Question about 2003 GMC Envoy

Open Question

MY 2003 GMC ENVOY SKIPS AND SHAKE

SKIP,SHAKE,RIDES ROUGH

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 4 Answers

SOURCE: How to replace the headlights on my 2003 GMC envoy.

The headlights on the envoy are the easiest parts of the car to repair. You just pull the two tabs at the top of the headlights, screw out the bulb containers and you are good to go

Posted on Nov 15, 2008

Ad
  • 1 Answer

SOURCE: 2003 GMC Envoy lower 3 heater fan settings quit working.

had same problem on my XUV. changed the blower motor resistor, located under passenger side dash. easy to change, works no problem.

Posted on Feb 17, 2009

  • 179 Answers

SOURCE: 2003 GMC Envoy stalling w/ AC on when stopping

try turning up the idle ajustment screw also have alternator checked, another solution would be to have your car tuned up weak spark from your coil worn plugs wires etc. not enough power is being produced

Posted on May 31, 2009

  • 691 Answers

SOURCE: how do you change brakes on a 2003 gmc envoy

don't need any special tools, standard sockets sets, "C" clams is a must unless your a He-Man and wrench set, plyer or needle nose will do. I assumed being 2003 your rotor never have been turn and i recommend every time you change your bakes is good idea to have your rotor turn. reason is it will make your pad last lot longer, removed any vibration and better even wear on the pad and eliminate any squealing although is not necessary to do so. make sure you get extra break fluid to bleed the brakes. get your self 5 feet long smallest vacum rubber hoses and a glass jar to bleed your brake fluid in. the rubber vacum hose you going to use to fit on to the bleeding nipple and run the other end of line to your the glass jar to save the brake fluid when you bleed the brakes. when removing caliper, check inspect make sure the rubber seals around your piston look good and not crack or deteriorated. before applying new pad make sure you open the bleed valve to reduce the pressure by turning the bleed nipple counter clockwise and leave it open attach that rubber hoses to the nipple because you going to press on the piston back into it housing with the "C" clamp in order for new pad to fit. becareful not to damage the rubber seals around the piston. its going to take lots of effort to push that piston back in so be a bare with it if needs to. once the pad is back in make sure you keep the reservoir full with brake fluid and then bleed the brake. two people is a good idea to do brake. one will do the pumping the brake and holding it down and other will bleed the nipple. I bleed it 2-3 time will do the job. good luck!

Posted on Jul 17, 2009

johnjohn2
  • 5763 Answers

SOURCE: where is coolant temp sensor located on 2003 gmc

heres a diagram to show you where the coolant temp sensor is located, its behind the alternator on the left side (driverside),the sensor just unplug the connector and then unscrew it and out it comes.

Posted on Jun 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 envoy smells like fumes and idles rough


have you checked for a vacuum leak?pcv attached,no leaks around plenum,engine coolant temp sensor reading right.

May 31, 2012 | 2003 GMC Envoy Xl

1 Answer

My Envoy will not stay in two-wheel drive mode (it shifts to neutral while I'm driving). When I use AWD, it rides very rough, particularly during tight turns. cjccbay1@msn.com


check tires are matching and air level correct but sounds like problem in drive train possible problem with a bad front c-v joint/ trans-axle or fault with actuator at trans check wiring and actuator mounting

May 06, 2010 | 2002 GMC Envoy

1 Answer

My 2003 GMC Envoy XL's check engine light is on and idles rough. I suspect an O2 sensor and was wondering if a person can buy an analyzer to heck it themselves instead of paying a mechanic? Richard


You can take your vehicle to a place like Auto Zone, they can read the fault code with scanner, or you can buy a OBD II scanner for anywhere between $50 to $100. Interpreting the codes may require some knowledge of the car though.

Apr 18, 2010 | 2003 GMC Envoy Xl

2 Answers

2004 envoy 4.2 6cyl. runs rough. had a new


take the breather off and take a 10 mm socket to take the coil off easy to get to then take a 5/8 plug socket to take out plugs easy to get to,

Jan 03, 2010 | 2003 GMC Envoy Xl

Not finding what you are looking for?
2003 GMC Envoy Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...