Question about 1983 Chrysler New Yorker

1 Answer

Engine shaking at idle state

Engine fault code is p2311. What next because engine shakes at idle and very worst when engaged.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 752 Answers

Hi Edwin, I'm glad to help. P2311 means: Ignition Coil Secondary Circuit Condition on Cylinder Number 4. FIRST: I'd try replacing the spark plug and plug wire for number 4 cylinder and see what happens. If that doesn't fix it then more diagnostics will be needed. Hope this helps and have an awesome day Edwin.

Posted on Jun 16, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 979 Answers

SOURCE: 94 chrysler concorde

Possible vacuum leak at EGR or PCV, or even at the intake plenum gasket is where I'd check first...accordianman

Posted on Jul 28, 2008

  • 11 Answers

SOURCE: TAPPING AND SHAKING

i have made the same mistake before, without the proper tools it is very dificult to keep all the timing marks where they are supposed to be when releasing the tensioner( one cam will turn one way and the other the opposite) this will throw the cam timing out just enough so it will start but will run very bad, unfortunately the only fix for this is to pull the cover back of and do it again

Posted on Apr 26, 2009

pippall
  • 1486 Answers

SOURCE: 2001 Chrysler LHS engine misfire

You have a spark plug or wire breaking down under pressure.I would have them changed.

Posted on Sep 16, 2009

  • 83 Answers

SOURCE: Misfire

It may be that there is carbon build up. Check the bulletins for you car.

THIS BULLETIN SUPERSEDES TECHNICAL SERVICE BULLETIN 09-005-05, DATED
DECEMBER 2, 2005, WHICH SHOULD BE REMOVED FROM YOUR FILES. THIS IS A
COMPLETE REVISION AND NO ASTERISKS HAVE BEEN USED TO HIGHLIGHT
REVISIONS.
SUBJECT:
Multiple Cylinder Misfire Or Rough Idle
OVERVIEW:
This bulletin involves rotating all engine exhaust valves, replacing the valve spring retainer
locks with a new design to increase valve rotation at lower RPM, inspecting/replacing the
MAP sensor (as necessary), and decarbonizing the combustion chamber.
MODELS:
2004 - 2006 (CS) Pacifica
2005 - 2006 (LX) Chrysler 300/Magnum/Charger

Of course you know how much the dealer is going to be if you are out of warranty. You can try a few things which may possible help, like getting some of the mopar fuel cleaner or another good fuel cleaner, I've heard a few people resolving the issue that way. If you need a good service manual Promanuals has one relatively inexpensive.

Posted on Sep 27, 2009

  • 9 Answers

SOURCE: 2000 chrysler cirrus problems

I have the same problem with great shaking while stopped idling, but no engine light. It is worse when cold and worse when in gear. I have a 1999 Cirrus with the 2.4L engine. It works great and there are no error codes. What I have discovered is that there is something called a flex plate that goes between the torque converter and flywheel and it was cracked. It must be easy to access to inspect (more work to repair though) as the garage didn't charge me for the diagnosis. They said that the crankshaft rear seal was also pushing out. You can do both at the same time once you get it apart.

Posted on Mar 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

09 Passat epc engine light came on and car is shaking


run the fault codes
indications are injector problems either wiring , or blockage
check fuel pressure as it could also be from low fuel pressure , problem pressure regulator , blocked filter or EVAP venting problem

Aug 04, 2016 | 2009 Volkswagen Passat 2.0T

1 Answer

I have a few codes that need to know what they mean


Hello there.
Sounds like number 4 cylinder problems ;spark plug, leads. coil;

From here the general meaning of P02311 is problem with 'ignition coil 4'
http://engine-codes.com/p2311.html

From this page
http://engine-codes.com/make/jeep

Sep 16, 2014 | 2005 Jeep Liberty

1 Answer

Car shaking at idle, no engine check light


Sounds to me that you have a cylinder miss fire. Chrysler products generally set a code when a miss fire is detected. Does the shaking go away under a load (while driving) ? If the miss is always there I would focus on the ignition system and look for any vacuum leaks around the intake manifold area .

Apr 22, 2014 | 2004 Chrysler 300

1 Answer

92 Thundebird 3.8...starts hard....really rough idle in any gear...sounds loud. Almost feels as if the engine is shaking


run fault codes and look for position sensors --MAP/MAF/VAF sensor problems and fuel /injector faults.

Jan 06, 2014 | 1992 Ford Thunderbird

1 Answer

Lexus ES300 Shakes/Vibrates At 45 MPH


Major transmission problem. That's what the flashing Check Engine light means.

If the Check Engine light is on all the time, it means there is a "fault code" stored in the computer. Take it to an auto parts store (like Auto Zone) and ask them to read the codes to see what it says. They should do it for free. If they won't, go to another auto parts store.

Jan 05, 2014 | Lexus Cars & Trucks

1 Answer

Just bought a toyota passo but when idling the engine vibrates too much and shakes the car


pls check your system by using a car scanner........ then monitor your IAC valve duty ratio up when shift to D position after it's OK clean throttle body and IAC valve.good luck

Nov 15, 2012 | Cars & Trucks

1 Answer

I have a 230 slk mercedes kompressor. It begin to shake really bad when coming to stops. I waited for a while and re cranked the car the shaking did not continue. what could have caused this to happen? ...


The following are the general instructions on the start of diagnosing any electronically controlled engine or transmission problem.

The engine and the automatic transmission (transmission control is only for automatics, engine is still computer controlled no matter the transmission type) in this vehicle are computer controlled and in most cases when a fault occurs a fault code is stored in the memory of the computer control module. There are exception to this, such as the Mass Airflow Meter and fuel pressure problems. What must be done is to have all the basic testing done such as a scan of the system for fault codes as well as a check with a live data scanner tool for engine functions that are not within range of normal, a trained technician is required to know what is correct and what isn't, then based on careful diagnostics done from a factory repair manual the correct part is replaced or the wiring repaired or the computer replaced (known as the PCM or ECM,ECU), which is very rarely the problem. Other basic checks must be done as well such as mechanical problems with the engine as well as engine state of tune and mileage on the engine. The transmission can have mechanical issues as well such as no gear engagement at all or a failed pump or other pressure related problems. Also engine mechanical problems can and do cause many drive-ability related problem such as rough idle and other symptoms.

Nov 06, 2012 | Cars & Trucks

1 Answer

My truck is shaking really bad when i brake and tries to die..it is a 2002 Chevy Avalanche v8 5.3...when i hit the gas it stops shaking? please help i just bought this truck today


The following are the general instructions on the start of diagnosing any electronically controlled engine or transmission problem.

The engine and the automatic transmission (transmission control is only for automatics, engine is still computer controlled no matter the transmission type) in this vehicle are computer controlled and in most cases when a fault occurs a fault code is stored in the memory of the computer control module. There are exception to this, such as the Mass Airflow Meter and fuel pressure problems. What must be done is to have all the basic testing done such as a scan of the system for fault codes as well as a check with a live data scanner tool for engine functions that are not within range of normal, a trained technician is required to know what is correct and what isn't, then based on careful diagnostics done from a factory repair manual the correct part is replaced or the wiring repaired or the computer replaced (known as the PCM or ECM,ECU), which is very rarely the problem. Other basic checks must be done as well such as mechanical problems with the engine as well as engine state of tune and mileage on the engine. The transmission can have mechanical issues as well such as no gear engagement at all or a failed pump or other pressure related problems. Also engine mechanical problems can and do cause many drive-ability related problem such as rough idle and other symptoms.

Oct 31, 2012 | Cars & Trucks

1 Answer

Ford five hundred running on 5 cylinders


the code p 0302 refers to no 2 cylinder misfiring===causes --engine mechanical fault ---wiring--ignition / fuel system---injector--ECT/Maf sensor ---ECM
you state that the engine runs normally for several seconds so I would eliminate a mechanical fault at this stage
most misfires are from faulty injectors so reposition the injector to another cylinder and see if the miss moves along as well
if it doesn't move but stays at no 2 cylinder , then it could be a problem ECM
if you can get a substitute ECM of known good performance , swap it out and see if that fixes the fault

Mar 26, 2017 | 2005 Ford Five Hundred

2 Answers

Ford ranger 1997 2.3 engine problem


Sounds like the idle bypass valve is nfg. Try checking engine codes first. Try this link, you'll find it helpful. http://autorepair.about.com/od/troubleshooting/a/OBD_codes.htm . If you need to know how to check the codes, ask back here, I'll explain. Hope this helps.

Jan 03, 2009 | 1997 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

190 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...