Question about 2004 GMC Envoy

Open Question

04 gmc envoy clock keeps resetting

Clock keeps resetting to 12:00

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Clock Settings for 2003 GMC Envoy

if it's the bose head unit, it's clearly displayed under one of the knobs on the left if i recall properly. hour and minute are seperate buttons.

Posted on Apr 13, 2009

  • 1311 Answers

SOURCE: 04 GMC Envoy 4.2 Get PO0171 code and since the

First thing to do is to run some Techron injector cleaner through the gas tank, then a cleaning of the throttle body is also very important. For more information, check out www.trailvoy.com, this forum is a wealth of information on Trailblazers and Envoys.

Posted on Sep 27, 2010

  • 1311 Answers

SOURCE: i want to replace front hub bearing on 04 gmc

35 mm

Posted on Oct 23, 2010

ryanlutton
  • 1121 Answers

SOURCE: license plate light out on

Has 2 screws for the cover, take them out and replace the bulb/s. Might check the seal that seals the entire license plate panel, it's black. Common problem is that this seal comes folded under from the factory and allows water into the bulb area.

Posted on Nov 30, 2010

  • 1 Answer

SOURCE: 04 GMC Envoy XUV midgate

The same thing happened to my '04 XUV. Discovered broken white nylon/plastic that retains the end of the lift cable. Ordered a new lift gate motor/mechanism assembly ($250) online and replaced it myself. Be sure to buy a new limit switch ($13) also. I did not and regretted it because you must remove the old limit switch from the old motor assembly so you can re-assemble it to the new motor assembly. While removing the old switch from the old assembly, I broke it. Had to then order a new switch. The cost to ship the switch separately was more than the switch. The whole thing did not really take that long and was surprisingly easy. It works great now.

Posted on Dec 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a filler neck for a 2001olds bravada. what other vehicles can it come off from


I'd stick with Blazer/Jimmy/Envoy Chevrolet S-10 & GMC Sonoma pick-ups (94-04). Inc. S-10 Blazer & GMC Jimmy (95-04), GMC Envoy (98-01) & Oldsmobile Bravada/Isuzu Hombre (96-01)

Aug 15, 2017 | Cars & Trucks

1 Answer

How do you replace rack & pinion in 2004 GMC Envoy and where are the jack stand support points?


Along with removing a fuel tank-- that is a
nasty, difficult job-- you may want to pay a
shop to do

Aug 14, 2014 | 2004 GMC Envoy

1 Answer

2005 gmc envoy gas cap stuck


take a pick or small screw driver and push it threw the cap in the middle of the space between the outer edge and the center then turn it off the is assuming your turning it counter clock wise

Aug 22, 2012 | 2005 GMC Envoy

1 Answer

04 gmc envoy randomly turns off when coming to a stop


You need to have the throttle body cleaned, make sure both the front and rear sides of the throttle body are thoroughly cleaned. Also, while the cleaning takes place, the battery should be disconnected to reset the computer and allow it to relearn to the cleaned throttle body.

Nov 04, 2011 | 2004 GMC Envoy

1 Answer

What does the code p0483 means for a gmc envoy?


DTC P0483 is set when the difference between the commanded cooling fan speed and actual cooling fan speed is greater than 1,000 RPM.
Reset the comp with the scanner, if it comes up again, then you may need to replace your fan clutch.
Technical Service Bulletin (TSB #04-06-04-090A) says, "The diagnostic calibration in the PCM may allow the DTC P0483 to set improperly." The bulletin directs technicians as follows: "Reprogram the Powertrain Control Module (PCM) with a new service calibration titled, 'New calibration to reduce the potential for setting P0483.'" this will have to be done at the dealership, or by a qualified mechanic.
Good luck.

Aug 19, 2011 | 2004 GMC Envoy

1 Answer

04 GMC Envoy 4.2 Get PO0171 code and since the envoy doesn't have a MAF sensor what is the most common problem.


First thing to do is to run some Techron injector cleaner through the gas tank, then a cleaning of the throttle body is also very important. For more information, check out www.trailvoy.com, this forum is a wealth of information on Trailblazers and Envoys.

Sep 14, 2010 | 2004 GMC Envoy

2 Answers

Clock Settings for 2003 GMC Envoy


if it's the bose head unit, it's clearly displayed under one of the knobs on the left if i recall properly. hour and minute are seperate buttons.

Mar 26, 2009 | 2003 GMC Envoy

1 Answer

2004 GMC Envoy SLT possible electrical problems


it sounds like you need a regulator for your alternater it is reversing polarity there for draining your battery and reseting the clock. it is located on the back of your alternator.hope this could help.

Jan 08, 2009 | 2004 GMC Envoy

1 Answer

Starting problems...


YES YOU NEED TO CLEAN YOUR TERMINALS

Aug 11, 2008 | 2002 GMC Envoy

Not finding what you are looking for?
2004 GMC Envoy Logo

Related Topics:

10 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...