Question about Jeep Cherokee

1 Answer

All lights except parking lights work. How do I get all the lights to work as intended? I have replaced all bulbs and checked fuses. Pleeeeeeeeeez

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 72 Answers

What is the year & type of of Cherokee?

Posted on Jun 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Cadillac Escalade all light working after I change bulbs except one tail light. Help


Which tail light ? Does the stop light ,turn signal work ? Check fuse's LR PARK fuse 10amp or the RR PARK fuse 10amp located in the under hood fuse box .

Mar 26, 2017 | 2003 Cadillac Escalade

1 Answer

Park lights not working i have checked all the fuse


Hello XN,

Without any vehicle specifics... you are going to get
general/typical... answers.

Check all the bulbs first...
(rule: eliminate easiest/cheapest... FIRST).

Hopefully you are not talking about a CHRYSLER product...
Rather than decent serviceable relays they have an ugly expensive "total" unit...

In any case... you will need to identify you switch output... verify it works... Fails = replace... else move on to

Control relay... properly seated... Verify switch voltage at the relay
operation... Measure the Light source voltage across the relay...

Un-plug the relay and measure the filament voltage through the bulbs... If you cannot see the bulbs (resistive grounds) through the bulbs... and the bulbs, battery, relays & sockets are all good..
The it is time to beg, borrow or buy a wire tone tracer.

They work best on open wires (so remove the bulbs) and test for good body grounds first (highly unlikely).

Hope this helps!

Free wiring diagrams at bbbind.com (usa models)
Try also the FACTORY+WORKSHOP+MANUAL for electrical detail

BBB Industries Premium Alternators Starters Power Steering Products

Sep 05, 2016 | Cars & Trucks

1 Answer

Passenger rear park lamp doesn't work.


Both park lamps should be powered by the same wire, so follow wire from non-working light until you find a break or bad connector.

Mar 28, 2015 | 2004 GMC Canyon

1 Answer

The lights around my license plate are out. I replaced them and they are still not working. I am wondering about the fuse, but am not sure which fuse controls these lights on a 2000 Lincoln Town car


not sure which fuse except to say same fuse as tail lights is one you're looking for. try turning your park lights on and wiggling bulbs back and forth,i suspect a bad ground inside bulb holder. you can wiggle bulb to check that. after you do get it working i suggest you apply some bulb grease to put into bulb socket for no future problems.

Aug 19, 2010 | 2000 Lincoln Town Car

1 Answer

My brake lights won't work in my AU Ford Falcon


On vehicles that use a common bulb for signal and brake lights the brake light circuit runs through the signal switch. A problem in the signal switch can cause the brake lights not to function. Also check your Emergency flasher switch. Hope this helps.

Apr 11, 2010 | Ford F Cars & Trucks

1 Answer

2001 s10 headlights will not come on all the time


are you sure the bulbs are o.k.? if they dont work on both high and low you have ground wiring problem. ground the black wire at the plug with lights on.

Jan 29, 2009 | 2004 Ford Crown Victoria

1 Answer

Replace park lights on 1998 camry


If your dash lights work, your park light fuse is OK.

Jul 27, 2008 | 1999 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...