Question about 1989 Dodge Dakota 2WD

1 Answer

Wheel hub assembly diagram

Diagram of front wheel assembly

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Go to you tube and ask for "How to replace Dodge Dakota front hub", you will find 2 or 3 good videos about it, I follow these videos and change mine in about 3 hours, note that I never did it in any car or truck. Another tip is that all videos I found was about 4x4 Dakotas and mine is 4x2, the only difference is the hub center fix, 28 mm screw on 4x2 and 32 mm nut on 4x4.

Posted on Aug 15, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
slazabaza
  • 47 Answers

SOURCE: front wheel hub assembly replacement

if you have basic knowledge you should be able to carry out this job yourself. you will probably need to ring a dealership and ask very kindly if you could have the torque settings for the nuts and bolts ect.

hope this helps.

Posted on Mar 18, 2009

  • 101 Answers

SOURCE: replacing front wheel hub assembly 1996 Dodge caravan

first jack up the van remove the wheel remove the brake caliper and rotor remove the axel nut then remove the three bolts on the back of the hub tap on the hub with a hammer it should come out hope this is helpful

Posted on Mar 19, 2009

  • 66 Answers

SOURCE: i need a diagram on front hub and brake assembly

8–Stud Rotor

  1. Raise and support the vehicle.
  2. Remove the wheel.
  3. Remove the hub extension.
  4. Remove the brake caliper assembly.
  5. Remove the axle nut cotter pin. Remove the axle nut.
  6. Disconnect the ABS wheel speed sensor wire from under the hood. Remove the sensor wire from the frame and steering knuckle, if equipped.
  7. Back off the hub/bearing mounting bolts 1/4 inch each. Then tap the bolts with a hammer to loosen the hub/bearing mounting bolts.
  8. Remove the bolts and remove the hub/bearing assembly.

Posted on Sep 16, 2009

techbuster
  • 5081 Answers

SOURCE: 2001 ram 2500 how to remove the wheel hub assembly

Remove tire. Remove caliper and caliper holder. Remove rotor. Using a 36 MM socket remove center nut and slide hub off spindle. If hub does not come off freely use wheel puller to remove hub.Loosen front wheel lug nuts. Jack up and support front of truck with jack stands ( put them in the middle so both you can get to both sides of the truck). Remove tire, Remove caliper and caliper holder. romove rotor ( I had to use a 2x4 wedged between rotor and lower controll arm rubber stoper. then started truck and turned the wheel right or left to pop rotor free). remove 3 bolts that hold hub to knuckle. on the next step I used a steel pipe about 1 1/2 foot i think about 2 inches in diamater. wedge it between lower controll arm rubber stoper. then start truck turn the wheel left or right to let power steering pump do the work. It poped it off easy for me both sides in less than 1 hour. put alot of anti seize on the new hubs and bolts in case you have to replace them again. use a torque wrench to tighten all bolts. Great time to replace brakes as long as you are in the area. hope this helps.

Posted on Oct 11, 2009

  • 64 Answers

SOURCE: Four wheel drive wont engage. Tranfer case is

Sounds like you either have a vaccum leak or your 4 wheel drive actuator is not working to engage the front differential.On my 98 ram there is a black and red plastic lines that are used for the vaccum lines. They are underneath and go from the transfer case to the front axle, check to see if one or both might be cracked or broke completely.If the lines are good then it could be your actuator on the front axle. A new one is about $93 at advance auto parts and not very hard to replace

Posted on Dec 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We need a picture of a Front wheel bearing hub assembly or diagram


DUDE, GO TO AUTOZONE.....GET THE SHOP MANUAL...BUY IT, LOOK AT IT.....OR HAVE THE AUTOZONE PEOPLE PRINT YOU A DIAGRAM OF THE FRONT HUB ASSY.

Jul 29, 2014 | 1996 Ford F150 Regular Cab

1 Answer

Does anyone know where i can get a diagram of a the front right wheel hub assembly for a 2 wheel drive dodge dakota 3.9 liter engine yes it has abs to?


Check the left side hub and you will need the same set up. The only difference between left and right hubs will be left and right hand threads of the wheel nuts

Mar 02, 2013 | Dodge Dakota Cars & Trucks

1 Answer

Front wheel assembly diagram


For front wheel assembly diagram and replacement,click the link below and go through procedure:----Front wheel hub assembly Diagram and replacing procedure? http://howtobyme.blogspot.in/2012/02/front-wheel-hub-assembly-diagram-and.html
----------Front wheel assembly diagram to replace wheel bearing? http://howtobyme.blogspot.in/2012/02/front-wheel-assembly-diagram-to-replace.html
-------------How to replace Front wheel bearing? http://howtobyme.blogspot.in/2012/02/how-to-replace-front-wheel-bearing.html
-----------Check all 3 links one by one.This will help.Thanks.

Feb 22, 2012 | Ford F-250 Cars & Trucks

1 Answer

2004 F-150 4X4 XLT EXT CAB 5.4L NEED FRONT WHEEL HUB ASSEMBLY DIAGRAM


  1. n0051415.gif
  1. Item
Part Number Description 1 W706540-S900 Axle-to-wheel hub nut (4x4 only)
Removal Note 2 - Wheel speed sensor harness connector
Removal Note 3 2027 Anchor plate bolt (2 required) 4 - Brake caliper, pads and anchor plate
Removal Note 5 1125 Brake disc 6 1107 Wheel hub-to-wheel knuckle bolts 7 1104 Wheel bearing and hub assembly
Removal Note 8 N642567-S36 Tie-rod end-to-wheel knuckle nut 9 W707254-S427 Lower ball joint-to-wheel knuckle nut 10 W520215-S427 Upper ball joint-to-wheel knuckle nut 11 3K185 Wheel knuckle
Installation Note 12 W710279 Integrated wheel and bolt (3 required)


Mar 07, 2011 | 2004 Ford F150

1 Answer

Left front wheel bearing replacement diagram


Removal & Installation Front To Remove:
The front wheel bearings are not serviced separately. If the front wheel bearings are defective, the hub and bearing assembly must be replaced.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Lubricate the threads on the halfshaft with clean engine oil.
  3. Remove or disconnect the following:
    • Front wheels
    • Halfshaft hub nut
    • Caliper from the steering knuckle WARNING
      DO NOT allow the brake hose to support the weight of the caliper.
    • Brake rotor
    • Anti-lock Brake System (ABS) sensor from the backing plate
    • Hub and bearing assembly from the backing plate
    • Hub and bearing assembly from the halfshaft
    • Hub and bearing assembly
To Install:
Exploded view of the front hub mounting and related components 7922xg36.gif

  1. Install or connect the following:
    • Hub and bearing assembly onto the halfshaft
    • Hub and bearing assembly to the backing plate. Torque the 3 bolts alternately and evenly to 70 ft. lbs. (95 Nm).
    • ABS sensor
    • Brake rotor
    • Caliper on the steering knuckle.
    • Halfshaft nut. Torque it to 118 ft. lbs. (160 Nm).
    • Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).

Oct 18, 2010 | 2001 Oldsmobile Aurora

1 Answer

How do you remove the front wheel hub?


Hope this diagram helps:

Exploded view of the steering knuckle and hub assembly


f891ebe.gif

May 04, 2010 | 1995 Nissan Maxima

1 Answer

Need diagram for replacing front hub assembly on


to get the cv joint axle off on the 98 corolla, you have to remove the wheel, shock/strut, and control arm, pop it out of the transmission, and replace, i think there is a cover that you might have to take off first before you get to the cv, its been about 6 months since i replaced mine, sorry... but good luck and god bless, Please Rate me!

Nov 08, 2009 | 1998 Toyota Corolla

1 Answer

I need a diagram on front hub and brake assembly for 1999 dodge 1 ton dually 2 wheel drive. the front brake rotor is warped i need to replace it


8–Stud Rotor
  1. Raise and support the vehicle.
  2. Remove the wheel.
  3. Remove the hub extension.
  4. Remove the brake caliper assembly.
  5. Remove the axle nut cotter pin. Remove the axle nut.
  6. Disconnect the ABS wheel speed sensor wire from under the hood. Remove the sensor wire from the frame and steering knuckle, if equipped.
  7. Back off the hub/bearing mounting bolts 1/4 inch each. Then tap the bolts with a hammer to loosen the hub/bearing mounting bolts.
  8. Remove the bolts and remove the hub/bearing assembly.

Sep 16, 2009 | 2000 Dodge Ram 3500

1 Answer

1986 K5 Blazer front hub/axle problem


3 bolts from the back, axle nut and take the caliper off pretty easy.

Jan 20, 2009 | 1986 Chevrolet S-10 Blazer

Not finding what you are looking for?
Cars & Trucks Logo

233 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...