Question about 2007 Chevrolet Matiz 1.0

1 Answer

HAZARD WARNING LIGHT SWITCH DOES NOT ILLUMINATE WHEN PRESSED

HAZARD WARNING LIGHT SWITCH DOES NOT ILLUMINATE WHEN PRESSED,CHECKED ALL FUSES AND REPLACED THE SWITCH,BUT THE BULB/LED WORKS WHEN TESTED OUT OF THE SWITCH

Posted by on

  • JEDI
    JEDI Apr 24, 2014

    checked all fuses,replaced switch,the switch works but does not light up???

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 39 Answers

Sounds like a broken or lose wire.

Posted on May 28, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: I own a 2003 Chevy

I have the same issue with my 2002 Chevy Trailblazer. How did you resolve this problem?

Thanks

Posted on Jul 27, 2008

  • 5 Answers

SOURCE: checked all fuses-good, swapped bulbs-good, hazard

Does the turn signals or hazards work in the rear?? Yes... it may be the brake switch or the turn signal switch (power goes from battery, to the brake switch then to the turn signal switch, then to the lights. No? .. again.. possibly turn signal switch or the wiring between cab and bed.

Posted on Jun 04, 2009

  • 4 Answers

SOURCE: 99 Chevy Tahoe... Rear turn signals, brake lights, and hazards

I had this problem, and to be honest, it happened to the left side about a week later...it's the board that the bulbs plug into...it's a very common problem with this model. So popular that you can normally get the socket board off the shelf at a parts store! it's extremely simple to replace, and I replaced all the bulbs at the same time!

Posted on Oct 11, 2009

  • 3 Answers

SOURCE: I have a 2001 chevy hd2500 duramax 4x4. I have

check the ground on the lights.

Posted on Nov 30, 2009

oneStan
  • 430 Answers

SOURCE: Brake lights don't work. Replaced bulbs, checked

Yes, you need to of course check the voltage coming into and going out of the brake light switch, if 12 Volts are there going out and coming in while pressing on the brake pedal, your brake lights aren't getting a good ground or there is a break in the circuit between that switch & the lights.

On occasion the tail lights will work with a weak ground circuit where the Brake lights won't. Best way to determine this is to just hook up the 12 volt tester to the Brake light hot wire & there at the bulb ground, then in an area away from the bulb that has a good possibility of contact/ground.

Really that's it, if the 12Volts is getting to the bulb but it isn't lighting, if you aren't getting the voltage there and the brake switch is hot on both sides when pressed, the break in voltage will have to be traced from that switch to the tail light to find the problem.

good luck.

Posted on Feb 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn signal relay 2008 jeep location


There is no relay , controlled by integrated power module . Electronics !

Feb 12, 2016 | 2008 Jeep Grand Cherokee Laredo

1 Answer

Hazard warning switch


need a new relay,it is sticking

Apr 24, 2014 | 2007 Chevrolet Matiz 1.0

2 Answers

Turn signals and hazard lights


There is 1 other item in the system, the flasher unit. this is what makes every thing flash and is normally found near the steering column, these do fail

Dec 13, 2013 | 2001 Chevrolet Impala

1 Answer

2004 Armada. Brake lights don't work.


may have to purchase an electrical shopm manual for more information

Mar 31, 2012 | 2004 Nissan Armada

1 Answer

1992 Ford Ranger Turn signal/Hazard light issue


Can you just check to make sure the ignition key switch is not staying over to far and not backing off when you try to start it. I had a truck that did that and it messed up my turn signals until I brought the key switch back a little after starting it. Just a simple idea. Be kind with your rating for me. Raz

Apr 19, 2010 | 1992 Ford Ranger

1 Answer

2001 GMC Jimmy break lights not working but all


Check the brake light switch should be a orange wire with 12v then a white wire with 12v when the pedal is pressed.If htat cks good then ck the hazard switch by moving it up and down and wiggeling the knob with the brake pedal pressed if they start working then your multifunction switch is bad and needs to be replaced.

Feb 20, 2010 | 2001 GMC Jimmy

1 Answer

My indicators and hazard warning lights have both suddenly stopped working have checked all fuses all seem ok


I think there is an issue with turn signal switch, test the leads at the switch that are supposed to have power, if they are ok replace the switch. An inexpensive test light will do nicely for these checks.

Aug 21, 2008 | Alfa Romeo 156 Cars & Trucks

Not finding what you are looking for?
2007 Chevrolet Matiz 1.0 Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...