Question about 2005 Chevrolet TrailBlazer

Open Question

Crankshef Cranshef torque for 4.2 liter

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the power of engine hyundai sonata sedan 2007


Hyundai Sonata 2007 have the two variants which are Sonata GLS and Sonata SE. So check out the engine power of the Hyundai Sonata, which are as follows,

=> The Sonata GLS is powered by a 2.4-liter 4-cylinder engine that makes 162-hp and 164 lb.-ft of torque at 4,250 rpm.

=> The Sonata SE and Limited are powered by a 3.3-liter V6 engine that pumps out 234-hp and 226 lb.-ft of torque at 3,500 rpm.


2007_hyundai_sonata_angularfront-wlnk1dj5o4kpi2hgqjoc4lln-3-0.jpg

Oct 30, 2017 | Hyundai Cars & Trucks

1 Answer

Head torque specifications


Torquing the head bolts is done in 4 steps.
step 1 14 ft/lbs
step 2 36 ft/lbs
step 3 49 ft/lbs
step 4 retourque bolts 1 and 2 at 49ft/lbs.
Use this diagram for the torque sequence.
53fa97e9-4910-4532-9ee1-f6b8fdc76831.png

Aug 14, 2014 | 1998 Honda Civic

1 Answer

1995 camry goes in gear but won't move. I think


The 1995 Toyota Camry was available with either a 2.2 liter 4-cylinder, rated at 125 horsepower (130 in 1992-1994) and 145 lb-ft of torque or an aluminum block 3.0 liter V6, rated at 188 horsepower (185 in 1992) and 203 lb-ft of torque.-----------------------------------------------------------------------------------------
BENZ STAR C3

Jan 31, 2013 | Cars & Trucks

1 Answer

What is the torque settings on a 3.4 liter engine 94 camaro. replaced the heads and gaskets


Torque sequence --------- ' 6 2 3 7 ' ' 5 1 4 8 ' --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

I hope this helps you and good luck

Mar 25, 2011 | 1994 Chevrolet Camaro

2 Answers

Rod bearings torque on cap nuts do you know what it is torqued at


Hello terrychadwic

If you have the 3.3 or 3.5 engine the torque is 40 foot pounds + 1/4 turn.

Regards,
netvan

Mar 04, 2011 | 1996 Chrysler Concorde

2 Answers

I need to know the torque specs for the cylinder head bolts for a 1.6 liter dovc 2005 kia rio


What about the torque pattern, or is there an indepth manual online somewhere?

Timing belt broke, now I am on rebuild.

Mar 16, 2010 | 2005 Kia Rio

1 Answer

Cant find the right bolt torque sequenceor bolt


Cylinder head bolts for 2.4 doch in ft\lbs
Step 1 .....................................................................................25
Step 2......................................................................................50
Step 3.......................................................................................50
Step 4.....................................Tighten an additional 1/4 turn (90-degrees)


the order is shown in this image:http://yfrog.com/2ocylinderheadj

Jan 21, 2010 | 1996 Dodge Stratus

1 Answer

Had fire and need to know where to fine crankshef positioning sensor plug on wiring harness on 96 ram 1500 v6 3.9


The crankshaft positioning sensor should located around the crank pulley. The plug in should just be a few inches away from the sensor itself.

Mar 24, 2009 | 1996 Nissan Maxima

2 Answers

Does the upper intake manifold have to be torqued


No, but it is a real good idea. I would,it keeps you from breaking stuff.

Mar 01, 2009 | 1999 Dodge Avenger

2 Answers

Need to know cylinder head bolt torque specs


Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
2005 Chevrolet TrailBlazer Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...