Question about 2002 Honda Civic

1 Answer

Clutch travel to the floor

Clutch pedal travels to the floor, oil is full but the car is been sitting all winter..

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Honda Master
  • 808 Answers

The brake fluid has drain out of clutch master cylinder fill with brake fluid reservoir is next to the brake master cylinder. pump pedal if spongy then bleed system with a 2 ounce syringe at slave cylinder loosen screw and force fluid to the master this will push all the air out.

Posted on Apr 22, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My clutch goes all the way to the floor I have a standard Camaro 96 3.8


clutch pedals are suposed to go all the way to the floor , you sure you dont mean brake pedal (cus thats bad ! ) clutches should travel all the way to floor and release the "grab" of the engine about 2/3 down , this way they are more smoothly allowing shifting thru the gears and not jerking as you shift thru the gears , if clutch pedal does not start to "grab" the engines power by 2/3 off the floor and fully "grab"its power all the way up(slipping) ,and you have a hydraulic clutch (96's do) then the clutch disk may require replacement or there is a oil leak in the clutch/master/slave cylinder , look for small oil leaks from under car in area of foot pedals
clutches should be replaced as an assembly that includes , disk ,pressure plate, throwout bearing , with engine side clutch plate magnafluxed for heat cracks and any hydraulic oil leaks replaced or repaired

Mar 12, 2015 | 1996 Chevrolet Camaro

2 Answers

2004 mini cooper manual trans has a noise at shifting 1st and 2nd gears


check for clutch travel and adjustment, as well as gear box oil level and correct grade, also make sure there isn't a floor matt hindering full pedal travel

Dec 04, 2014 | 2004 Mini Cooper

2 Answers

Clutch would not engage


First you must bleed the clutch fluid by pumping clutch pedal and holding down to the floor while a helper opens and closes the bleeder On the slave cylinder
If still no operation after that you probably need a clutch assy

Apr 22, 2014 | 2002 Honda Civic

1 Answer

Clutch pedal travel


Your pedal height may be adjustable by a stopper bolt at top of pedal. You would have to check the specification for your car. Most important that the pedal has about a half inch free travel before clutch begins to engage. You need that free play to ensure the release bearing (the throw-out bearing) is not touching the fingers on the pressure plate when not engaged. If it always is touching, it will be rolling around constantly and will go out prematurely.
Your new clutch will allow gear engagement sooner as the clutch pedal is released. I mean gears will engage just as pedal is lifting off from floor. You should notice that difference-the old clutch would have taken longer pedal travel from floor before releasing.

Apr 15, 2013 | Cars & Trucks

1 Answer

How do you bleed a hydraulic clutch on golf mk4


Hi Riaan, This is a two or three person job. Make sure the reservoir is full and kept full during the whole operation. open the bleeding nipple on the slave cylinder until clear fluid is seen running from the opening. Close the nipple and press the clutch pedal from the top of its travel to the floor four times and while the pedal is fully depressed open and close the bleeding nipple. Repeat until clutch pedal pressure feels correct. Make sure the reservoir is full and off you go. Regards John

Oct 17, 2012 | Volkswagen Cars & Trucks

1 Answer

Clutch pedal travel is excessive. Sits about 2"


A clutch pedal takes MUCH more travel to function correctly, when compared to a brake system...

A clutch needs to be replaced (maybe) when it SLIPS, Chatters, Or fails to release...

Other than that, the clutch will need to be adjusted to allow for total release of the relese bearing when pedal is released, and full disengaugement when pedal is depressed....Have a mechanic look at the adjustement, as proper adjustment gives longer clutch life. This is a periodic adjustment item.

Apr 03, 2011 | 2001 Subaru Impreza

2 Answers

* Clutch pedal all the way to the floor, impossible to change gears.


this problem is caused by a leaking hydraulic clutch slave or master cylinder, the most likely cause is the slave cylinder down on the transmission, have a shop put it up and see where the leaking fluid is coming from, top or bottom..

Jan 28, 2010 | 1995 BMW 5 Series

2 Answers

Clutch slipping


first i would try adjusting the clutch cable because commonly people with think that they're clutch is going out when really just the cable has gotten stretched....try adjusting that first and if that works then you should be fine for another couple thousand miles but if you want to not have to worry bout it for awhile i would just replace teh clutch assembly....usually ranges from $200 to $450 depending on the clutch set and the mechanic that does the work for you. Let me know what happens. :)

Oct 01, 2008 | 1990 Peugeot 405

2 Answers

Front wheel Drive query


DEar Customer,

your from is that your car is front wheel drive & you have to reset your car clutch point that loose its sensitivity as they had before,

its not a big prib you have to open bonet than make more active clutch wire with streching clutch joints.

THNX

May 17, 2008 | 1991 Peugeot 405

Not finding what you are looking for?
2002 Honda Civic Logo

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...