Question about 2001 Peugeot 206 1.6

1 Answer

Exhaust manifold How do I remove lower bolts on exhaust manifold. Got top four off with ease but can't access lower bolts

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 201 Answers

Reach from under the car after exhaust pipe is removed from manifold.

Posted on Jun 13, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to remove the exhaust manifold on the right side of a 94 4.9l engine in a cadillac deville. It has a broken bolt in the exhaust. What is involved in removing the manifold?


I suggest you use all new exhaust manifold hardware and torque new bolts to 20 Ft Lbs.
4.5L and 4.9L Engines
RIGHT
Disconnect the negative battery cable. Remove the air cleaner. Remove the exhaust crossover pipe. Disconnect the oxygen and coolant temperature sensors. Remove the catalytic converter-to-AIR pipe clip bolt. Remove the upper manifold-to-cylinder head bolts. Raise and safely support the vehicle. Disconnect the converter air pipe bracket from the stud and remove the converter-to-manifold exhaust pipe. Support the engine cradle with screw jacks and remove the rear cradle bolts. Loosen the front cradle bolts and slightly lower the Engine cradle. Remove the remaining exhaust manifold-to-cylinder head bolts, the AIR pipe, and the manifold. Clean the gasket mounting surfaces.
To install:
Install the exhaust manifold and replace the AIR pipe. Tighten the manifold mounting bolts to 16-18 ft. lbs. (21-24 Nm). Install the manifold-to-converter exhaust pipe and replace the converter air pipe bracket to the stud. Raise the Engine cradle and install the rear cradle bolts. Tighten to 75 ft. lbs. (102 Nm). Lower the vehicle. Replace the upper manifold-to-cylinder head bolts. Replace the converter air pipe to AIR pipe clip bolt. Connect the coolant temperature and oxygen sensor connectors. Replace the exhaust crossover pipe. Replace the air cleaner and connect the negative battery cable. Start the Engine and check for leaks.

Mar 28, 2017 | Cadillac Cars & Trucks

1 Answer

How to replace water pump on 1991 pontiac quad 4


2.3L Engine
  1. Disconnect the negative battery cable
  2. Detach the oxygen sensor connector.
  3. Properly drain the engine coolant into a suitable container. Remove the heater hose from the thermostat housing for more complete coolant drain.
  4. Remove upper and lower exhaust manifold heat shields.
  5. Remove the bolt that attaches the exhaust manifold brace to the manifold.
  6. Break loose the manifold to exhaust pipe spring loaded bolts using a 13mm box wrench.
  7. Raise and safely support the vehicle. NOTE: It is necessary to relieve the spring pressure from 1 bolt prior to removing the second bolt. If the spring pressure is not relieved, it will cause the exhaust pipe to twist and bind up the bolt as it is removed.
  8. Remove the manifold to exhaust pipe bolts from the exhaust pipe flange as follows:
    1. Unscrew either bolt clockwise 4 turns.
    2. Remove the other bolt.
    3. Remove the first bolt.
  9. Pull down and back on the exhaust pipe to disengage it from the exhaust manifold bolts.
  10. Remove the radiator outlet pipe from the oil pan and transaxle. If equipped with a manual transaxle, remove the exhaust manifold brace. Leave the lower radiator hose attached and pull down on the outlet pipe to remove it from the water pump.
  11. Carefully lower the vehicle.
  12. Remove the exhaust manifold, seals and gaskets.
  13. Loosen and reposition the rear engine mount and bracket for clearance, as required.
  14. Remove the water pump mounting bolts and nuts. Remove the water pump and cover assembly, then separate the two pieces.

Feb 23, 2012 | 1991 Pontiac Grand Am

1 Answer

Diragram on how to change the water pump on a 1995 z24 cavalier 2.3


Check this procedure, according with the repair guide for...

2.3L and 2.4L Engines
(see Figure 9)
  1. Disconnect the negative battery cable
  2. Detach the oxygen sensor connector.
  3. Properly drain the engine coolant into a suitable container. Remove the heater hose from the thermostat housing for more complete coolant drain.
  4. Remove upper exhaust manifold heat shield.
  5. Remove the bolt that attaches the exhaust manifold brace to the manifold.
  6. Remove the lower exhaust manifold heat shield.
  7. Break loose the manifold to exhaust pipe spring loaded bolts using a 13mm box wrench.
  8. Raise and safely support the vehicle.
It is necessary to relieve the spring pressure from 1 bolt prior to removing the second bolt. If the spring pressure is not relieved, it will cause the exhaust pipe to twist and bind up the bolt as it is removed.
  1. Unfasten the two radiator outlet pipe-to-water pump cover bolts.
  2. Remove the manifold to exhaust pipe bolts from the exhaust pipe flange as follows:
    1. Unscrew either bolt clockwise 4 turns.
    2. Remove the other bolt.
    3. Remove the first bolt.
On the 2.4L engines, DO NOT rotate the flex coupling more than 4° or damage may occur.Pull down and back on the exhaust pipe to disengage it from the exhaust manifold bolts.
  1. Remove the radiator outlet pipe from the oil pan and transaxle. If equipped with a manual transaxle, remove the exhaust manifold brace. Leave the lower radiator hose attached and pull down on the outlet pipe to remove it from the water pump. Leave the radiator outlet pipe hang.
  2. Carefully lower the vehicle.
  3. Unfasten the exhaust manifold-to-cylinder head retaining nuts, then remove the exhaust manifold, seals and gaskets.
  4. For the 2.4L engine, remove the front timing chain cover and the chain tensioner. For details, please refer to the procedure located later in this section.
  5. Unfasten the water pump-to-cylinder block bolts. Remove the water pump-to-timing chain housing nuts. Remove the water pump and cover mounting bolts and nuts. Remove the water pump and cover as an assembly, then separate the two pieces.

zjlimited_2033.jpg

Fig. 9: Water pump and cover mounting - 2.3L and 2.4L engines (click over image for zoom)

To install:

  1. Thoroughly clean and dry all mounting surfaces, bolts and bolt holes. Using a new gasket, install the water pump to the cover and tighten the bolts finger-tight.
  2. Lubricate the splines of the water pump with clean grease and install the assembly to the engine using new gaskets. Install the mounting bolts and nuts finger-tight.
  3. Lubricate the radiator outlet pipe O-ring with antifreeze and slid the pipe onto the water pump cover. Install the bolts finger-tight.
  4. With all gaps closed, tighten the bolts, in the following sequence, to the proper values:
    1. Pump assembly-to-chain housing nuts-19 ft. lbs. (26 Nm).
    2. Pump cover-to-pump assembly-106 inch lbs. (12 Nm).
    3. Cover-to-block, bottom bolt first-19 ft. lbs. (26 Nm).
    4. Radiator outlet pipe assembly-to-pump cover-125 inch lbs. (14 Nm).
  5. Using new gaskets, install the exhaust manifold. Make sure to following the tightening sequence and torque specifications given in the exhaust manifold procedure located in this section.
  6. Raise and safely support the vehicle.
  7. Index the exhaust manifold bolts into the exhaust pipe flange.
  8. Connect the exhaust pipe to the manifold. Install the exhaust pipe flange bolts evenly and gradually to avoid binding. Turn the bolts in until fully seated.
  9. Connect the radiator outlet pipe to the transaxle and oil pan. Install the exhaust manifold brace, if removed.
  10. On the 2.4L engine, install the timing chain tensioner and front cover.
  11. Install the lower heat shield.
  12. Carefully lower the vehicle.
  13. Fasten the bolt that attaches the exhaust manifold brace to the manifold.
  14. Tighten the manifold-to-exhaust pipe nuts to specification.
  15. Install the upper heat shield.
  16. Attach the oxygen sensor connector.
  17. Fill the radiator with coolant until it comes out the heater hose outlet at the thermostat housing. Then connect the heater hose. Leave the radiator cap off.
  18. Connect the negative battery cable, then start the engine. Run the vehicle until the thermostat opens, fill the radiator and recovery tank to their proper levels, then turn the engine off.
  19. Once the vehicle has cooled, recheck the coolant level.

Hope helps; remember to rating this answer and leave a testimonial comment. Thank you for using FixYa.

Oct 13, 2011 | 1995 Chevrolet Cavalier

1 Answer

What are the torque specs for 1996 Buick Century 3.1 L intake manifold?


Front Pipe REMOVAL & INSTALLATION Pipe Without Catalytic Converter
  1. Before removing any component of the exhaust system, always squirt a liquid rust dissolving agent onto the fasteners for ease of removal..
  2. Raise and support the front of the vehicle on jackstands.
  3. Remove the exhaust pipe-to-manifold nuts.
  4. Support the catalytic converter, then disconnect the pipe from the converter. Remove the pipe.
  5. Remove the exhaust gaskets. To install:
  6. Be sure to use all new gaskets when required. Assemble the system, check the clearance and tighten the bolts to about 15-30 ft. lbs. (20-41 Nm). Fig. 1: Front exhaust pipe connection common on vehicles with the catalytic converter not included 86813320.gif

  7. All clamps should be tightened to about 18-25 ft. lbs. (24-34 Nm). Do overtighten the clamps. If pipes become dented they can leak.
Pipe With Catalytic Converter
  1. Before removing any component of the exhaust system, always squirt a liquid rust dissolving agent onto the fasteners for ease of removal.
  2. Raise and support the vehicle.
  3. On some vehicles you will need to remove the brace from the transaxle.
  4. Remove the exhaust pipe nuts from the manifold.
  5. Support the catalytic converter pipe bolts from the rear of the converter.
  6. Lower the catalytic converter/front pipe assembly from the vehicle. To install:
  7. Be sure to use all new gaskets when required.
  8. Attach the new catalytic converter/front pipe assembly to the vehicle. Tighten the pipe to manifold nuts to 20-40 ft. lbs. (27-55 Nm).
  9. Attach the bolts at the rear of the catalytic converter/front pipe. Tighten them to 30-35 ft. lbs. (41-47 Nm).
  10. Connect the brace at the transaxle if removed.
  11. Lower the vehicle. prev.gif next.gif

Dec 18, 2010 | Buick Century Cars & Trucks

2 Answers

How to replace water pump on 97 pontiac sunfire 2.4


PLEASE DON'T FORGET TO RATE! THANKS! 2.3L & 2.4L Engines
  1. Disconnect the negative battery cable
  2. Detach the oxygen sensor connector.
  3. Properly drain the engine coolant into a suitable container. Remove the heater hose from the thermostat housing for more complete coolant drain.
  4. Remove upper exhaust manifold heat shield.
  5. Remove the bolt that attaches the exhaust manifold brace to the manifold.
  6. Remove the lower exhaust manifold heat shield.
  7. Break loose the manifold to exhaust pipe spring loaded bolts using a 13mm box wrench.
  8. Raise and safely support the vehicle.
It is necessary to relieve the spring pressure from 1 bolt prior to removing the second bolt. If the spring pressure is not relieved, it will cause the exhaust pipe to twist and bind up the bolt as it is removed.
  1. Unfasten the two radiator outlet pipe-to-water pump cover bolts.
  2. Remove the manifold to exhaust pipe bolts from the exhaust pipe flange as follows:
    1. Unscrew either bolt clockwise 4 turns.
    2. Remove the other bolt.
    3. Remove the first bolt.
On the 2.4L engines, DO NOT rotate the flex coupling more than 4° or damage may occur.
  1. Pull down and back on the exhaust pipe to disengage it from the exhaust manifold bolts.
  2. Remove the radiator outlet pipe from the oil pan and transaxle. If equipped with a manual transaxle, remove the exhaust manifold brace. Leave the lower radiator hose attached and pull down on the outlet pipe to remove it from the water pump. Leave the radiator outlet pipe hang.
  3. Carefully lower the vehicle.
  4. Unfasten the exhaust manifold-to-cylinder head retaining nuts, then remove the exhaust manifold, seals and gaskets.
  5. For the 2.4L engine, remove the front timing chain cover and the chain tensioner. For details, please refer to the procedure located later in this section.
  6. Unfasten the water pump-to-cylinder block bolts. Remove the water pump-to-timing chain housing nuts. Remove the water pump and cover mounting bolts and nuts. Remove the water pump and cover as an assembly, then separate the two pieces.

01add58.gif
Water pump and cover mounting-2.3L and 2.4L engines

To install:
  1. Thoroughly clean and dry all mounting surfaces, bolts and bolt holes. Using a new gasket, install the water pump to the cover and tighten the bolts finger-tight.
  2. Lubricate the splines of the water pump with clean grease and install the assembly to the engine using new gaskets. Install the mounting bolts and nuts finger-tight.
  3. Lubricate the radiator outlet pipe O-ring with antifreeze and slid the pipe onto the water pump cover. Install the bolts finger-tight.
  4. With all gaps closed, tighten the bolts, in the following sequence, to the proper values:
    1. Pump assembly-to-chain housing nuts-19 ft. lbs. (26 Nm).
    2. Pump cover-to-pump assembly-106 inch lbs. (12 Nm).
    3. Cover-to-block, bottom bolt first-19 ft. lbs. (26 Nm).
    4. Radiator outlet pipe assembly-to-pump cover-125 inch lbs. (14 Nm).
  5. Using new gaskets, install the exhaust manifold. Make sure to following the tightening sequence and torque specifications given in the exhaust manifold procedure located in this section.
  6. Raise and safely support the vehicle.
  7. Index the exhaust manifold bolts into the exhaust pipe flange.
  8. Connect the exhaust pipe to the manifold. Install the exhaust pipe flange bolts evenly and gradually to avoid binding. Turn the bolts in until fully seated.
  9. Connect the radiator outlet pipe to the transaxle and oil pan. Install the exhaust manifold brace, if removed.
  10. On the 2.4L engine, install the timing chain tensioner and front cover.
  11. Install the lower heat shield.
  12. Carefully lower the vehicle.
  13. Fasten the bolt that attaches the exhaust manifold brace to the manifold.
  14. Tighten the manifold-to-exhaust pipe nuts to specification.
  15. Install the upper heat shield.
  16. Attach the oxygen sensor connector.
  17. Fill the radiator with coolant until it comes out the heater hose outlet at the thermostat housing. Then connect the heater hose. Leave the radiator cap off.
  18. Connect the negative battery cable, then start the engine. Run the vehicle until the thermostat opens, fill the radiator and recovery tank to their proper levels, then turn the engine off.
  19. Once the vehicle has cooled, recheck the coolant level.

Sep 13, 2010 | Pontiac Sunfire Cars & Trucks

1 Answer

Where are the exhaust system bolts located?


Removal & Installation 2.2L Engine To Remove:
  1. Remove or disconnect the following:
    • Negative battery cable.
    • Heat shield.
    • Oxygen sensor.
  2. Raise and safely support the vehicle.
  3. Remove exhaust pipe from the exhaust manifold.
  4. Lower the vehicle.
  5. Remove the exhaust manifold mounting nuts from the cylinder head. chevy_cav_02-04_exmanifold.gif

  6. Remove the exhaust manifold.
  7. Clean the mating surfaces.
  8. Check for cracks, broken flanges and gasket surface damage.
  9. Use a straight edge and a feeler gauge. If the flanges or the mating surfaces do not align, the manifold is warped and should be replaced.
To Install:
NOTE: The manufacturer recommends using new exhaust system nuts.
  1. Install the manifold gasket.
  2. Position the exhaust manifold to the cylinder head. Exhaust manifold 2.2L 87953055.gif

  3. Install the new exhaust manifold nuts. Tighten the nuts starting from the center and working toward the ends to 110 in lbs (12.5 Nm).
  4. Raise and safely support the vehicle.
  5. Install the exhaust pipe to the manifold using a new flex coupler gasket.
  6. Install new exhaust flange mounting nuts.
    • Tighten to 33 ft lbs (45 Nm).
  7. Lower the vehicle.
  8. Install the oxygen sensor.
  9. Install the heat shield.
  10. Connect the negative battery cable.
2.4L Engine To Remove:
  1. Disconnect the negative battery cable
  2. Disconnect the Oxygen (O2) sensor electrical connector.
  3. Remove the (O2) sensor.
  4. Raise and safely support the vehicle. Exhaust brace 2.4L 87953053.gif

  5. Remove the exhaust manifold brace-to-manifold bolt and the oil pan nuts, if necessary. Exhaust heat shield 2.4L 87953051.gif

  6. Remove the upper heat shield. NOTE: Do NOT bend the exhaust flex decoupler more than necessary to remove it. Excessive movement will damage the flex decoupler
    Exhaust flex decoupler 87953056.gif

  7. Remove the manifold-to-exhaust flex decoupler fasteners.
  8. Remove the exhaust pipe.
  9. Carefully lower the vehicle.
  10. Remove the exhaust manifold-to-cylinder head mounting nuts/bolts. Remove the exhaust manifold.
  11. Discard the gaskets and/or seals. Clean the mating surfaces.
To Install:
Exhaust manifold 2.4L 87953055.gif

  1. Install new exhaust manifold gaskets. Position the exhaust manifold on the cylinder head. Tighten the mounting bolts in sequence to 110 in lbs (12.5 Nm).
  2. Raise and safely support the vehicle.
  3. Install the exhaust manifold heat shield. Tighten the mounting bolts to 10 ft. lbs (14 Nm).
  4. Install the exhaust manifold brace-to-manifold bolt and the oil pan nuts. Tighten the mounting bolts to 41 ft lbs (56 Nm) and the nuts to 18 ft lbs (24 Nm).
  5. Position the exhaust pipe to the manifold. Install the manifold-to-flex decoupler mounting bolts. Tighten to 26 ft lbs (35 Nm).
  6. Lower the vehicle.
  7. Coat the threads with a suitable anti-seize compound and install the O2 sensor.
  8. Connect the O2 sensor electrical connector.
  9. Connect the battery ground cable and check for leaks.
prev.gif next.gif

Sep 02, 2010 | 2000 Oldsmobile Alero

1 Answer

How do i change a water pump in a 97 grand am with a 2.4 litre engine


2.4L Engine
See Figure 3
  1. Disconnect the negative battery cable.
  2. Drain and recycle the engine coolant.
  3. Disconnect the oxygen sensor wiring.
  4. Remove the upper exhaust manifold heat shield.
  5. Raise and safely support the front end of the vehicle securely on jackstands.
  6. Remove the exhaust manifold brace bolt.
  7. Unbolt and remove the lower exhaust manifold heat shield.
  8. Break loose the manifold-to-exhaust pipe spring loaded nuts.
  9. Unbolt the radiator outlet pipe assembly from the water pump cover.
  10. Disconnect the exhaust pipe from the manifold.
  11. Pull down and back on the exhaust pipe to disengage it from the exhaust manifold bolts.
Do not rotate the flex coupling more than 4°. this could damage the component.
  1. Separate the radiator outlet pipe from the oil pan and transaxle.
    1. On manual transaxle, remove the exhaust manifold brace.

  2. Next, leave the lower radiator hose attached and pull down on the outlet pipe to detach it from the water pump. Allow the outlet pipe to hang.
  3. Lower the vehicle.
  4. Remove the exhaust manifold-to-cylinder head nuts.
  5. Extract the manifold, seals and gaskets.
  6. Remove the timing chain cover. Refer to the procedure later on in this section.
  7. Remove the timing chain tensioner. Refer to Timing Chain removal later in this section.
  8. Unbolt the water pump from the cylinder block.
  9. Extract the pump assembly-to-timing chain housing nuts.
  10. Remove the water pump and cover assembly.
  11. Separate the pump from the cover.
  12. Clean all mating surfaces of gaskets and sealant materials.

To install:
Prior to installing the water pump, read the entire procedure. Pay special attention to the tightening sequence to avoid component damage and ensure a proper seal.
  1. Attach the water pump to the cover and hand-tighten the components.
  2. Lubricate the splines of the water pump drive with chassis grease or equivalent, then install the pump and cover assembly. Hand tighten the cover-to-block bolts.
  3. Install the pump-to-chain housing nuts and hand-tighten.
  4. Lubricate the O-ring on the radiator outlet pipe with an anti-freeze solution and slide the pipe into the water pump cover, install and hand-tighten the bolts.
  5. With the specified gaps, tighten in sequence as follows:
    1. Pump assembly-to-chain housing nuts
    2. Pump cover-to-pump assembly
    3. Cover-to-block, bottom bolt first
    4. Radiator outlet pipe assembly-to-cover

  6. Install the exhaust manifold using new gaskets.
  7. Install the manifold-to-cylinder head nuts, follow the tightening sequence and tighten to specifications.
  8. Raise and support the front of the vehicle.
  9. Index the exhaust manifold-to-exhaust pipe flange bolts.
    1. Turn bolt bolts in evenly to avoid cocking the exhaust pipe and binding the bolts. Turn the bolts in until they are fully seated.

  10. Install and secure the radiator outlet pipe to the transaxle and oil pan.

On manual transaxles, install the exhaust manifold brace.
  1. Install the timing chain tensioner and chain cover.
  2. Attach the lower heat shield.
  3. Lower the vehicle.
  4. Attach the exhaust manifold brace. Tighten the manifold-to-exhaust pipe nuts to specification.
  5. Attach and secure the upper heat shield.
  6. Connect the oxygen sensor wiring.
  7. Fill the radiator with coolant water mixture until it reaches the heater hose coolant outlet, then install the hose and continue to fill. This will assist with the complete cylinder block fill.
  8. Connect the negative battery cable.
  9. Start the engine and top off the cooling system and check for leaks.
ec6ae2e.jpg

Dec 28, 2009 | 1997 Pontiac Grand Am

1 Answer

2003 oil pan removal


4.0L Engine To Remove:
  1. Disconnect negative battery cable.
  2. Lift the vehicle.
  3. Drain the engine oil.
  4. Remove or disconnect the following:
    • Exhaust pipe from exhaust manifold.
    • Exhaust hanger at the catalytic converter and lower the pipe.
    • Starter motor.
    • Flywheel/torque converter housing access cover.
    • Oil level sensor (if equipped).
  5. Place a pole jack under vibration dampener with a piece of wood between dampener and jack.
  6. Remove or disconnect the following:
    • Engine mount through bolts and raise engine for clearance to remove pan.
    • Transmission cooler lines (if equipped).
    • Oxygen sensor harness from oil pan mounting studs.
    • Oil pan bolts and studs.
    • Oil pan and gasket.
To Install:
  1. Clean the gasket mating surfaces.
  2. Apply Mopar® Silicone Adhesive Sealant or equivalent onto the cylinder block in four location as shown.
7605306.gif

  1. Attach the pan gasket to the oil pan with Hi-tack or equivalent (2003-2005 vheicles).
  2. Use 1 ½ x ¼ inch bolts to fabricate alignment dowels. Cut off the head of the bolts and cut a slot into the top of the dowels (2006 vehicles).
4e495fd.gif

  1. Install two dowels into the timing case cover (2006 vehicles).
  2. Install two dowels into the cylinder block (2006 vehicles).
  3. Place the gasket over the dowels and onto the cylinder block and timing case cover (2006 vehicles).
  4. Position the oil pan.
  5. Install the 1/4 inch oil pan bolts. Tighten to 84 in-lb (9.5 Nm).
  6. Install the 5/16 inch oil pan bolts. Tighten to 132 in-lb (15 Nm).
  7. Remove the dowels.
  8. Install the remaining 1/4 inch oil pan bolts. Tighten to 84 in-lb (9.5 Nm) (2006 vehicles).
  9. Lower the engine onto the engine mounts.
  10. Install the through bolts and tighten the nuts.
  11. Remove jack stand and remove the piece of wood.
  12. Install the flywheel and torque converter access cover.
  13. Install starter motor.
  14. Connect the exhaust pipe to the hanger and to exhaust manifold.
  15. Install the transmission oil cooling lines (if equipped).
  16. Install the oxygen sensor wiring supports to the oil pan mounting studs.
  17. Install the drain plug into the oil pan. Tighten to 25 ft-lb (34 Nm).
  18. Lower the vehicle.
  19. Connect negative battery cable.
  20. Fill the oil pan with oil. WARNING
    Use extreme caution when the engine is operating. Do not stand in a direct line with the fan. Do not put your hands near the pulleys, belts or fan. Do not wear loose clothing.
  21. Start the engine and inspect for leaks.

Jun 06, 2009 | 2003 Jeep Wrangler

2 Answers

Replace thermostat 2003 pontiac montana


yes but with the right shaped wrenches and tiny hands it can be done without removing the exhaust crossover pipe

Aug 24, 2008 | 2003 Pontiac Montana

Not finding what you are looking for?
2001 Peugeot 206 1.6 Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Wahs Team

Level 2 Expert

205 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...