Question about 1994 Chevrolet Beretta

1 Answer

I have a 1994 Chevy Beretta , The fuse for the signal and back up lights kept blowing and I'd see a small flash, I had to replace it several times, and finally the last time there was even a bigger flash , but the fuse didn't blow, and the signal and back up lights stopped working and I have not been able to figure out happened, I've changed the Flasher, etc..still not working....I'm hoping someone can give me some insite of what it could be ,,thanks

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 16 Answers

Boy, you have a shot out. A raw wire touching some metal, or wires touching each other. Going to have to trace your wires back to the fuse box, that is the hard part. Cross your fingers that is is found quickly.

Posted on Apr 22, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 599 Answers

SOURCE: turn signal flasher needs replaced

educated guess..flasher units (2) one for signals the other for emerg flashers usually located in fuse block under dash drivers side kick panel , glove box area ..or engine compartment near battery

Posted on Jan 13, 2009

  • 51 Answers

SOURCE: no brake or turn signals the fuse blows

what about the sockets of the lights are they rusted in the contact spot and touching the 2 positive connections

Posted on Mar 03, 2009

GM Elec
  • 1000 Answers

SOURCE: fuse blows when shift in reverse

Am I correct, the turn signal fuse is blowing when you put the manual shifter in reverse?
Let me know.
Regards

Posted on Mar 26, 2009

co7196
  • 3433 Answers

SOURCE: Fuse for trailer right turn signal and brake blows intermittently

abad ground on that tail light unit could affect current load when turn and stop are used simultaneously. Although one side only is affected make sure of good grnd between trailer and tow vehicle. focust on the tail light unit in question. Replace the bulb. though rare, bulbs have been known to be the problem. If the bulb is breaking filiments ck the filiment orientation. filiments last longer in vertical orientation, where horizontal permits vibration to break the heated filiment when brake is applied.. good luck and let me know if This helped or not.

Posted on May 06, 2009

  • 4 Answers

SOURCE: 1997 Chevy Tahoe both turn signals stopped working

Sounds like the flasher unit to me. Normally the emergency flasher and turn signal are separate.

Posted on Jul 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Signal lights not working


In your "Control Panel," bring up mouse or pointing device properties. There should be a tab for your touch pad where you can enable and disable it.

Mar 19, 2014 | 1994 Chevrolet Beretta

1 Answer

1994 dodge dakota brake light ground location


The ground wiring on newer vehicles is a little complicated. Older cars, the ground would have been to the body around the tail-lights, but these have a ground wire in the harness and is connected to the turn-signal switch, and other sources. I don't think you have a ground problem. Does the fuse blow as soon as you press it into the fuse-block, or when you step on the brake? I believe you have a dead short somewhere, possibly a pinched turn-signal wire close to the tail-light assembly. Brake lights work through the turn-signal wires from the turn-signal switch on the steering column. That's how you can have one side blinking for turn while the other side stays on for brake. I'm kind of shooting in the dark here because I don't know what all you've done. If you replaced the turn-signal switch in the steering column, you may have pinched a wire or something there. Another thing, if the fuse doesn't blow as soon as you press it in, will both turn-signals work as long as you don't press on the brake? If you can provide a little more information, I might be able to help you more. One last thing....Have you replaced tail-light/turn-signal bulbs? If so, be sure you used the right bulb. You should only have two bulbs, one for back-up lights and one 1157-type combination for tail-lights and turn-signals. I have seen people use a single contact (1056) bulb in place of a 1157, which creates a short from brake/turn-signal back into the tail-light circuit. I do have a 1994 Dodge Dakota.

Mar 12, 2014 | 1994 Dodge Dakota Club Cab

1 Answer

My 1994 dodge dakota blows brake light fuse, replaced sw and still blows fuse after 2-3 times I push on pedal


You'll have to disconnect the lights to track down the short. It could be one of the lamp sockets, or something in the wiring, or in the turn signal switch.

Mar 05, 2014 | 1994 Dodge Dakota Club Cab

3 Answers

1994 Chevy C1500 truck. No rear brake lights


Most likely this is a brake light switch issue. Replace switch.

If your emergency flashers don't work, all flasher bulbs are fine, but flashing too fast, then check and replace Hazard light switch.

Oct 29, 2012 | 1994 Chevrolet C1500

1 Answer

Where do i find the turn signal flashers for a 1994 chevy beretta?


GM Corsica/Beretta 1988-1996 Repair Guide

The turn signal flasher is mounted in a clip on the right side of the steering column support bracket. The hazard flasher is located in the component center, under the instrument panel, on the right side. Replace the flasher by unplugging the old one and plugging in the new one.

Hope helped (remember rated this help) Good luck.

Oct 30, 2009 | Chevrolet Beretta Cars & Trucks

1 Answer

1994 Chevy truck. Turn signals do not work.


CHECK FUSE.IF GOOD YOU HAVE A BAD GROUND OR FAULTY TURN SIGNAL FLASHER.FLASHERS LOCATED ON THE INTERIOR FUSE RELAY BOX.

Sep 22, 2009 | Chevrolet 1500 Cars & Trucks

2 Answers

I can't find the fuse for the interior lights on my 1994 Caprice.


I have a 1994 chevy caprice classic LS. 4.3lLMy odometer meter works off and on...why does it do that? Sometimes I cans see how fast I'm going.. Other times the numberes don't light up. Same problem happen with my signal lights.. They both occur at the same time.. my signal light indicater and my MPH odometer.

Aug 15, 2009 | 1994 Chevrolet Caprice Classic

Not finding what you are looking for?
1994 Chevrolet Beretta Logo

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...