Question about 2008 Cadillac Cts

Open Question

Remove seat belt - 2008 Cadillac Cts

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i fix a jammed rear seat belt


You must remove the rear seat bottom and remove the bolt for the seat belt retractor, this will allow you to in jam the seat belt.

Dec 13, 2015 | Vauxhall Astra Cars & Trucks

1 Answer

How do you replace a seat belt?


Locate the area where the seat belt originates.

Remove the safety bolts located under the casing with a socket wrench. At the other end of the seat belt, remove the nut which holds it in place with a wrench.

Remove the shoulder harness of the seat belt with the wrench.Remove the bolt and nut which is attached to the anchor side of your old seat belt. This is at the bottom of the vehicle.Install the new anchor section of the seat belt.

http://www.xcardiag.com/

Jun 29, 2014 | 1984 Chevrolet Corvette

1 Answer

How to replace a seat belt


Remove b post trim to remove belt unit. Remove from seat. Fit is reverse.
Note...do not let belt over retract when fitting. Wedge it with summat

May 12, 2014 | 1998 Rover 200 Coupe

1 Answer

Unlock seat


If it's that tight it would be easier to remove the lower back seat and remove the 18 mm bolt and remove the seatbelt anchor. To remove the lower back seat pull up sharply on the front left and right sides of seat, only held in with plastic clips, then seat will pull forward and ouy

Mar 14, 2014 | Mercury Sable Cars & Trucks

1 Answer

How can i remove rear seats from my 2011 Vauxhall Insignia, also replace offside rear seat belt as I have had a mouse bite through the belt and the back seat


shoot the mouse !!!! ,,,, sorry coldnt resist ,,, you have to lift rear seatbase and boot carpet to get at the seat back bolts ,,, not a big problem ,,, the big one is getting at the seat belt because u have to remove alot of trim to get at the seat belt bolts ,,, alot of clips are involved that will break so source new clips before you start the job ,,,,rotten job so feel so sorry for you ,,,,

Dec 06, 2013 | 1992 Saturn SC

1 Answer

Remove seat belt


Hi Ray, Removal of the seat belts requires removal of the seats. Adjust the front seats to the fully backwards position and remove the fixing bolts and then unhook rails at the rear.You will notice a wire cable attached to each seat used to adjust the belt shoulder hight. This must also be disconnected. On later model vehicles there is an automatic retraction unit which pulls the driver and or passenger back into the seat in the event of the air bags being deployed. These connections must also be removed. If seats are electrically operated unplug all connectors. Remove seats and then gently remove plastic door pillar covers. (These are in two pieces for each front belt.) Removal will leave the fixing bolts of retractable part of the seat belt exposed. The buckle side is fixed with one bolt and has an electrical connection which must be disconnected. Hope this is of help? Regards John

Oct 27, 2013 | BMW Z4 Cars & Trucks

1 Answer

I need to replace a rear seat belt in a 1997 Ford Tarsus. Does any know the best way to access the assembly? In addition, are there any diagrams available that show the connection points?


please don't forget to rate, thx.

Retractor and Tongue—Sedan
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Safety Belt Bolt Bit T77L-2100A
NOTE: Safety Belt Bolt Bit T77L-2100-A should be used for safety belt removal and installation.

Removal
  1. Remove rear seat cushion. Refer to Section 01-10 .
Seat Cushion, Rear Sedan
Removal
  1. Apply knee pressure to lower front portion of the rear seat cushion. Push rearward to disengage rear seat cushion pad and frame (600A88) from rear seat cushion front retainers (63370).
  1. Remove rear seat cushion from vehicle.
  1. Remove rear seat back. Refer to Section 01-10 .
Seat Back, Rear 60/40 Split Bench—Sedan
Removal
  1. NOTE: Safety belt bolts do not secure seat back to vehicle.

    Remove rear seat cushion as described.
  1. Fold down back seat and remove two bolts in the center of each seat back striker plates.
  1. Remove two bolts from outboard rear seat back frame retaining brackets.
  1. Lift seat back up and pull forward to remove from vehicle.
  1. Remove panel (52018) and quarter trim panel (31012). Refer to Section 01-05 .
Trim Panel, Quarter—Sedan Removal
  1. Remove rear seat. Refer to Section 01-10 .
  1. Pull up on rear section of rear door scuff plate that overlaps lower quarter trim panel.
  1. Pull lower quarter trim panel away from body.
  1. Remove safety belt retaining bolt.
  1. Feed safety belt through lower quarter trim panel.
  1. Remove safety belt anchor plate-to-sill bolt from quarter panel.
  1. Remove retractor anchor nut and retractor from rear quarter panel.
  1. Remove upper seat belt anchor bolt and anchor from upper rear quarter panel.
  1. Slide anchor plate end of safety belt through the openings in the quarter trim panel.
  1. Remove outboard front safety belt retractor and tongue (611B08) from the vehicle.


    2a6fac0.gif


    Item Part Number Description 1 386277-S190 Bolt (Part of 611B68) 2 31012 Upper Rear Quarter Trim Panel 3 611B60 Retractor and Tongue 4 N800937-S190 Nut 5 389370-S190 Bolt 6 — Rear Quarter Panel (Part of Body) 7 52018 Lower Rear Quarter Trim Panel 8 — Mounting Stud (Part of Body)
  1. Remove seat belt anchor bolt and retractor and tongue from rear deck panel.


    fff90b0.gif

Installation
  1. To install, reverse Removal procedure.
  1. Make sure the safety belt webbing is not twisted. If it is, remove the twist.
  1. Tighten retractor anchor bolt and safety belt anchor plate-to-sill bolt to 34-46 Nm (25-33 lb-ft).
  1. Check the restraint system for proper operation.

Jun 30, 2009 | 1997 Ford Taurus

1 Answer

Seat Belt repair/replace


  1. Remove front seat.
  2. Remove adjuster cover. A
  3. Slide floor anchor cover.
  4. Remove floor anchor bolt. B
  5. Remove shoulder anchor bolt. C
  6. Remove front and rear kicking plate, then remove center pillar upper and lower garnish.
  7. Disconnect seat belt pre-tensioner connector.
  8. Remove the screw securing seat belt pre-tensioner retractor, then remove seat belt and seat belt pre-tensioner retractor.
  9. Remove bolts securing seat belt adjuster, then remove seat belt adjuster. Reverse procedure to install.J

Nov 03, 2008 | 2000 Nissan Maxima

1 Answer

Seat belt repair


first for the switch in window
the window switch is easy to test you just gotta remove switch out of the door leaving it hang there is a way to test with a guaged wire with fuse on it
take the main power wire and touch to the other connectors on the main switch if the window goes down or up the switch is the problem
im suggesting this way first with fuse cause its easier then testing the windows motor inside the door frame the switches should just pop out of the panel with out haveing to take panel off

now the seat belts there are 2 style that are common to chevy
one is inside the molding of the drivers panel you gotta pop off the panels easily and gently to get at the seat belt retractor this will be bolted to the metal under the molding

the other style is in the seat which you gotta unbolt the seat under the top half it will need to be unbolted at the bottom top half of seat
when you pull threw the top section of top half of seat remember to tie a string to the end so that when you pull threw top half the string will be there so you can connect too new belt and pull back threw with ease make the string long enough to hang

now the bottom half of seat what i call the "**** seat" you remove the molding at bottom around the belt retractor this will be bolted to floor bolt also pull belt threw molding once molding removed
disconnect any electric wires

now saftey issue involved with seat belt removal is for a reason i dont know of the dealer ship always discharges the belts and air bags once removed i guess because of static electricity becareful when you remove belt and replacing belts cause static elec. can set them off
once your seat belt is removed place in card board box and take to dealer after complition of installing new belt they will discharge your seat belt for you and then you can dispose of it properly

May 29, 2008 | 2000 Chevrolet Suburban

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...