Question about 2004 Honda Accord

1 Answer

2004 accord engine rolls but wont start

Were is the crankshaft position sensor located

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 23 Answers

Usually behind the timing cover behind the crank

Posted on Apr 22, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 10 Answers

SOURCE: where is the o2 sensor located on a 1991 honda accord ex 2.2 engine

Further clarification on the O2 sensor location: It is in the exhaust pipe, under the center of the car, on top of the pipe, just aft of the oil filter.

Posted on Jul 14, 2008

emissionwiz
  • 74975 Answers

SOURCE: how change the cranfshaft sensor on honda accord 96 4 cilinder 2.2

It is attached to the engine oil pump houseing, one bolt I believe.

Posted on Oct 21, 2008

hi99ins
  • 123 Answers

SOURCE: SPEED SENSOR LOCATION FOR 1996 HONDA ACCORD

on the trans, its underneath the battery, in-line with the battery clamp toward the front of the car.

Posted on Jan 13, 2009

  • 9 Answers

SOURCE: 1990 honda accord lx not starting

I have had a similar problem with my honda. After doing some research, the distributors will fail and it is common. If you are able to replace the crank sensor that is great. you do not have to do the timing as long as you do not remove the whole distributor. I found it easier to remove and replace the whole distributor. remove the three screws and discconnect the connectors and pull it straight out. the installation is in reverse and the best thing is it will only go in one way. replace the screws and the connectors and your done. But you will have to do the timing. You might have to remove the spark plugs to see if they have fouled out. if they did see if you can clean them or replace.

Thanks
Good Luck

Posted on Jun 30, 2009

  • 491 Answers

SOURCE: Replace crankshaft position sensor

Remove the left front wheel....(drivers side). Remove all accessory belts. Remove the crankshaft shaft pulley.......remove the plastic lower timing belt cover.....and there it is! It is mounted with one bolt.
The wiring runs down the right side of the timing cover while looking at it from the drivers side of the car.

Posted on Aug 17, 2009

Testimonial: "I ended up having my mechanic do the work. He did say he had to move all those parts to get to the sensor. "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crankshaft position sensor located on the 2002 Mitsubishi Montero sport xls 3.5 truck.


Hi David, The link below is how to test the crank sensor (1997-2004 3.0l Montero, Hope this helps......CHEERS
http://easyautodiagnostics.com/mitsubishi/3.0L/crankshaft-position-sensor-test-1#3
The crankshaft position (CKP) sensor is located behind the timing belt... but testing it is done without removing the timing belt or its components. This is due to the fact that the crank sensor's connector is located on top of the engine and in plain view (next to the ignition control module). In the photo below, the orange arrow points to the location of the crankshaft position sensor connectors (photo applies to: 3.0L 1997-2004 Montero Sport).

Mar 31, 2016 | Mitsubishi Cars & Trucks

1 Answer

Where is the 2nd crank shaft sensor located, and is there a diagram to show where these sensors are located?


is it a no crank or crank no start?
Possible causes for code P0335
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery

Read more: http://engine-codes.com/p0335.html#ixzz3Cxw6SN6O

Sep 10, 2014 | 2004 Buick Rendezvous

1 Answer

Where is crankshaft position sensor located 1996 gmc sierra 1500


The crankshaft position sensor is located on the right-side (passenger side) of the engine. At the rear of the engine, behind the starter. You need to remove the starter to remove the crank sensor. Remember to disconnect the battery first. The starter can short against the cross member.

Mar 03, 2014 | Cars & Trucks

1 Answer

Were is the crank position sensor located on a 98 accord lx 2.2 motor?


There is no 2.2L motor in a 1998 Honda Accord.
The Crankshaft Position Sensor for the 2.3L 4-Cyl. engine is located behind the crankshaft pulley on the oil pump assembly.

May 10, 2011 | 1998 Honda Accord

1 Answer

Where is the idle sensor in the 2000 chevy impala


There is no idle sensor on the 2000 Chevrolet Impala, according to my online resource.

But, there is the following that senses rpm of the engine and thus the idle speed when the Throttle Position Sensor is at 5% or the accelerator pedal is not depressed:

Crankshaft Position Sensor Operation Engine speed is a very important input to the Powertrain Control Module (PCM). Crankshaft speed and position are the basis for many calculations made by the computer. Crankshaft position values are transmitted to the computer by pickup coils also known as Permanent Magnet (P/M) generators, Hall Effect sensors or optical sensors. The Crankshaft Position Sensor (CKP) also known as engine speed sensor is typically located in proximity to the crankshaft.
In addition, the PCM uses the CKP sensor in conjunction with the camshaft position sensor to calculate and perform misfire diagnostics.
Related Symptoms
  • A No Start / Intermittent Start condition - Can be caused by a faulty crankshaft position sensor due to loose connections, bad grounds, high resistance in the circuit, or opens in the circuit.
  • Engine Misfire Diagnostic Trouble Codes
NOTE: Engine Mechanical conditions can also create the same or similar symptoms. (Don't overlook basic mechanical integrity).
prev.gif next.gif

Nov 06, 2010 | 2000 Chevrolet Impala

2 Answers

Where is the crankshaft sensor located ?


The crankshaft position sensor (POS) is located on the oil pan facing the gear teeth (cogs) of the signal plate. It detects the fluctuation of the engine revolution.
After replacement, ECM reprogramming is required.
This vehicle may be subject to voluntary recall, CAMPAIGN I.D. # R0606, that involves the crankshaft position sensor:

Quote: Nissan has determined that on some 2003 - 2004 Altima and Sentra vehicles with the 2.5 liter engine the operation of the crank angle sensor is significantly affected by variations in temperature that occur due to the unique location of the sensor in the engine. Under certain driving conditions, these variations in temperature can be large enough to cause a brief interruption in the signal output from the sensor. If the interruption in the signal from the sensor is so brief that the Electronic Control Module (ECM) logic does not have time to diagnose the condition, the engine may stop running without warning while the vehicle is driven at low speed.

Jun 29, 2010 | 2004 Nissan Sentra

1 Answer

High idle stalls at lights code for crank sensor


Crankshaft and Camshaft Position Sensors Camshaft Position Sensor Engine timing is determined from the relationship between the crankshaft and camshaft. This relationship is maintained by a timing chain or timing belt. The Engine Management System does not control engine timing but it does monitor the relative position and speed of these shafts by monitoring signals generated by sensors. The Engine Management System (EMS) uses signals generated by the camshaft position sensor to synchronize fuel injection to the valve sequence and for the on-board diagnostic procedure for misfire detection. The EMS energizes the injector at or near the time the intake valve opens. For misfire diagnosis, the EMS compares the number of camshaft sensor reference pulses and the number of crankshaft position sensor reference pulses received. If the EMS receives an incorrect number of pulses Diagnostic Trouble Codes (DTC’s) should be stored in the EMS.
If the camshaft position sensor or circuit is faulty most engines will start. Some engine management systems will then default to a pre-programmed injector firing sequence. All injectors may be energized simultaneously or all of the injectors on one bank may be energized at the same time. If the CMP data is required for misfire detection and reliable CMP data is not present misfire detection would probably be suspended.
Related Symptoms The following symptoms can be caused by an intermittent wiring connection or faulty signal to the EMS:
  • Extended crank time with a cold engine
  • Intermittent rough running
  • Unstable idle
  • Bucking
  • Hesitation
  • Stumble
  • Chuggle
  • Poor fuel economy
  • Stalling on acceleration
Crankshaft Position Sensor Engine speed is a very important input to the Engine Management System (EMS). Crankshaft speed and position are the basis for many calculations made by the computer. Crankshaft position values are transmitted to the computer by pickup coils also known as Permanent Magnet (P/M) generators, hall-effect sensors or optical sensors. The Crankshaft Position Sensor (CKP) also known as engine speed sensor is located in close proximity to the crankshaft.
In addition the EMS uses minute variations in the CKP sensor data to determine engine misfire. The EMS uses this information in conjunction with the camshaft position sensor to perform misfire diagnostics.
Related Symptoms: No Start/Intermittent Start Condition – Can be caused by a faulty crankshaft position sensor due to loose connections, bad grounds, high resistance in the circuit, or opens in the circuit

Jun 23, 2009 | 2004 Nissan Altima

3 Answers

Crankshaft position sensor location on 2004 chrystler pacifica


can u please tell me where on my 2004 chrysler pacifica is the crankshaft sensor located?

May 02, 2009 | Chrysler Pacifica Cars & Trucks

1 Answer

Crankshaft Position Sensor location 04 PT Cruiser


It is located behind the **** of the starter on the front of the engine starting in '03 the 2.4 lt was changes the repair manual failed to update this..you may sneak it out with small fingers with out pulling out the starter.

7e1821a.jpg

Feb 08, 2009 | 2004 Chrysler PT Cruiser

Not finding what you are looking for?
2004 Honda Accord Logo

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...