Question about 1991 Chevrolet Suburban

Open Question

Trying to remove a starter on a 2009 Hino 338

I can only find 1 bolt & there's at least 1-2 more?

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 65 Answers

SOURCE: Bad starter. how do you remove. how many bolts are there??

once you have located the starter ther are two bolts and two wires the bolts are located directly accross from eachother on each side of the starter the wires are on the back of starter hope i could help

Posted on Mar 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I'm trying to remove the transmission because it needs to be rebuilt. I cannot locate the bell housing cover however in order to remove the torque converter to drive plate bolts. Can you assist?


There is an inspection plate under the car at the bell housing. Remove the bolts and hand turn the engine over and start removing these bolts you see.

Mar 08, 2016 | Ford Cars & Trucks

2 Answers

How do i remove a 2006 chevy cobalt starter?


Some starters have 2 bolts and some 3 . Make sure your battery is disconnected. Remove he battery wires and some times you have to wiggle it to get it to move . Run your hand all around the starter to make sure all the bolts our out.

Jun 10, 2014 | 2006 Chevrolet Cobalt

1 Answer

Starter on toyota tundra2009


First remove the battery terminal, disconnect the wires from the starter, then remove the two bolts

Mar 27, 2013 | Cars & Trucks

1 Answer

Just wanna change out the starter in a 2009 Hyundai sonata i see it on the engine but its hard to reach how do i get to the starter


There's only 2 bolts holding the starter on, you may need to use a universal swivel and an extension on the socket to reach the bolts. Once you remove those two bolts the starter should pull right out. The swivel looks like this.
http://www.istockphoto.com/file_thumbview_approve/139504/2/Swivel_Socket_7_16.jpg

May 04, 2011 | Hyundai Sonata Cars & Trucks

1 Answer

I am trying to remove starter from 1998 corolla. Removed battery & starter cables, one bolt on same side as wire harness. Online said need to remove TWO bolts, on opposite sides from each other. Can't...


put your finger on the hole where the one bolt was. Run it around the edge of the starter until you run into the other bolt. You might need to remove it be sense of touch...

Jul 07, 2010 | 1998 Toyota Corolla

1 Answer

Trying to remove the Starter


Well before you wind up dropping the trans,lol, check the front side of the trans in front of the starter. There's usually a bolt or or nut on a stud. There's only 3 bolts or 2 bolt & that stud holding it in. Check autozone's site for a diagram or buy a Hayne's manual from any parts store.

Jul 22, 2009 | 1999 Mitsubishi Galant

1 Answer

Trying to remove the starter on a 1991 SaturnSL


no there is not a special tool need more info go to collisionrepairadvice.com for more
1991 Saturn SL L4-1.9L DOHC VIN 7 Vehicle Level a_003366.gif Starting and Charging a_003366.gif Starting System a_003366.gif Starter Motor arrow1.gif Service and Repair arrow2.gif blnk_spc.gif Service and Repair Notes
  1. Disconnect battery ground cable.
  2. Remove air inlet tube and fresh air hose, on DOHC models, lift resonator upward to disengage from engine support bracket.
  3. Remove upper starter attaching bolt through access hole near intake manifold support bracket.
  4. Raise and support vehicle.
  5. Using suitable pliers, remove starter shield pin, then lift shield upward to release from solenoid.
  6. Disconnect starter electrical connectors and position aside.
  7. Remove lower starter attaching bolt.
  8. Remove rear starter support bracket attaching bolt.
  9. Rotate starter until bracket clears axle shaft support bracket, pull rearward toward lefthand side of vehicle to remove.
  10. Reverse procedure to install. Torque starter attaching bolts to 26 ft. lbs., starter bracket bolts to 22 ft. lbs. and starter solenoid terminal to 3 ft. lbs.

Apr 11, 2009 | 1991 Saturn SL1

1 Answer

Bad starter. how do you remove. how many bolts are there??


once you have located the starter ther are two bolts and two wires the bolts are located directly accross from eachother on each side of the starter the wires are on the back of starter hope i could help

Mar 23, 2009 | 1986 Chevrolet Celebrity

1 Answer

Starter


You'll find 2 bolts that attatch the starter to the trans. housing. Remove the wiring from the starter and the bolts, one of which is towards the top of the starter and one near the bottom.

Jun 21, 2008 | 2001 Chrysler Town & Country

Not finding what you are looking for?
1991 Chevrolet Suburban Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...