Question about 2007 Jeep Liberty Sport

2 Answers

Rear wheel bearing

How to change rear wheel bearings

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 28 Answers

REMOVAL
1. Raise and support the vehicle. 2. Remove the tire and wheel assembly. 3. Remove the caliper adapter. CAUTION: Never allow the disc brake caliper to hang from the brake hose. Damage to the brake hose will result. Provide a suitable support to hang the caliper securely.
4. Remove the disc brake rotor. 5. Remove the wheel speed sensor. 6. Remove the bracket securing the wheel speed sensor wire. 7. Remove the axle shaft nut. (if equipped with four wheel drive) 8. Remove the three mounting bolts for the hub/bearing assembly. 9. Remove the hub/bearing.

Posted on Apr 23, 2014

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 26 Answers

Unless you have a hydraulic press, don't attempt this in your basic garage or driveway.

Posted on Apr 23, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6982 Answers

SOURCE: how do I change axel bearings on jeep GC ltd. 5.9?

Job is not terribly difficult, but instructions are too long to re-write them. Get yourself a haynes manual (about 20 bucks) and it will guide you through the job. If you need any help along the way, I'll be glad to help! (manual will help with lots of other stuff as well!!
If you have the setup I'm thinking of, make sure you buy a new diff cover gasket and gear lube along with axle bearing.
good luck

Posted on Mar 14, 2009

motor1258
  • 6674 Answers

SOURCE: Rear End Shake

Sorry didn't see heading for shake for some reason. One of the things I found on my nephews cherokee that caused same problem, was a build up on back of aluminum rims as well as on hub area where it mates when installed, that was never cleaned off when wheels were rotated or whatever. I scraped and wire brushed back of rims down to original metal again, as well as hubs, and problem was gone. If they don't mate even & flat against the two surfaces, then they aren't running true. I jacked it up & watched rim at outer edge when rotating, and could see it would wobble slightly.

Posted on Aug 09, 2009

michigan man
  • 3533 Answers

SOURCE: The front wheel bearings on my 2002 Grand Cherokee

give these websites a try its www.autozone.com and www.alldatadiy.com if all fails stop by your local jeep dealership in the parts department and they will print you out a diagram if that fails stop by your local library and get your hands on Haynes auto repair Manual for your SUV wish you the best of luck Michigan Man

Posted on Nov 04, 2009

ftw1952
  • 10319 Answers

SOURCE: noise at rear wheel

lift the rear axle off the ground and spin the wheels around as fast as you can. if the bearings are bad you will hear it if the sound changes as it spins. If it a scratching noise that will be from the disc brake pads

Posted on Jan 24, 2010

  • 2 Answers

SOURCE: replace the rear wheel bearing

better check a manual, The ones I have done do not have c-clips in the diff. You remove 4 nuts behind the brake backing plate, then use a slide hammer to pull out the axle shafts. Then the bearing retainer must be removed (cut or drill into it, the crack it with a hammer blow from a chisel), it should slide off the axle. Then use a bearing splitter and a press to remove the bearing. To install use a long pipe and press to install the new bearing and retainer. Change the seal while your in there. Hope this helps.

Posted on Apr 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change rear wheel bearings


25317835-3udur2h4av2xrpdnawrm5shi-5-0.jpegRemove wheel,brake caliper & bracket,disconnect speed sensor & remove hub wheel bolts (Wheel bearing/hub is an assembly)

Dec 11, 2014 | 2004 Mini Cooper

1 Answer

1999 plymouth breeze. step on brakes and the front brakes have a bad pulsing to them. previous owner hab brakes done rotars turned and pads replaced. any suggestions on how to address this problem


Symptom: Brake Pedal Pulsates Change When: Braking Change Where: Passenger Compartment Change -->lg-bl.jpg lg-br.jpg
Priority Action Part Type Cause 1 Inspect Brake Drum Specs Brake Drum Out of Adjustment, Out of Round, or Cracked. 2 Inspect Brake Drum Unevenly Worn or Out of Round Brake Drum(s). 3 Inspect Brake Rotor Incorrectly Machined Brake Rotor. 4 Inspect Wheel Bearing-Front Incorrectly Tightened or Installed Wheel Bearing. 5 Inspect Wheel Bearing-Rear Incorrectly Tightened or Installed Wheel Bearing. 6 Inspect Wheel Nut Loose, Worn, or Damaged Wheel Nut(s). 7 Inspect Rear Axle Bent Rear Axle.

Apr 13, 2013 | Plymouth Breeze Cars & Trucks

1 Answer

Rear wheel bearing 2002 toyota hihlander


On front wheel drive models, the rear hub bearing is an assembly that bolts to the spindle.
Not sure about AllWheelDrive models.

Jun 29, 2012 | 2002 Toyota Highlander

1 Answer

Mazda mpv 2006 repack wheel bearing


There is a little difference between the front and rear. The days of packing wheel bearing is almost over. The front bearing you have to pull the hub and change to bearing. The rear wheel you have to change out the hub bearing and all. The front is a sealed bearing and not serviceable. Please rate my answer so I am rewarded points for it.

Jan 29, 2012 | Mazda Cars & Trucks

5 Answers

Symptoms of rear wheel bearing failure on a 1999?


Jack up the rear of the car and try wiggling the wheels. They should be fairly tight.

Oct 27, 2009 | 1999 Ford Taurus

1 Answer

How to change a rear wheel bearing on a 1994 toyota camry


The rear wheel bearing on a toyota camry is replaced by replacing the wheel bearing and hub as a unit. this is a design change as compare to older models with two piece wheel bearings. Scotch drive wheels. Remove rear wheel. Remove rear brake drum. (note: if emergency brakes are applied you will not be able to remove brake drum) Remove dust cap and hub retaining nut. Hub should slide off as unit. Replace hub with new unit. Installation is reverse of removal.

May 30, 2009 | 1994 Toyota Camry

3 Answers

How do you change rear wheel bearing on a 2004 nissan sentra


Yes it is as easy as it looks. If you had the tire off and figured out that it looks easy, you shouldn't have much problem.

Mar 21, 2009 | 2002 Nissan Sentra

1 Answer

How to change rear wheel beqarings in a 2000


pretty simple they have rotors like front so remove caliper and rotor. make sure rotor is clean when u put new seal and bearings in. also hand pack wheel bearings with grease.

Feb 25, 2009 | 2001 Mitsubishi Galant

Not finding what you are looking for?
2007 Jeep Liberty Sport Logo

183 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...