Question about 1996 Mercury Villager

1 Answer

Air in rear does not work and doors sometimes lock by themslves

Information on how to regas A/C is hard to find ,,,,,,,,the passenger side window failed ,,,,the tract gear fails to engage,,,,

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 266 Answers

It will have its own little sys in the rear look in the back behind tires in the 2 corners or u will have to take off rear panels to access

Posted on Jun 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 le sabre, power windows, door locks, side mirrors, not working all of a sudden


All - driver - passenger - front an back ? Look for broken wires inside the rubber boot from the body to the door ,driver side !

Power Windows Operation
Power Windows
The vehicle is equipped with power windows controlled by the door modules. The DDM receives a window switch request, over the SBI serial data, from either the passenger door module wired to the window switch pressed or from the driver door switch assembly. The DDM checks the Class 2 serial data to see if the status information is correct (i.e. ignition switch position) to permit window operation.
If the status information to permit window operation is correct, the DDM sends the command to the door module controlling the window to move the window as requested.
Windows Power and Ground
The windows are powered by discreet power and ground circuits. These circuits are in the same dedicated connector as the window motor drive circuits.

PWR/WDO 30 amp circuit breaker located in the rear fuse box ,DRVMDL fuse 10amp located in the same rear fuse box . This power the driver door module (computer )

The vehicle is equipped with power door locks. Each lock actuator is powered and controlled by the door module mounted in the individual door. The driver door module (DDM) is the master control for the door lock system but the rear integration module (RIM) contains the program that determines when the lock functions are permitted.
The exterior key cylinders are wired to either the DDM or the passenger door module (PDM), depending on the location of the key cylinder. The interior lock switches are wired to the driver door switch assembly (DDSA) and the PDM. The DDSA and the PDM send the lock switch requests to the DDM over the simple bus interface (SBI) serial data circuit. The DDM then sends the lock requests to the RIM over the Class 2 serial data circuits.
The door lock operation modes are controlled by the rear integration module (RIM). The RIM examines the requested function from the DDM, or the remote function actuator (RFA), as well as the transmission shift selector position and the ignition switch position information available over the Class 2 serial data circuits. The RIM determines if a locking function is permitted, and commands the DDM to perform the function permitted. The DDM then sends commands to the rest of the door modules via the SBI to implement the selected locking function.
All programmable modes of lock system operation are stored in the RIM. The RIM checks the lock function program selected against the lock requests, the transmission selection and ignition key switch condition to determine if the requested function is permitted. If the requested function is permitted, the RIM then commands the DDM to perform the lock function over the Class 2 serial data circuits. The DDM commands the individual door modules to perform the lock function over the SBI serial data circuit.


GOOD luck your going to need it !

Mar 13, 2017 | 2000 Buick LeSabre

1 Answer

Both rear electric door locks are malfunctioning. Drivers side rear door lock works good when it is cold. the same was true with the passenger rear door lock. now that one will not work at all. the...


to see if it is a switch problem see if the locks work from their respective doors, if the locks work from the switch's on the back doors and not from the drivers switch then the drivers switch is bad. If the locks don't work right from any of the switches then the door lock solenoids are bad. the solenoids are not too hard to change if you are mechanically inclined, switches are not too hard either

Feb 09, 2014 | 2008 Chevrolet Impala

1 Answer

Buick 2002 LaSabre Custom all windows do not go up and down, door lock/unlock switch drivers side does not work(passenger & rear doors lock/unlock door switches work, trunk release button does n


coulb be the control switch on your panel you can take the door panel off and check for loose connections and try to test for continuity. if you dont know how take it to a shop and have them diagnose the electrical. im quite sure it the switch that burnt out

Oct 24, 2012 | 2002 Buick LeSabre

1 Answer

I have a 08 chevy avalanche the driver side front and rear door locks won't work when I use my keyless entry button or on the inside driver panel. Could it be a fuse? Passenger side works fine I try...


Do the power windows work ? DDM - driver door module fuse 15 amp - location is the instrument panel fuse box , plus LT DR circuit breaker 25 amp. Circuit breakers rarely go bad . The power locks are controlled by electronic's .The passenger side has another power supply ,that's why they still work .
Door Lock System Components
The power door lock system consists of the following components:
• The driver door switch (DDS)
• The passenger door switch (PDS)
• The body control module (BCM)
• The driver information center (DIC)
• The rear door lock/unlock relay (LBEC)
• The reversible door lock actuators in each of the doors and liftgate

The front power door lock switches are integral components of the driver door module (DDS) and passenger door module (PDS). The switches are 2 position normally open rocker switches. When placed in either the lock or unlock positions, the switches provide a direct input to the DDS or PDS. The DDS or PDS monitors these inputs and sends a LAN message indicating a change in the switch's respective position. Modules which activate the power door lock motors receive the LAN message and activate the motor in the appropriate direction to lock or unlock the vehicle's doors and liftgate. The rear door lock switch provides a lock and unlock signal to the body control module (BCM). The BCM upon receipt of a lock or unlock signal will control the rear door lock/unlock relay and also send a LAN message to the DDS and PDS to perform the appropriate function.
The modules which activate the power lock motors are:
• The DDS (driver door lock actuator)
• The PDS (passenger front door lock actuator)
• The BCM (both rear door lock actuators and cargo door/liftgate)
The DDS and PDS are directly connected to the respective door lock actuator through the door lock motor lock and unlock circuits. Once a door lock or unlock request has been received, the module will supply battery voltage to one side of the actuator and ground the other causing the doors to lock or unlock.
The rear passenger and endgate doors are controlled by the BCM through the rear door lock/unlock relay which is incorporated onto the printed circuit board in the LH BEC. The BCM controls the unlock relay by providing ground to energize the coil and controls the lock relay by providing battery voltage to energize the relay coil. The energized the relay and allows voltage to be applied to either the door lock motor lock or unlock circuits. Since the other side of the door lock actuator is connected to the normally closed contacts of the opposing relay to ground, the doors lock or unlock.

It's possible you have broken wire or wires inside the flex boot from the body of the vehicle to the driver's door . This happens a lot .
Fuse Block - I/P instrument panel
Left of the I/P behind the side trim panel

Mar 04, 2018 | 2008 Chevrolet Avalanche

1 Answer

Driver's side window will not work. Door locks work.


My mechanic took out the panel on the driver side control because my right rear passenger window would not work after disconnecting the battery (but the control on the passenger rear door works) and when he put it back, it worked..it's possible it's just a loose wiring connection. My car is a 2006 Lexus RX330 with 58K miles on it.

Aug 02, 2010 | 2001 Lexus RX 300

1 Answer

Passenger front /rear windows will not work 99 jeep gr cherokee


ill suggest theres a broken wire between the drivers door and the body in that accordian looking thing.

Sep 06, 2017 | 1999 Jeep Grand Cherokee

1 Answer

Drivers side window control cluster


The control may have gone bad... You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. Then you can disconnect the controls and test them

Aug 09, 2009 | GMC Denali Cars & Trucks

1 Answer

1994 buick regal-passenger door lock will not operate with electr


first check or replace the relays in the fuse panel under the dash for those two circuits and see if that fixes it

Feb 23, 2009 | 1995 Buick Regal

1 Answer

Rear side windows


This may be just a case of inadvertently hitting the window lock out n th driver door window switch by mistake. Check that first. Here's some background on window operation

Principles of Operation
The driver power window regulator motor is controlled directly by the master window/door lock/unlock switch (and its integrated "auto down" module). Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The driver power window regulator motor is a reversible motor that is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The passenger power window regulator motor is controlled directly by the passenger power window switch and can also be controlled by the master window/door lock/unlock switch. Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The passenger power window regulator motor is a reversible motor, which is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The power rear quarter glass is also directly controlled by the master window/door lock/unlock switch. The power rear quarter glass power latches also utilize reversible motors. The power rear quarter glass power latches are operated by applying power and ground to the motor leads to open the window, and then reversing polarity on those same leads to close the window.
Symptom Chart Condition Possible Sources Action
  • All windows are inoperative
  • BJB Fuse:
    • F20.
  • Circuit.
  • Power window relay.
  • Front door power window switch.
  • GO to Pinpoint Test A .
  • Single power window is inoperative
  • Front door power window switch.
  • Front door power window regulator.
  • Circuit.
  • Driver door power window switch.
  • GO to Pinpoint Test B .
  • Vent power window is inoperative — quarter window glass power latch
  • Circuit.
  • Quarter window glass switch.
  • Quarter window glass power latch.
  • GO to Pinpoint Test C .
  • The one touch down feature is inoperative
  • Master window regulator and door lock switch.
  • INSTALL a new master window/door lock/unlock switch. REFER to Switch—Master Window Door Lock/Unlock .
  • The back window will not defrost
  • CJB Fuses:
    • F30 (10A).
    • F32 (20A).
    • F34 (20A).
  • BJB Fuse:
    • F27 (45A)
  • Circuit.
  • Heated back window switch.
  • SEC/timer module.
  • Rear window defrost relay.
  • GO to Pinpoint Test D .
  • The back window defrost will not shut off automatically
  • SEC/timer module.
  • Circuit.
  • Rear window defrost relay.
  • GO to Pinpoint Test E .

Jan 28, 2009 | 1999 Mercury Villager

3 Answers

1999 Jeep Grand cherokee


Check the wiring between the drivers door and the A pillar(the body of the car). Sometimes the harness breaks from opening and closing the door.

Nov 07, 2008 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
1996 Mercury Villager Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

gerry bissi

Level 3 Expert

4376 Answers

Marvin
Marvin

Level 3 Expert

81424 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...