Question about 1998 GMC Sonoma

1 Answer

PO113 error code on 1998 cavalier 2.4 OHC even after changing sensor and clearing original code.

Posted by on

  • dclingaman Jun 20, 2009

    Sorry I posted under wrong vehicle but it is the same engine. It runs rough at idle and uses a lot more gas. I am going to get a meter today and check for broken or shorted wires.

  • dclingaman Jul 04, 2009

    I had posted this in error but yes it was the right engine and I checked the wires with an ohm meter and found the wire was broken just inside the connector before I had a chance to read your post. Our local parts stores did not have the connector but after some hard work I finally got the pin out of the connector housing without damaging it and soldered the wire to the pin and reassembled it. Works fine now.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

How does it run?

Posted on Jun 20, 2009

  • Clint Smock
    Clint Smock Jun 21, 2009

    p0113 is for the intake air temp sensor. You said you have a 2.4 right? Not a 2.2. Have you done anything to it or had anything done to it lately. If seen these have bad connectors going into the sensor you can splice on a new one, the parts stores sell the plugs. It is the same as a coolant temp sensor plug.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Po113 code


Po113 is the air intake sensor most likely left unplugged when air filter was serviced and the APP sensor is accelerator pedal position sensor

Apr 20, 2014 | 2005 Dodge Ram 1500

1 Answer

Po113 code


old post
and its not a 1995,
only 1996+ do that code. (july1 1995 build day sure are 1996 model year.)
fact OBD2 started this day in USA> 1998 in canada.

113 means ( your mechanic )changed the air filter
and knocked the IAT sensor wires off.
for sure. its no longer plugged in for sure, or broke it.

Mar 30, 2014 | 1995 Geo Tracker

1 Answer

Code po113


Its the air intake temp sensor. You will find it in the front of the intake somewhere. I am not sure about Geo's but if you have a Haynes or similar manual it will give you this info, you could do a search on internet an find its location. It is going to be on the air intake housing. Sometimes you can do a reset on sensors, but most of the time they dont work. Since the vehicle has some miles on it just replace it. Then clear codes an watch to see if things change. Could be as simple as connector loose

Mar 30, 2014 | 1995 Geo Tracker

1 Answer

I have a Honda Accord 2004 with a code PO339, PO113 &PO344. can you assist in advice to solve these problems


p0339 is crank shaft position sensor related error. you need to be sure that its wiring is not damaged and it is not shorted somehow. if it is broken or getting broken, car may stall, or wont start att all.

p0113 is for intake air tempoerature sensor errors. that sensor measures air ehich enters the engine. it is least important. its effect may not be noticable when weather is not extremely cold.

p0334 is for knock sensor on engine. it prevent predetonation due to ignition conditions appear. it is felt when engine is under load like climbing, and engine speed is low. check for wires if it is ok replace sensor.

we can tell that temperature sensor is not directly effects other sensors.
but knock sensor and crank position sensor is to important for engine. if you have no starting issues, even cold or warm engine, invest on knock sensor first.

Nov 28, 2011 | 2004 Honda Accord

1 Answer

How to fix error code p1391 on 1998 jeep cherokee sport


did you erase the code? if code is not cleared it acst same way even if you installed a new sensor.

if not cleared, you can do either using obd2 scanner or you can just try to disconnect (-) of your battery for 15 minutes. it i will relearn every thing after 2 or 3 warm ups, and will start to idle ok.

Nov 18, 2011 | 1998 Jeep Cherokee

1 Answer

Dtc for a 2002 crown victoria codes are 430,113


HELLO the code po113 is for intakeair temp sensor this sensor is in the air flow meter sensor . p0430 is for catalytic efficiency .you should first clear codes and see if they come back

Dec 23, 2010 | Ford Crown Victoria Cars & Trucks

1 Answer

Can you tell me what code po113 is and how to fix it I have a 2000 ford focus I just changed the mass air flow censor and after two min of changing it the light came on


first unplug mass sensor make sure not corroded or a bent pin when plug back in make sure tight then unplug neg from battery for about 30 minutes will clear codes, might be the sensor itself

Sep 14, 2009 | 2000 Ford Focus

1 Answer

Error code po113


the error P0113 still comes up even after a new sensor was installed and the transmission shifts very hard. Found a break in one of the wires to the sensor. Soldered it back to gether. Found that the engine has a limit to the rpm when rev-ing in neutral.
Thanks
rkbids

Aug 05, 2008 | 2002 Chevrolet Malibu

Not finding what you are looking for?
1998 GMC Sonoma Logo

Related Topics:

312 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...