Question about 1991 Chevrolet Corvette

Open Question

How to remove passenger door panel 1991 corvette

Cannot remove door release handle or lock unlock manual slide.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: 1992 corvette Lt1

You have to remove the door lock knob to get to the screw. Make sure door is unlocked,then you take an pull the knob outward til pops off.Then you should be able to remove the screw.

Posted on Oct 19, 2008

  • 75 Answers

SOURCE: remove inside door panel without breaking it

they have push in clips that hold the panel on the door you can pull it off with your hand or go to parts store and buy a door panel removal tool
PLS take time to rate this solution and by the way you will probably need to buy new push in clips to hold panel on

Posted on Feb 17, 2009

cadman000
  • 607 Answers

SOURCE: Removing manual window handle at door panel

Uses a "c" clip to secure window handle. Requires a special clip removal tool, that can be purchased at the parts store. Hope this helps

Posted on May 23, 2009

polarcycle
  • 1392 Answers

SOURCE: Driver and Passenger auto door locks are inop.

Sounds like bad wiring, or bad door lock actuators. Check for power while locking/unlocking the doors.

Posted on Jun 29, 2009

  • 1986 Answers

SOURCE: How do you remove inside door panel.

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Backdoor is unlocked on passenger side, but wont open


Sounds like you have a rusted door lock in that door, inside panel will have to be removed to access the lock assembly!

Mar 17, 2014 | 1991 Buick LeSabre

1 Answer

How to take the door panel off


Hi Austen, The general rule is as follows. Unscrew the door release handle cover and remove it. Look along the arm rest and locate the holes or the covers hiding the holes, remove the covers and with a medium size star screw driver remove the screws. Slide a flat blade at the bottom of the panel and gently lever the panel away from the door until you hear the sound of the clip releasing. Slide the flat blade along until the next is reached. Continue all along the panel and up the sides. Remove the rods or cables from the interior handle and lock mechanism. Lift the panel upwards and away from the upper lip of the door and your done! When assembling align the clips and push them home with a gentle pressure. Regards John

Apr 24, 2012 | 1997 Oldsmobile Achieva

1 Answer

The passenger door on my 1991 Honda wagon will not open. It has power locks. They work. The door handle does not release the latch that holds the door closed. How do I get it free again?


the electric actuator has a rod connected to it in order to unlock door , rod could have came off or actuator is clicking but not working.(moving) while have to remove panel to watch operation of lock.

Mar 28, 2011 | Honda Accord Cars & Trucks

1 Answer

Need to put passenger miror on. i need help to show me how to take the door panel off.


Section 01-05: Trim, Interior 1998 Windstar Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/22/1999 Trim Panel, Door Front
Removal
  1. Remove door latch cover by prying from top edge and pulling trim free of retaining clips and sliding trim away from latch.
  1. Remove portion of armrest containing door lock switch and window regulator control switch (14529) by pulling straight up.
  1. Remove rear view outside mirror mounting hole cover assembly by prying at top and pulling upward to release double-sided clip.


    Trim Panel


    ar0885a.gif


    Item Part Number Description 1 23942 Front Door Trim Panel 2 56908-S58 Screw (1 Req'd), Right Door 56906-S58 Screw (1 Req'd), Left Door 3 18B978 Radio Speaker Grille Name Plate 4 56911-S58 Screw (1 Req'd) 5 17D720 Cover Assembly Rear View Outside Mirror Mounting Hole
  1. Remove screw attaching front door trim panel (23942) to front door (20124) under switch plate.
  1. Remove two screws located at bottom of front door trim panel.
  1. Disconnect the door lock switch (14028) and window regulator control switch electrical connectors.
  1. Remove door window regulator handle if equipped by unsnapping and pivoting away the handle cover from base to expose retaining screw. Remove screw from the door window regulator handle.
  1. Pull front door trim panel from the top to release hooks from front door .
  1. Remove front door trim panel.
Installation
  1. Replace any bent or damaged fasteners.
  1. Follow removal procedure in reverse order.
Body Side
Removal
  1. Remove door handle retaining clip by sliding a shop towel between handle and door trim. With tension on the cloth, pull one end of the cloth so it slides between the handle and the door trim. If handle does not come out, reverse direction.
  1. Unfasten 13 christmas tree fasteners using double-acting spring-loaded trim removal tool and pull body side trim panel from body side door.
  1. Remove forward and rearward mating sections from under window trim.
Installation
  1. Replace all christmas tree fasteners.
  1. Follow removal procedure in reverse order.
  1. For installation of handle, install clip to handle, then push handle onto shaft to snap in place.


    r11176a.gif

Back
Removal
  1. Disconnect rear window defroster wires.
  1. Remove the liftgate window garnish moulding as described.
  1. Remove screws attaching liftgate handle to liftgate and liftgate inside trim panel.
  1. Using Rotunda Windshield and Moulding Trim Removal Kit 107-R0401 or equivalent, pry pushpins retaining liftgate trim from the liftgate.
  1. Remove liftgate trim.
Installation
  1. Follow removal procedure in reverse order.


    Liftgate


    r10441a.gif

2010&c18=modelyear&c35=wsm%2ctrim%20panel%2c%20door%2csww%2c01-05%2cremoval%20and%20installation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=405&ct=lan&hp=n&[aqe]

Mar 07, 2011 | 1998 Ford Windstar

1 Answer

2000 cadillac deville remove door panel


2000-2001 Deville Door Panel Removal:

1. Position window fully downward and ensure manual lock knob is in unlock position.
2. Disconnect locking clip at front of manual lock knob, by insertingsuitable flat bladed tool into top service notch.
3. Remove manual lock knob.
4. Remove inside handle bezel by holding inside handle to open position, inserting sutiable flat-bladed tool at front lower corner and prying outward.
5. Remove bezel.
6. Remove inside door handle mounting screw.
7. Disconnect eight retainers around outside edges of door trim panel using clip zip tool No. J-36796, or equivalent.
8. Slide door trim panel upwards to release alignment datums, eight retainers, armrest steel retainer clips and inner belt mouldings (see fig #7 amd #8).
9. Disconnect electrical connector(s).
10. Reverse procedure to install.

23785ad.jpg

Hope this help (remember rated this).

Mar 28, 2010 | 2000 Cadillac DeVille

1 Answer

Cant remove door pannel on driver side 04 gmc seirra


1. Remove the door handle bezel.

2. Insert a flat-bladed tool between the door handle bezel and the trim panel in order to release the handle bezel tab retainers.

3. Remove the door trim panel upper extension.

4. Release the upper extension by pulling outward on the front edge in order to release the upper retainer clips.

5. Remove the upper extension from the trim panel by lifting up and out.

6. Using a suitable flat bladed tool, gently pry the manual lock lever from the door trim panel. Remove the trim panel screw.
*Remove the screw (2) from within the opening where the manual door lock lever resides.
*Remove the screw (3) from the opening in front of the armrest.
*Remove the screw located beneath the map pocket, if equipped.

7. Carefully slide the trim panel up in order to release the retainers from the door. Disconnect the electrical connectors.

Note: the top part of the door panel is not separate from the bottom. The "upper extension" is just the small triangle piece directly behind the mirror on the interior.

Simplified instructions
Remove the bezel around the door handle.
Pry out the manual lock.
Remove the 3 or 4 screws depending on options
Slide the door panel up off of the engagement tabs.

Good luck and thank you for using Fixya.

Mar 16, 2010 | 2004 GMC Sierra 2500

1 Answer

How do you remove the inside paneling to fix a broken door handle?


4-Cylinder Engines
  1. Remove the screw in the door handle trim, slide the handle assembly forward, and out to access the lock rod clip. Release the clip, disconnect the door lock switch and remove the door opener handle assembly.
  2. Carefully pry off the cap(s) in the armrest pocket, then remove the screw(s).
  3. Carefully pry off the cap under the armrest and remove the screw.
  4. Using a suitable trim panel removal tool, unsnap the door panel from the door frame.
  5. Unplug the electrical connectors for the power windows, power mirror and courtesy light.
  6. Carefully lift the door panel up and away from the door frame.
  7. Installation is the reverse of the removal procedure.

V6 Engine
  1. Remove the screw in the door handle trim, slide the handle assembly forward, and out to access the lock rod clip. Release the clip, disconnect the door lock switch and remove the door opener handle assembly.
  2. Carefully unsnap the rear of the speaker grill, lift and pull back to release it and remove the grille.
  3. Remove the panel mounting screws located around the perimeter of the speaker.
  4. Remove the cap and screw in the pull pocket of the armrest.
  5. Slide the pocket back slightly to release the front hook, then lift up, detach the electrical connectors and remove the pocket assembly.
  6. Using a suitable trim panel removal tool, unsnap the door panel from the door frame.
  7. Carefully lift the door panel up and away from the door frame slightly and disconnect the speaker connector.
  8. Installation is the reverse of the removal procedure.

Oct 13, 2009 | 1999 Honda Odyssey

2 Answers

Sliding passenger door will not unlock/ open


I assume you mean a 1991 Previa (that was the first year of the model). It is likely you have broken a small spring inside the door that connects the handle to the latch. The only way to tell is to remove the inner door panel (two screws: one under the door handle and one midway along the upper part of the interior door structure then pull out and up).

Apr 04, 2009 | 1991 Toyota Previa

1 Answer

Lock wont open!


You have to remove the door panel and manually move the lock release rods inside of the door it could prove to be vary difficult. A body shop is the next step if this proves worthless.

Jan 28, 2009 | 2001 Oldsmobile Silhouette

Not finding what you are looking for?
1991 Chevrolet Corvette Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...