Question about 1994 Chevrolet S-10 Blazer

1 Answer

Spark plugs how to change the spark plugs on a 1994 chevy blazer and their location

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Chevrolet Master
  • 3,854 Answers

Your going to need a spark plug socket with a swivel, extension, and a spark plug wire pliers. You can access the spark plugs through the wheel well. you can from the top but that takes too long and you can't get to all of them from there. You can raise the front end just enough to give you some room in the wheel well with out removing the front wheels. To get to the spark plugs, move the wheel well splash guard up and out of the way so you can access the spark plugs on the side of the engine. One the passenger side is the easy one to work out and should take you under 20 min to do all three, change them one at a time so you don't mix the spark plug wires. On the drivers side is work on the #1plug (towards the front) and #5 (towards the fire wall) first and do #3 plug last. Spark plug #3 is behind the shock tower mount, you need to loosen it first with the socket, then remove the socket and remove and install the plugs by had. It should take you almost 10 min just to do that plug and a cramped hand.  When replacing the spark plugs, use anti seize so it's easier to remove the plugs next time and use platinum plugs so your good to go for 100,000 miles unless you have a plug failure due to running too lean or rich. Bring the truck down and place the ignition to the run position for 30 seconds and turn off for 10 seconds and then start and let idle for 1 min then go for a test drive to reset all the engine management sensors.  Good luck and hope this helps. Keep me posted, be glad to help.

Posted on Jun 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I was given a 1994 s10 Chevy Tahoe vortex blazer


I was given a 1994 s10 Chevy Tahoe vortex blazer??????? It's either a S-10 pick-up or it's a Tahoe or a Blazer not all three . So which is it ?

Mar 11, 2017 | 1994 Chevrolet S-10 Blazer

1 Answer

1992 chevy blazer 4.3 vortec engine 2w dr have change the fuel pump fuel filter spark plugs rotor in the distributing cap ignition coil.and still doesnt want to start only cranks but doesnt stay on.


Check the wireing to the pump they had problems with it it tended to over heat and corroad there is a service bulliton on the prroblem #25215705and a kit with new wires and connector to resist over heating Icould give you the kit # but i got a DELPHI pump and the connector dosn;t fit a chevy pump

Nov 23, 2010 | 1994 Chevrolet S-10 Blazer

2 Answers

Trying to locate the ignition module for chevy blazer s10 1994


Ignition module sits in the ignition distributor, remove distributor cap, there will be two elec. harness plugs, the one with two wire's is for the pick up coil, the other one is for the ignition module, just unscrew module out of distributor and install new one.

Sep 23, 2010 | 1994 Chevrolet S-10 Blazer

1 Answer

Spark plugs and wires for a 2000 chevy blazer


Hi,there is label number on spark plug wires.try to match the same number and replace one spark plug wire and one spark plug at the time!!!
good luck!!!!!!

Feb 21, 2010 | 2000 Chevrolet Blazer

2 Answers

Location of spark plugs on 4.3l v-6 in a 2001 chevy blazer


Chevy usually puts the spark plugs down below the exhaust manifold.
You usually have to do them by feel, or use a mirror.

Jan 02, 2010 | 2001 Chevrolet Blazer

1 Answer

I have a chevy s10 blazer that will not start it


If you have good pressure to fuel rail, then you may want to check the voltage coming to each injector with a voltmeter.
You may also want to check and make sure that every cylinder is getting spark.
If you are getting spark and fuel, then you may have a bad sensor somewhere but the car should be put on diagnostic scanner to pinpoint exact problem location.

Aug 25, 2009 | Chevrolet Blazer Cars & Trucks

1 Answer

1994 Chevy S 10 Blazer-no spark, new coil


Did you try the distributor? It could also be the ignitor chip.

Jun 19, 2009 | 1995 Chevrolet S-10 CA Edition

1 Answer

Cam shaft senor


It is part of the distributor according to a chevy forum I belong to

Oct 29, 2008 | 1996 Chevrolet Blazer

Not finding what you are looking for?
1994 Chevrolet S-10 Blazer Logo

209 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...