Question about Cars & Trucks

1 Answer

How do you prime a clutch on a transmission of a 2004 ford edge

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Cars & Trucks Master
  • 808 Answers

For manual transmissions the master cylinder holds BRAKE fluid with a 2 ounce syringe filled with brake fluid and rubber hose on the end loosen bleeder screw on slave cylinder located on transmission near the engine squeeze the fluid into system master cylinder reservoir should start filling up this will force all air out the master tighten screw.

Posted on Apr 22, 2014

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
localwonder
  • 6784 Answers

SOURCE: 2004 ford ranger edge 3.0L spark plug wire diagram

The diagram you seek is below.


374d96b.jpg

Posted on Jul 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

2004 ford crown victoria automatic transmission overdrive lights blinking on overdrive reading codes po743 an po760


P0743 Torque Converter Clutch Circuit Electrical
P0760 Shift Solenoid C Malfunction

Sep 04, 2015 | Ford Cars & Trucks

Tip

Ford Edge Transmission Torque Mount diagnosis


Diagnosis on the Ford Edge to see if the transmission needs replacement. In this video the transmission torque mount is still in great condition after logging 134, 000 miles on this 2011 Ford Edge.
Testing the condition of the transmission torque mount on 2011 Ford Edge

on Apr 04, 2016 | Ford Cars & Trucks

2 Answers

What is the meaning of code 1744 in 2004 mercury sable


torque converter clutch stuck or not working properly

May 27, 2014 | 2004 Ford Explorer

3 Answers

Where is the TCC solenoid located


It's in the transmission. Remove the trans pan and it is on the solenoid package. But the solenoid may not be the problem. Could be the wiring, plugs(inside and outside the trans), torque converter, or the computer. 7b32d407-41bb-449c-8dd9-0a5f7effbf7f.gif

May 14, 2014 | 2004 Chevrolet TrailBlazer

1 Answer

Instructions on how to prime the clutch on a 2004 Ford Edge


If it is a hydraulic clutch then fill the reservoir and pump the clutch pedal a few times It is a two man job. pump the clutch pedal and then hold it down while your assistant opens the bleed screw on the slave cylinder.. Close the screw and re-pump the pedal Repeat the process until you have a firm clutch pedal.

Apr 22, 2014 | Cars & Trucks

1 Answer

P0701 and p0704


Unfortunately the 0700 series of numbers relate to the transmission. Code ( P0701) is pushed by 1- Open or short transmission control system circuit. 2 - Poor transmission control system electrical connection. 3 - Check powers and grounds to Transmission Control Module (TCM). Code P0704 is pushed by 1- Faulty Clutch Switch.
2 - Misadjusted Clutch Switch. 3 - Clutch Switch harness is open or shorted. 3 - Clutch Switch circuit poor electrical connection. 4 - Faulty Engine Control Module (ECM). But I'm guessing you have an automatic trans. right. If so I would look at the (DTR) digital transmission range sensor.

Nov 26, 2013 | 2004 Ford Expedition

1 Answer

Ford fusion no gears 2004


I would think the clutch disk has come apart. Do make sure the transmission linkage is connected and is switching gears under the hood..

Jul 17, 2012 | 2004 Ford Fusion

1 Answer

Just had new clutch fitted on 02 ford focus 1.6 now making noise but stops when i press clutch down


A couple of things comes to mind, when you press the clutch you disengage the transmission. When the clutch is not pressed the transmission still spins inside even when it is in neutral. Sounds like a bearing inside the transmission is making noise, did they put fluid back in the transmission? Also another common source of noise is the throw out bearing, it is on the input shaft, it is the actual part that presses against the clutch pressure plate, usually though they make noise when the clutch is pressed and quiet down when released.

May 07, 2010 | 2004 Ford Focus

3 Answers

2001 Ford ranger edge. The gears won't change.


The trans will need to come out. While your at it, just replace the clutch assembly, rear main oil seal, resurface the flywheel, and the clutch master cyl. Its not really a job you should do, find a repair shop to handle it.

Nov 06, 2009 | Ford Edge Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...