Question about 2004 Chrysler Crossfire

Open Question

Removing accelerator pedal on a chrysler crossfire

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 Chrysler crossfire won't go into gear please help ASAP!!


It's the brake pedal switch that has either a broken wire or needs to be replaced. They are cheap and only take about 15 to replace.

Jan 31, 2013 | Cars & Trucks

1 Answer

I need help i have a 2007 crossfire conv.my tail lights dont work


Your "Stoplight Switch" (aka Brake light switch) has failed - this is the switch that is operated
each time you depress
the brake pedal - as you can imagine, it gets a lot of use, and these switches often fail.
Here a picture of your 2004 Crossfire brake light switch ($17.95 at www.autopartsdealer.com)

archaeology_3.jpeg

Feb 20, 2011 | 2004 Chrysler Crossfire

1 Answer

Passenger side headlight assembly removal, is there more than 2 bolts, if so where


You can replace the headlights on your Crossfire easily by yourself. headlight image by Carbonbrain from Fotolia.com

When a headlight burns out on your Chrysler Crossfire, you do not need to rush to the repair shop to have it replaced. You can access the headlights in your Crossfire from within the engine compartment, allowing you to change the headlight yourself. The Crossfire uses an H7U headlight bulb, which you can find at auto parts retail stores or at a Chrysler dealership.
Difficulty: Easy

  1. 1 Open the hood of your Crossfire to gain access to the headlight assemblies. Press down on the tab on top of the light assembly cover. Remove the cover and set it aside.
  2. 2 Pull the electrical connection free of the bulb socket. Press the spring clamps securing the bulb into the light assembly. Pull the bulb straight out of position.
  3. 3 Insert the new bulb in the same position. Ensure that the spring clamps secure the bulb. Press the electrical connection into place.
  4. 4 Replace the light assembly cover and press it into position until it clicks, securing it in place. Repeat the same process on the opposite headlight if required. Close the hood and test the headlight operation.



Dec 12, 2010 | 2004 Chrysler Crossfire

1 Answer

Resivior is cracked or broken on a 2005 Chrysler Crossfire... How to get to it to repair or replace it


TAKE OFF PASSENGER WHEEL AND PLASTIC GUARD BEHIND WHEEL. JUST REMOVE ONE BOLT AND PULL OUT RESERVIOR. REPLACEMENT IS $100.

Jun 17, 2010 | 2005 Chrysler Crossfire

1 Answer

2004 Chrysler crossfire stuck in park and cannot tow


remove the shift solenoid by the shift cable inside the vehicle. then wire up the solenoids lock to the shifter to tow

Jun 09, 2010 | 2004 Chrysler Crossfire

2 Answers

2006 chrysler pacifica accelerator pedal sticking at the beginning of depressing the pedal.


carbon buildup in the throtle body is most likely the problem you need to remove the air cleaner and buy some card cleaner. there ia a butterfly valve in the throat of the assembly that will have a carbon ring built up around it use the carb cleaner and a tooth brush to remove it this happened to my pacifica I could not believe it was something so simple I went through lubricating all the cables before I found the real problem

Mar 19, 2010 | 2006 Chrysler Pacifica

1 Answer

2004 CROSSFIRE 52,000 MILES, CAR STALL AT IDLE, HESITATES WHEN PUSHING GAS PEDAL DIED TWICE WHILE IDLING. INJECTORS? FUEL FILTER? AIR FILTER?


This happened to me at 53,000 miles. Its your air flow sensor. This runs at about $200 for the part plus labor.

Oct 29, 2009 | 2004 Chrysler Crossfire

1 Answer

Fuel filter


It's under the car. It most likely has a splash shield covering it, and you might have to remove that first. Usually it will be towards the rear of the car, and near the fuel tank.

Feb 21, 2009 | 2004 Chrysler Crossfire

1 Answer

Fix Brakelight on Chrysler Crossfire 05


They Are Removed From The Inside. On The Inside Of The Car Find The Opposite Side Of Where The Light Is. There Will Be Either Carpet Or A Panel There Remove That And It Will Give You Full Access To The Lights. Use A Twist And Pull Motion To Remove The Light From Its Housing Then Replace The Bulb.

Jan 27, 2009 | 2004 Chrysler Crossfire

1 Answer

Manual shift knob removal for chrysler crossfire


I think there is a set screw in the side you have to loosen and then unscrew knob

Oct 18, 2008 | 2006 Chrysler Crossfire

Not finding what you are looking for?
2004 Chrysler Crossfire Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...