Question about 1994 Chevrolet C/K 3500

1 Answer

1994 3500hd front left turn signal won't work

Rear turn signal flashes fast. I replaced the bulb still not working. The hazard flashers stopped working at same time and I replaced the hazard flasher relay but neither one are working.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Expert
  • 73 Answers

The wire feeding the front left turn signal is likely crimped or stretched and touching the body somewhere. Do you best to trace the left front turnsignal wire back as far as you can - even just jiggling it might give you short term solution (although it will probably come back).
The fast flash of the rear light is because the short up front is letting too much electricity run through the flasher module. This makes it run too fast. Find the short up front, and both problems will be solved.

Posted on Apr 24, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 401 Answers

SOURCE: Signal Lights - flasher...

Hi it sounds like the multifuntion switch
never had one on a monte carlo before but lots of grand am and malibu
hope this helps

Posted on May 13, 2009

  • 52 Answers

SOURCE: Left turn signal blinks fast in rear and regular in front

the bulb is blown out. you need to change it. also if the bulb is not blown out or if the blinker still blink fast after you change the bulb then you have a ground problem. just remove that blinker light and check the ground wire on it. if you need to replace it and find a good groun on the car. you should be fine. this is all it is .

Posted on Jun 04, 2009

  • 4 Answers

SOURCE: 1997 Chevy Tahoe both turn signals stopped working

Sounds like the flasher unit to me. Normally the emergency flasher and turn signal are separate.

Posted on Jul 21, 2009

rockitman187
  • 2559 Answers

SOURCE: Left turn signal flashes fast

the flasher relay is located in the fuse panel, But you may want to check the front lights as well since all 4 of the blinkers are linked for the hazzard feature,any one of the bulbs can cause this issue.

Posted on Oct 01, 2010

sulavaca
  • 1007 Answers

SOURCE: 1994 Chevy C1500 truck. No rear brake lights

Most likely this is a brake light switch issue. Replace switch.

If your emergency flashers don't work, all flasher bulbs are fine, but flashing too fast, then check and replace Hazard light switch.

Posted on Oct 30, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 chevy blazer . Problem is the horn does not work and turn signal flashes fast on both sides.


Do you know how to do automotive electrical testing ? Do you know what a relay is and how it works ? Turn signals flashing fast , could be aburnt bulb , flasher module .
VEHICLE RELAYS Operation Diagnosis
Turn Signal Lamps
The HAZ LP fuse in the underhood fuse block supplies battery positive voltage to the multifunction hazard switch assembly. The TURN fuse in the IP fuse block supplies Ignition positive voltage to the multifunction turn signal switch assembly. With the ignition switch in the RUN or START position, ignition positive voltage is connected through the multifunction turn signal and hazard switch assembly to the flasher module which is grounded at G205. When the turn signal switch is placed in either the left or right position, the circuit is complete from the flasher module to the turn signal lamps and to ground. The flasher module then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is activated, all turn signal lamps will flash including both IPC turn indicators. The front turn signals are grounded at G111 and G112. The rear turn signals are grounded at G475 and G422 on the pickup and G450 on the utility.

Aug 26, 2017 | Cars & Trucks

1 Answer

Alpha Romeo 156 My Left hand indicator light stays on continually, does not flash. and when I turn the hazard light switch on both indicators continually glow.


Generally speaking, symptoms of a bad or failing turn signal bulb are usually the culprit...in your case, either it's the front left or rear bulb. Varies for different vehicle makes...common signs include:
  1. turn signal light staying on solid
  2. or blinking very fast
  3. or either sides of the bulbs stop blinking altogether.
To test this, make sure you reconnect everything you disconnected.
Turn the left signal light on; go to the front of the vehicle, is the turn signal bulb illuminated? If it lights up, even though it is not blinking obviously the bulb is okay. If it doesn't, replace it- problem solved. You'll do the same procedure for the rear turn signal Is that lit up? If not replace the bulb and the problem is solved.
Another common failure is when the turn signal blinks really fast, same procedure as mentioned above.
If both bulbs for the left side and right side illuminate but don't blink, the problem is in the steering column turn signal switch.
If the left or right side blinkers don't work properly at all...then check the integrated hazard warning/turn signal flasher relay- that may be defective; again, that's usually the case if both sides of the signal light don't work.
If you are blowing any fuses related to the flasher system, you have an electrical overload in the turn signal circuitry.

Feb 12, 2017 | Cars & Trucks

1 Answer

My left turn signal recently stopped working. Before ceasing to work, the turn signal (just the left) would blink very rapidly (machine gun speed).


sounds like one of light bulbs was malfunctioning and caused the flasher unit to blink rapidly and iy burned out. Replace front and rear turn lite bulbs and see if flasher flashes. if not check fuse and replace fuse. If fuse okay replace flasher unit. Good luck

Jul 08, 2016 | 1997 Plymouth Voyager

3 Answers

My left turn signal was flashing fast. I checked bulb in back left. Turn signal good but bulb below it was out. I changed that one but turn signal still flashing fast. all other bulbs look good. ??


If the front and rear bulbs flash fast also, replace the hazard switch or you could live with it. As they are working. If one doesn't work, check grounds. I just run a new ground, much easier than cutting open the harness to find the break.

May 31, 2015 | 2012 Nissan Rogue

2 Answers

1997 Dodge Neon left signal lights work great. Right side blinks very fast.


Has the car been in a fender bender ? check for wiring going to the front and rear lights to see if on has rubbed into a ground wire or the body. ( even if there has been no accident.)

Apr 18, 2013 | 1997 Dodge Neon

1 Answer

Toyota sienna turn signals blinking fast


first thing I would is check ALL of the bulbs...front and rear,usually the fast flashing is from a bad bulb causing electricity to backfeed to the instrument cluster,I would replace the bulbs first,and I doubt the t/s assy is bad, do the emergency flashers work?

Sep 23, 2012 | 1998 Toyota Sienna

3 Answers

I have a 1995 chevy cavalier and the turn signals just stay on and don't blink. I have changed the flasher and the multi function switch and still no luck


First, is it doing it on BOTH isdes or just on one side? Example: turn signnals flash OK when turning left, but only come on and stay on when turning right. If it is doing this, then you most likely have either a blown bulb or a bad bulb socket on the side that is not flashing. You need to check both the FRONT and REAR bulbs to make sure they are all functioning properly.
If it is doing it on BOTH sides, then you either have a bad flasher, or at least 2 bulbs burned out (one or more on each side).

Are you sure you replaced the correct flasher? The flasher for the HAZZARD lights is plugged into the convinience center under the left side of the dash. If this is the flasher you replaced, it is the wrong one.
The turn signal flasher is mounted to the driver's knee bolster bar near the steering column. It is held to the bar with a clip. (see diagram)

9_25_2011_3_20_38_pm.gif

Sep 25, 2011 | 1995 Chevrolet Cavalier

1 Answer

Where is the exact location of the hazard light flasher for a 1989 GMC Sierra C2500, and what is the possibility that it is the true problem behind the hazards not working? Beyond my hazards not working my...


Are you sure the right side bulbs all flash? You say you replaced all the bulbs? Why would you replace bulbs that were working? Did you have this problem before you replaced the bulbs, or after. The hazard flasher is down under the dash, left side, turn the signals on and follow the clicking noise.The hazard flasher and the turn signal flasher should be near each other, and are interchangeable. If it clicks fast, a bulb or a bad socket is usually the cause. These trucks have a lot of problems with the tail light circuit boards.

Nov 04, 2009 | 1989 GMC C2500

2 Answers

Turn signals flashing too fast


Yes, This is easy. Recall on this problem. Take into dealer for free recall solution and it will stop.

Jun 24, 2009 | 1999 Buick Regal

1 Answer

Front turning light does not work, i replaced the bulb, and when i turn the truning signal does not turn off.


Sounds like you have a bad ground. Follow the wiring harnesses under the hood and in the trunk, there should be a ground wire going to the chassis or to the body. If they are all clean and tight, you might be looking at a bad light socket.

May 28, 2009 | 1996 Dodge Neon

Not finding what you are looking for?
Cars & Trucks Logo

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...