Question about 2006 Ford Explorer

Open Question

2013 ford explorer seat won't stow - 2006 Ford Explorer

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

dttech
  • 4803 Answers

SOURCE: 1997 Ford Explorer Power Seat Wiring

There are several options. It all depends on how bad you want the leather seats. You could disassemble the seats and transfer the upholstery from one seat to the other, or you could transfer the motor mechanisms from one seat to the other. The leather seats are most likely equipped with seat heater elements...there is no way you are going to get them to work without redesigning half of the vehicle, so you can either leave the heating elements out when you transfer the upholstery or just leave their respective connectors disconnected.

Posted on Nov 13, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I just purchased a 2005 cadilllac srx v8 n i cannot get the third row seat tto function? Help?


Rear Seat Switches
There are three push button switches that are used to operate the power folding seat; front stow switch, rear stow switch, and recline switch. The front stow switch is located in the right rear quarter trim panel just behind the second row seat. The rear stow and recline switches are located in the right rear trim panel just inside the liftgate. Battery positive voltage is supplied at all times to all three switches from the FFS SW Fuse located in the left rear fuse block. The folding seat will operate only in a supervised mode, i.e. press and hold the selected switch button through the entire cycle of operation, or release the switch when the desired seat position is reached. When any folding seat switch is pressed, it sends a 12 volt signal through the switch signal circuit to the RSM. The RSM then commands the appropriate seat motors to move in response to the switch signal.
Rear Seat Module and Power and Ground
The rear seat module controls the position of the third row seat. When commanded it moves the seat from the seated position to the stowed position, or, from the stowed position to the seated position. With the seat in the seated position, the RSM can also move the angle of the seat back forward or rearward.
Battery positive voltage is supplied at all times to the module through the battery positive voltage circuit and the FFSM fuse located in the left rear fuse block. This voltage is used to power up the RSM and also to apply power to the seat motors when commanded. The RSM is grounded through the module ground circuit and G401.
The first place to start would be check the fuse's .Do you know where the left rear fuse block is located ? Fuse Block - Left Rear
In the passenger compartment, near the left side of the rear seat under the carpet
If the fuse is good next thing to do would be ,have check for DTC'S in the rear seat module ! This has nothing to do with check engine light or OBD 2 diagnostic trouble codes an a code reader for said OBD2 codes will not work . Would need a factory scan tool to check these codes.
DTC B1395
Battery positive voltage is supplied at all times to the rear seat load floor switch and the rear seat position switch by the rear seat module (RSM). The RSM monitors these battery positive voltage supply circuits for the protection of internal circuitry of the module.
DTC B1395 Device Voltage Reference Output 1 Circuit
DTC B1420 Device Voltage
Battery positive voltage is supplied at all times to the seat adjuster switch and the memory seat module (MSM) through the same circuit. The MSM uses this battery voltage input to determine if battery positive voltage is applied to the seat adjuster switch.
DTC B1545 Seat Stow Switch 1 Circuit


?€¢
DTC B1546, Seat Stow Switch 2 Circuit


?€¢
DTC B3729 Seat Recline Control Switch


DTC B1735 Seat Front Up Switch Circuit


?€¢
DTC B1740 Seat Front Down Switch Circuit


?€¢
DTC B1745 Seat Rear Up Switch Circuit


?€¢
DTC B1750 Seat Rear Down Switch Circuit


?€¢
DTC B1755 Seat Assembly Horizontal Forward Switch Circuit


?€¢
DTC B1760 Seat Assembly Horizontal Rearward Switch Circuit


?€¢
DTC B1815 Seat Recline Forward Switch Circuit


?€¢
DTC B1820 Seat Recline Rearward Switch Circuit


Just from looking at the factory service info , I'd say you would be bet off just taking this to the dealer !
The first plase

May 28, 2016 | 2005 Cadillac SRX

1 Answer

Is there an auxillary plug under hood on 2013 ford explorer


The obvious question is "have you looked?". Secondly, check the vehicle handbook. After that, ask Ford customer support.

Jul 17, 2015 | 2013 Ford Explorer Limited

2 Answers

2013 Ford Explorer wipers won't shut off


Unfortunately, several cars made today are having these problems, and you have found one of them. Very likely you are in the market for a new wiper motor.
Be blessed.

Apr 13, 2015 | 2013 Ford - Explorer

1 Answer

My second row seat wont stow.


sounds like a cable has broke in the back of the seat or a a metal rod had come adrift or broke ,ask a local mechanic to have a look for you .

Mar 02, 2015 | 2011 Chrysler Town and Country

1 Answer

2013 Ford Explorer, Gas tank flap stuck shut. How do you open???


Lots of newer autos have a release by the drivers seat on the floor

Jan 11, 2015 | 2013 Ford Explorer Limited

1 Answer

I have 2013 Ford Explorer XL I want to know where


its either on the passagner side kick panel or on up by the truck arms are for lowering and raising the truck.. off on the side most of the time by the antenna.

Dec 16, 2014 | 2013 Ford - Explorer

1 Answer

How can stow n go seats be modified so seats are more level. Currently, my knees are too high.


thats the problem with this seating system , usually only meant for children to use , a gimmick by the manufacturer

Jul 20, 2014 | Chrysler Town & Country Cars & Trucks

1 Answer

Stow and go seat lock device broken


check for any recalls on the part first. the dealer may be your only option.

May 24, 2010 | 2005 Chrysler Town & Country

Not finding what you are looking for?
2006 Ford Explorer Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...