Question about 2001 Volkswagen Jetta TDI

1 Answer

Test coil pack

No spark out of number 2 coil pack the other three have spark

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 128 Answers

You can test the pack. Not sure what the tolerances for this particular pack are, but the Primary should read in the .3-.9 ohm range and the secondary usually usually 1.0-9.0 ohms range. If you get some resistance at all, it is likely not bad. If there is zero resistance at either primary or secondary, it is probably bad and needs replacing,

Posted on Apr 22, 2014

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1986 Answers

SOURCE: No spark from coil pack

The most common reasons for them going out are not using dielectric grease properly when installing, and from washing your engine.

I believe this was a huge issue with Volkswagen vehicles

Posted on Aug 25, 2009

  • 1114 Answers

SOURCE: I have a 1999 VW Passat # 2 cylinder is not

Hello you will now need to disconnect the engines battery using the proper sized wrench or socket.Ounce you have disconnect the battery for a couple of minutes now reconnect the battery this should reboot the engines computer keep in mind just like at home on your PC when you install new hard wear you must restart or reboot your computer for the hard drive to recognize the updates and hard ware.

Posted on Jan 02, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Both coils do not fire on 1 and 4. Will start but only running on 2 cylinders. Could both coils be bad or should I look elsewhere?


Part 3 -How to Test the Ignition Module and Crank Sensor ...

easyautodiagnostics.com > Ford > 2.3L
Mar 1, 2012 - Spark plugs for cylinders #2 and #3 get spark at the exact same time. ...voltage -12 Volts) to both individual ignition coils within the coil pack. ... Ford Mustang or Ranger (or 2.3L Mazda B2300), this is what you'll need ... for this 'Switching Signal' at the coil pack... but you can also test this ... 1991, 1992, 1993.

How to Diagnose a Misfiring Cylinder (2.3L Ford Ranger ...

troubleshootmyvehicle.com > Ford > 2.3L
Apr 3, 2012 - Bad Fuel Injectors can cause a Misfire Condition. ... the ignition system on the 2.3L Ford Mustang or Ranger consists of 2 ignition coil packs, ...

2002 ranger misfire rough idle - Discussion on Topix

www.topix.com > Ford Ranger
Jul 27, 2007 - My truck is giving the code misfire in number 4 cyl. I replaced my spark plugs, Wires, Coil packs (both of them) and all my fuil ... three (3.0L v6) go bad, the fuel/air mixture gets messed up. Judged: 2. 2 ... My truck runs rough only at idle. ...code for ford ranger 2002, 2.3 5speed. truck runs like a champ but that ...

Extremely stumped! I need the best and brightest 1994 Ford ...

answers.edmunds.com > Edmunds Answers

Jan 31, 2016 | Cars & Trucks

1 Answer

2006 Suzuki forenza no fire from coil pack


what country? this is the WWW, post country for better answers.......!
Only a scope can see the fast 5mS signals to the coil.
so its either the coil pack or the ECU blown. (wires are always suspect)
you never said , all 4 are dead, or 1 or 2, and how many packs.
some non usa cars have wasted (2pak) spark , not 4 COPS.
state what cylinders have spark and which don't.
there are only 2 ways to fix cars.
1: guess and swap parts
2: use tools. my guess is you dont have them.
some coil packs are active (ignitor inside) others just a coil.
you can test the restance of the coils, with a DMM , ohm meter.
if active you cant.
the fsm covers this on all cars.
https://suzukipitstopplus.com/category/3-suzuki-service-manuals.aspx
the 2006 Forenza as delivered to USA has.....
has a large single, dual wasted spark coil pack. (brick)
it does in fact have , internal ignitor drivers. inside. so can not be tested
with and ohm meter on the primary side. but can be on the secondary
you do know how to test wasted spark , right, All spark plugs must be
attached and grounded for the coil to work,
1and 4 are shared.
2 and 3 are shared.
so to test , you must keep the spark plugs (both or all 4 is best)
attached and the shells of spark plugs grounded.
there is a fuse that powers the coil pack. (usa)
the fuel pump relay sends power to the coil pack.
so of that is dead,so will be the pack. (im reading FSM as it type)
get an FSM.
pin 2 on coil pack is power. 12v.
pin 1,is spark 1&4 drive (fast ECU pulse)
pin 3 is 2&3 coil drive. (scope can see it)

recap, are you using the correct wasted spark testing method.
and are all 4 spark plugs dead.?

Feb 18, 2013 | Suzuki Forenza Cars & Trucks

2 Answers

No spark at coil pack changed coil still no spark on 2 and 5


Try switching your coil packs around see if you can get spark out of the 2 & 5 with a different coil pack in that location. If that doesn't work maybe your ICM they can test the ICM at autozone, but can't test the coil packs.

May 03, 2011 | 1991 Buick Park Avenue

2 Answers

The problem in mine explorer is the cilinder number tree is not working can you tell me wy


Hello, here are 3 very common causes for that.
1. Bad spark plug.
2. bad spark plug wire.
3. Faulty fuel injector.

I hope this helps you.
Donnie

Mar 01, 2011 | 1999 Ford Explorer

1 Answer

Went through some water van died after sitting a day it started up but engine light is now on and sputters when stopped went to auto zone they say i have a 2 cylinder misfire what excactly does this mean...


It means that the number 2 cylinder (passenger front of the engine) is not working. Whether its spark, fuel, or mechanical. The first thing you can check is if there is spark to the cylinder. With the engine running remove the spark plug wire from the number 2 spark plug. Listen or look for spark out of the plug wire. If there isn't than you can check for spark out of the coil pack. Do this with a test light or spark tester. With the engine off remove the number 2 spark plug wire from the coil pack. With the spark tester installed or the test light hooked to ground and placed on the #2 coil post have some body crank the engine over. If ther4e is no spark that you might have a bad coil pack. If there is spark than possibly the plug wire is bad.

You should not drive it with a misfire as you could ruin the catalytic converter which is very expensive to replace.

Dec 01, 2010 | 2000 Dodge Caravan

1 Answer

Number one cyl on coil pack not firing, all others are, codes reads misfire on 1 cyl should i replace the coil pack and how do you test the pack


Check the spark plug first. then if the plug is good you wil need a digital ohm meter to test the coil pack. if you need to know how to remove the coil pack let me know, to test put on ohms should not have more than 2 1/2 ohms restance betweent coil lead to coil connector. If you test the coil pack on both sides of the pack and get a reading then the coil is bad, if it does not read then you haave a bad fireing plate diode.

Mar 12, 2010 | Ford Explorer Cars & Trucks

3 Answers

Ignition module where do I find it.


The ignition coils are mounted on it. Just follow the spark plug wires.

Nov 18, 2009 | 2005 Chevrolet Impala

1 Answer

Where does the firing order start on a 1991 3.8 buick lesabre. 165432


There are six VIN numbers of engines for the 1991 Buick Lesabre, with a 3.8 Liter engine.

1.Vin B
2.Vin 3
3.Vin C
4.Vin 1
5.Vin L
6.Vin K

All have the Firing Order of 1-6-5-4-3-2

For Vin B and 3:
Hood open, looking at the engine from the front of the car. The coil pack is behind the engine, close to the firewall. (Under the windshield)
The crankshaft pulley is down on the left side.

Spark plug numbering, for the spark plugs close to the radiator side.
From Left; (Front of engine), going Right-> 1-3-5
Spark plug numbering, for spark plugs on the backside of the engine.
From Left going Right-> 2-4-6

The distributorless coil pack sits on the backside of the engine, close to the firewall.
Numbering of where to put the spark plug wires;
There are three spark plug towers close to the engine. From Left to Right -> 3-5-7
There are three spark plug towers far from the engine. From Left to Right-> 6-4-2

For Vin C, 1, L and K:

Hood open, facing the car.
The Front of the engine faces to the Right. The crankshaft pulley is down, and to the Right.

Spark plugs close to the radiator;
From Left to Right-> 6-4-2
Spark plugs close to firewall, (Below windshield)
From Left to Right-> 5-3-1

The distributorless coil pack sits on the right side, in front of the engine. (The Front of the engine is on the right side. The crankshaft pulley is on the Right side)

Starting at the ->Back and coming Forward. (To the Front of the car)
On the Left side of the Distributorless Coil Pack, it is -> 4-2-6
On the Right side it is -> 1-5-3

Aug 19, 2009 | 1997 Buick Skylark

1 Answer

How do i plug in the spark plug coils? what order?


If it's the four cyl., the first coil pack bolts over the #2 spark plug. The #2 coil pack wire plugs into #3 spark plug. The number two coil pack bolts directly over the number four spark plug, and the #2 coil pack wire plugs into the #4 plug. The firing order is 1-4-2-3.

Jun 30, 2009 | 2000 Mazda Protege

1 Answer

CAR WONT CRANKS BUT WONT START


There is an easy way to determine wether your getting spark or not. Take a plug wire off a spark plug and put it next to a solid piece of metal like a bracket (somewhere you can see the end of the wire sparking) hold the wire behind the connection point, and crank the engine (have someone help). If you see a spark, you are getting spark to the plugs, but may still have a problem with the coil pack. There is only one way to find out. Take the coil pack off, and look at it. There are two types of coil packs - 1 piece and three piece (others may be possible) on a three piece, you will need to have each one tested to determine whether it's bad or not. On a one piece, pull it off and look at the glue like material underneath it, that part is called the modular (the coil pack(s) will screw down to it. The modular may be bad, and may be able to test it as well.

Apr 01, 2009 | 2000 Mitsubishi Eclipse

Not finding what you are looking for?
2001 Volkswagen Jetta TDI Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...