Question about 2007 Mazda CX-7

Open Question

What is a pcm in a mazda cx7 - 2007 Mazda CX-7

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Hrnsly
  • 154 Answers

SOURCE: Timing chain broke on a 2007 cx7 w 65K miles

you need to take it to your local dealer and raise a big fuss because this is a known problem and if you yell loud enough you should be able to get this fixed under warranty.

Posted on Aug 12, 2009

  • 1252 Answers

SOURCE: We were told we have

Are you sure they said EGR valve?..as far as i can see, there is no egr valve on this vehicle ???

Posted on Jun 07, 2011

Hobbit_who
  • 2044 Answers

SOURCE: Replacing struts on Mazda CX7

There are 3 Nuts inside the Engine Compartment, There is one Bolt on the Lower Arm and you have to remove the ABS and Torsion Rod. You need a Spring Compressor to do this job.

Posted on Apr 15, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace outer front door handle Mazda cx7 2010 model


Hey, I just use a metal zipstrip. Cheap and easy. Look on youtube for Prizm handle replacement. You basically slip it under the current handle and slip it in the zip buckle to make a loop. It's ghetto but works and does not use duct tape unlike most Red Green type "solutons".

Feb 01, 2015 | 2010 Mazda CX-7

1 Answer

Transmission problem with a 2007 Mazda cx7


This indicates a problem in the transmission control module as it is not activating the solenoids/servos and consequently the sensors that read turbine speed and output shaft speed are not reading the correct difference of the two units . Have this checked out at an accredited auto transmission shop.

Jun 16, 2014 | Mazda CX7 Cars & Trucks

1 Answer

2007 Mazda CX7 factory alarm started going off on it's own..just had it at the dealer to have PCM factory recall taken care of.I had to undo the negative side battery cable just to shut off the audible...


looks like they didnt fix the computer-nevr bring a car to a dealer-techs are inxperiencd---get a data stream run thats displays values so a good mech can decyfer--may need that computer reflashd w factory gear

Nov 10, 2013 | Cars & Trucks

2 Answers

I have a mazda cx7 2007. I dont think i am timing it correctly. can anyone give me some advice?


7_24_2013_12_05_24_am.gif7_24_2013_12_03_44_am.gif
Oh no,
Are you replacing VVT and chain? You need 2 special tools for this.. 1 to hold the camshaft where the slot is for the high pressure fuel pump, and another beside the crank damper on the rear of the motor, there is a small 10mm bolt that you remove and install a "holder" of sorts that holds the crank at TDC.
If you fail to do both of these steps before removing the chain you run the risk of throwing the timing out. Part numbers are as follows for the SST's.
Camshaft: (picture 1) SST 303-1061 (49 UN30 310610)
Crankshaft: (picture 2) SST 303-507

Jul 23, 2013 | Cars & Trucks

1 Answer

Replacing struts on Mazda CX7


There are 3 Nuts inside the Engine Compartment, There is one Bolt on the Lower Arm and you have to remove the ABS and Torsion Rod. You need a Spring Compressor to do this job.

Apr 15, 2013 | 2007 Mazda CX-7

2 Answers

How do I change the bulb in the low beam headlight in my 2007 Mazda CX7?


Removing the bulb in a CX7 is a real PITA. If replacing the right bulb, turn the steering wheel all the way to the right, or do the opposite for the left side. (or you can opt to remove the entire wheel on the corresponding side) You'll need to remove 3-4 of the fender well clips with a phillips screwdriver being careful not to break them. Once the screws are removed, pry back the wheel well cover to access the back of the headlamp to change the bulb.

Nov 04, 2009 | 2007 Mazda CX-7 Grand Touring

3 Answers

Timing chain broke on a 2007 cx7 w 65K miles


you need to take it to your local dealer and raise a big fuss because this is a known problem and if you yell loud enough you should be able to get this fixed under warranty.

Aug 03, 2009 | 2007 Mazda CX-7 Grand Touring

Not finding what you are looking for?
2007 Mazda CX-7 Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...