out the light and release the electrical connector. then grab a hold of the glove box door from each side and pull hard. it will feel like your going to break it but it won't. you really have to pull on it kinda hard. right when your ready to stop cuz you think it will break just pull a little harder. you will be shocked when you see how much force is needed to get the glove box out.

Posted on Sep 28, 2010

  • 1 Answer

SOURCE: How do you remove the

http://www.wikihow.com/Change-the-Cabin-Air-Filter-in-a-Toyota

Posted on Jan 23, 2011

  • 2187 Answers

SOURCE: I'm trying to replace the

If you were able to remove the brace for the box (found when you open the glove box) with a screwdriver, feel the sides and its top for stops you need to remove them. The cabin filter should be at the back where you had the glove box. You should be able to pull out the housing out and remove the dirty filter.

Posted on Apr 30, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Update to the problem with the ac motor making noise; i found that a small plastic bag i had in the glove box has been sucked up into the fan motor how do i get it out


Removal & Installation
  1. Disconnect and isolate the negative battery cable.
  2. If equipped, remove the instrument panel silencer from the passenger side of the instrument panel.
  3. Remove the glove box from the instrument panel.
  4. Disconnect the blower motor wire harness connector (1) from the blower motor power module or resistor (2), depending on how equipped.
    36543_cher_g0409.gif

    Disconnect the blower motor wire harness connector (1) from the blower motor power module or resistor (2)

  5. Remove the three screws (3) that secure the blower motor (4) to the HVAC housing (5).
  6. Remove the blower motor from the HVAC housing.

To install:

  1. Position the blower motor into the HVAC housing.
  2. Install the three screws that secure the blower motor to the HVAC housing.
  3. Connect the wire harness connector to the blower motor power module or resistor, depending on how equipped.
  4. Install the glove box into the instrument panel.
  5. If equipped, install the instrument panel silencer onto the passenger side of the instrument panel.
  6. Reconnect the negative battery cable.

Jul 10, 2012 | 2008 Jeep Grand Cherokee

1 Answer

Replace cabin filter f150 lariat 2006


This is one of those topics that I have seen both ways.

1. The 2004 was the only MY to include an airfilter.
2. The late build 2004 to 2008 could have a dealer installed cabin air filter kit installed.

So don't be shocked if you go fishing for it, and it is not there. On to the directions :

Open the passenger-side glove compartment box. Remove all of the items currently stored in the glove box

Notice two screws on the inside ceiling of the glove box securing the glove box to the dashboard. Use a flat-head screwdriver to remove these screws. The glove box will now be loose. Wiggle the box off the dashboard and allow it to hang.


Locate the rectangular plastic housing; this is where the cabin air filter is stored. Remove the housing cover by pulling it out of place. Remove the dirty cabin air filter by sliding it out of the clips securing it in place. Discard the dirty filter.


Slide the replacement cabin air filter into the retainer clips. Push the filter housing cover back into place until you hear it lock. Place the glove compartment back into place. Replace the two screws that secure the glove box in place and tighten with the screwdriver. Place the items back into the glove box and close the box.

Apr 10, 2011 | 2006 Ford F-150

1 Answer

Change cabin air filter 2080 Subaru outback


Your cabin filter is hiding above/behind your glove box. In order to access the cabin filter, first remove the passenger instrument panel side cover. Next, open your glove box and there should be one clip on the left and right side of the glove box... remove those clips as well as the tether that is holding the glove box up. After the glove box falls forward, remove the upper storage box. You should now see the cabin filter access panel, which is held in with 5 or 6 screws. Remove the screws, pull the access panel out, and you should see the cabin filter. Reverse instructions for installation.
Please let me know if I may further assist you. -TXTEXAN

Nov 22, 2010 | 2008 Subaru Outback

1 Answer

Hjow do i rermove the radio from my 325 i 2003



Removal & Installation-of dashboard which includes removing radio.


CAUTION Many BMW models covered by this manual are equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, properly disable the SRS.
The instrument panel removal is complex and requires disconnecting many components. Make sure to label and organize the components as they are disconnected, disassembled or removed.
3 Series Models

  1. Disconnect the negative battery cable. If equipped with a Supplemental Restraint System (SRS), wait for a period of 11 minutes before proceeding.
  2. If equipped, disable and remove the SRS components as necessary.
  3. Remove center console as outlined in this section.
  4. Remove the glove box compartment as follows:
    1. Open the glove box door and remove glove compartment mounting screws.
    2. Pull glove box compartment outward, and disconnect the electrical connectors as necessary.

  5. Remove lower left dash trim piece as follows:
    1. Remove the lower dash panel mounting screws.
    2. Pull the lower dash panel to the left and back and disengage it from the driver's side footwell retaining clips.

  6. If equipped, remove the driver's side and passenger airbags.


CAUTION Make sure to store the airbags properly in a safe area.
  1. Remove steering wheel.
  2. Remove driver side knee bolster fasteners and remove.
  3. Remove the following components:

    Instrument cluster Headlight switch Radio Climate control head and module.
  4. Remove the turn signal and windshield wiper/washer stalk switches as outlined in Section 8.
  5. Remove windshield (A-pillar) trim from both left and right sides.
  6. Remove the reinforcement bar below the steering column, then remove steering column shear bolts. Carefully lower steering lightly and support the column to avoid damaging the spindles.


WARNING Lowering the steering column too far can damage the spindles.
  1. Remove the glove compartment support frame fasteners, then remove the frame assembly.
  2. Carefully release and lift out the defroster outlets (both left and right sides) at base of windshield. Remove the screws located below the outlets.
  3. Remove the mounting bolts on the left and right sides of the dash board assembly.
  4. Carefully lift the instrument trim panel off slowly. Make sure all harness connectors and wiring are disconnected.
  5. Installation is the reverse of the removal procedure.

Z3 Models
  1. Disconnect the negative battery cable. Wait for a period of 11 minutes before proceeding.
  2. Disable and remove the (SRS) components as necessary.
  3. Remove center console as outlined in this section.


CAUTION Make sure to store the airbags properly in a safe area.
  1. Remove steering wheel.
  2. Remove driver side knee bolster fasteners and remove.
  3. Remove the following components:

    Instrument cluster Headlight switch Radio Climate control head and module.
  4. Remove the turn signal and windshield wiper/washer stalk switches as outlined in Section 8.
  5. Open the glove box, remove the four finishing caps near the glove box door lock catch and remove the screws.
  6. Remove the trim caps and screws from the far right end of dash and next to the center air vents on right side of the center console.
  7. Close the glove box, then pull it downward and out slightly.
  8. Remove the two screws securing the glove box cover and remove the cover.
  9. Remove the two fasteners securing the passenger side air bag bracket-to-support brace.
  10. Remove the two mounting fasteners on each end of instrument panel, in the door jamb areas.
  11. Remove the two mounting fasteners located under center air vents.
  12. Remove screw trim caps at the base of windshield and remove the screws.
  13. Carefully lift the instrument panel up and remove it from the passenger (right) side of the vehicle.
  14. Installation is the reverse of the removal procedure.

Nov 12, 2010 | 2003 BMW 325

1 Answer

How to change cabin air filter in toyota avalon 2002?


1) Turn off the ignition switch while leaving the wipers in the up position. 2) Open the hood and properly secure it in the open position. 3) Gently pull the rubber cowl seal away from the cowl vent screen. Place your hand underneath the right half of the cowl vent screen and lift straight up, thereby releasing the four spring clips and removing the right half of the screen 4) Remove the water shield. Carefully disengage the two water shield locking tabs and slide the water shield toward the front of the vehicle, lifting the water shield up and away from the vehicle 5) Remove the Passenger Compartment Air Filter, being careful not to allow debris or loose components to fall into the filter housing. Replace the Passenger Compartment Air Filter with a fresh filter and reverse the above procedures to reassemble the vehicle components. �
I am not sure what time in the year your 2001 Avalon was built but her is the procedure that I just followed: 1. Open glove box and remove contents 2. Remove the three philips head screws along the top inside frame of the glove box. 3. Remove the hex head bolt in the lower right and Philips screw in the lower left side of the glove box frame. 4. Unlatch the black cover plate from the roof of the glove box. This holds an electrical connection and will need pushed up through the hole when the entire box is removed. 5. Pull on the top left side of the glove box to release the pop tab. Repeat on the right side. 6. Carefully lower the glove box assembly. 7. Disconnect the electrical connection to the trunk disable button 8. The entire glove box can now be removed from the area. The door gear assembly does not come off of the box and is easily damaged if attempted to do so. 9. The Cabin Air Filter assembly has a white cover. Pop the tabs on the right and left side and slide the assembly out. 10. Replace the filter in the assembly. Make sure the airflow indicator points down. 11. Re-Install Air Filter assembly. 12. Re-Install the electrical connections remembering to slide the one through the hole in the top of the glove box. 13. Push glove box assembly on pop tabs. 14. Re-Install screws and bolts. 15. Reconnect the black cover plate to the top of the glove box.
rate it

Jan 08, 2010 | 2002 Toyota Avalon

2 Answers

How to remove dash for heater core removal


1981-87 Models

  1. Disconnect battery ground cable.
  2. Discharge A/C system and disconnect refrigerant and heater lines from unit.
  3. Move shift levers away from dash.
  4. Remove right side cowl trim panel, if equipped.
  5. Remove 4 screws at base and remove glove box.
  6. Remove brace through glove box opening and remove ashtray.
  7. Remove right half of lower reinforcement (7 screws to instrument panel and 1 to cowl side of trim panel).
  8. Disconnect radio ground strap.
  9. Remove right upper air duct by removing mounting screw and pulling duct out through glove box opening.
  10. Remove instrument panel center brace and right instrument panel cluster pivot bolt.
  11. Remove instrument panel cluster, disconnect shift indicator cable and lower steering column.
  12. Remove steering column studs and radio.
  13. Remove scoop connecting heater to center distribution duct (2 screws).
  14. Remove center distribution duct by pulling bottom of dash out to gain clearance.
  15. Remove floor air distribution duct.
  16. Disconnect temperature control cable through glove box.
  17. Remove 7 retaining nuts from firewall and screw that retains assembly to cowl side sheet metal.
  18. Flex dash out and remove heater assembly.
  19. Remove nuts from door arms and remove door arms.
  20. Remove 7 screws to remove cover from housing.
  21. Remove evaporator core.
  22. Reverse procedure to install.

Oct 17, 2009 | 1985 Dodge Ramcharger

1 Answer

Where is the cabin air filter located at and how do i get to it.


It will either be behind your glove box, or will be located under your hood by the firewall.

    Behind the Glove Compartment
  1. Open the glove compartment and remove all the items from inside of it.
  2. Remove the glove compartment assembly retainer screws with a Phillips head screwdriver. Refer to the repair manual for your specific year and model series BMW for the exact location of the screws or carefully look around the perimeter of the interior glove box assembly to locate the screws.
  3. Locate the lower trim panel retaining screws behind the glove box assembly. Remove the screws with a Phillips head screwdriver and then remove the panel.
  4. Remove the foot-well air duct.
  5. Loosen the retaining screws of the control module box to all you to lower it down.
  6. Turn the cabin air filter panel retaining knob counterclockwise to open the panel. Pull the filter removal tab outward to remove the filter.
  7. Use a shop vac to clean out any noticeable debris from the cabin air filter housing interior.
  8. Insert the new filter and reverse the order to reassemble the foot-well air duct, the trim panel and the glove compartment assembly.
  9. Under the Hood
  10. Open the hood and locate the cabin air filter housing. The housing is located near the cowling on the top section of the firewall. Some models place the housing in the middle of the cowling, on both sides--left and right--of the cowling or on the passenger side cowling. Removal of the cowling and placing the windshield wipers in the upward position may also be required on certain models. Some 7-Series BMWs place the filter housings on both the left and right side undercarriage of the hood.
  11. Release the cabin air filter duct clamp. This can either be released by unclipping the air filter duct by pressing a retaining lock with your fingers or using a flathead screwdriver to pry off a retaining rod.
  12. Lift the cover upward--or downward on hood-installed 7-Series BMWs--to reveal the cabin air filter.
  13. Remove the cabin air filter from the air duct. Vacuum the air duct with a shop vac.
  14. Insert the new cabin air filter(s) and reassemble.

Oct 16, 2009 | 1993 BMW 7 Series

2 Answers

How to change front blower motor in a 2003 dodge caravan


Removal & Installation
CAUTION The Supplemental Inflatable Restraint (SIR) system must be disarmed before removing the blower motor assembly. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.

  1. Disconnect and isolate the negative battery cable, then wait 2 minutes before proceeding with the removal. This will effectively disable the air bag system preventing possible personal injury.
  2. Remove the glove box from the instrument panel
d6b70fa.gif
The blower motor is located behind the glovebox, behind the blower motor cover

  1. Remove the A/C-heater blower motor cover.
  2. Disconnect the blower motor wiring connector.
  3. Remove the blower motor wiring grommet and feed the wiring through the blower motor housing.
  4. Remove the blower motor mounting screws.
0e0729c.gif
Once the cover is removed, unplug the electrical connector and push it through the opening in the housing

1ed158c.gif
The blower motor is secured to the housing with three small screws

  1. Allow the blower motor assembly to drop downward to clear the instrument panel and remove from vehicle.
To install:
  1. Place the blower motor assembly into position on the A/C-heater unit and tighten the mounting screws.
  2. Route the blower motor wiring through the blower motor housing and seat the wiring grommet in the hole of the blower motor housing.
  3. Reconnect the blower motor electrical connector.
  4. Install the A/C-heater blower motor cover.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable. Check blower motor operation.

Oct 12, 2009 | 2003 Dodge Caravan

2 Answers

2008 honda pilot cabin air filter


This solution pertains to a 2008 Honda Pilot...To replace the cabin air filter which is located on the passenger side of the vehicle behind the glove box: Open glove box and remove stored items...while sitting in the passenger seat, pull towards you on each of the two clips on the left and right side of the glove box...this will cause them to become loose and the glove box will tip out completely exposing the inside of the dashboard. (Alternately...carefully pull towards you on the top center of the glove box which will cause the left and right side stops to pull away from the edges and allow the glove box to tip out) Here it gets tricky...the box holding the cartridge for the cabin air filter is the large black box on the left side behind the glove box The filter fits in a removable tray vertically inside that box. A pressure clip at the top of the box allows the vertical cover to be removed exposing the tray with the Cabin air filter... BUT!!! There is a plastic bar an inch or so high which has been placed there by the manufacturer to prevent most from changing the filter without the service department being involved. This bar must be cut with a sharp sheetrock knife or hacksaw and discarded, (it will not be reinstalled). Then there is a flat metal bar behind the plastic bar that can be removed using an 8mm socket and a phillips screwdriver. There are 2 8mm screws and one phillips head screw on each side that must be removed in order to remove the metal bar. THEN you can remove the cover to the cabin air filter box, pull out the tray with the filter (note how the filter is in the box so the new one can be placed the same way) reinsert the tray with the new filter and replace the tray cover. All other steps to finish the job are obvious as everything is the reverse. Actually the whole process is a lot of trouble and unless you are determined to change the filter I would recommend not doing it.

Aug 24, 2009 | 2008 Honda Pilot

2 Answers

How do i change a air filter on a 2003 e320 mercedes benz


There are swing clamps about six on both side of the air-box to the right front of the vechicle just lift up the cover and pull out the filter. The replacement will be a two depth fliter one side larger than the other that faces down into the bottom of the box and the shorter end goes twards the engine. If this is a cabin filter the glove box has to be removed ( easy ) just remove the six phillip screws and give the glove box door a good strong left to right pull and it shoud come out. just behind that is a retangle covering to the right with sliding lock. just slide the lock to the left and the cover comes off the filters come out left first and than right. reverse procedue other than the pulling of the glove box that should go back in easy.

Jul 05, 2009 | 2005 Mercedes-Benz Mercedes Benz E320 Cdi

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...