Question about Honda Odyssey

Open Question

P0703 neon trouble code - Odyssey Honda Cars & Trucks

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My car is a 2006 forenza it wont shift into overdrive unless i push the hold button but if you leave it on and slow down it has no power any help mine


you sound like guy that works FSM free,?
no books. why do that ,? (pain)
i guess you get scan codes. and above is wrong. P0703. is it.?
post the full codes, all of them all DTCs stored.
then look them up in the FSM and what does it says.
it tells you, to do more tests. to find true cause.

my guess, you never said
car drives prefect,
the CEL glows, or the scan tools shows MIL active.
right>?
the hold is for ice.
the hold prevents down shifts (dangerous) on ICE.

with most feature of the TCM (tranny brain) lots of failures
cross over. to shifting.
lots.
like engine overheated
engine overloaded.
engine speed,
brakes on or off.
cruise controls
traction. and ABS.
direction controls. (if present)

so stop ignoring those codes and fix what it told you to fix
fix the what is it, P0703...
???

the recall (sic) TSB TS-09-03129R
summary:Suzuki vehicles: automatic transmission shift lever is loose in the shift gate and/or ignition key cannot be removed. The transmission gear shift lever does not hold firmly to the left of the shift gage as expected.


and the 703, dont lie. it told you its fails and you ignored this fact.

http://www.aboutautomobile.com/DTC/P0703

it's bad, replace or recalibrate the switch.
and on newer cars the switch may need calibration after the replacement.
owning a Chapter 11 car company car is a PITA.

id sell it. i would and get a Toyota.



Aug 11, 2014 | 2006 Suzuki Forenza

1 Answer

Brake light switch


code p0703 refers to torque converter / brake switch B--circuit malfunction===causes--wiring--torque converter/ brake switch--ECM/TCM. The problem may not be in the brakes circuit but in the torque converter sensors.

Oct 22, 2013 | Dodge Avenger Cars & Trucks

1 Answer

Check Engine light with code P0703


About $20 for a new brake light switch that can be installed in about 15 minutes or less usually, may be good insurance for a long distance drive. The code doesn't say it's a switch malfunction, the computer has seen a fault in the brake switch circuit and set the code-could just be a poor connection there.
More important, how do the brake lights work? I think I'd buy the switch or check the connector by the pedal at least. The computer may not let the cruise control work because of the code.

Jul 14, 2012 | 2003 Dodge Neon

1 Answer

Pontic check engine code P0703


Hi the code P0703 is Brake switch B circuit malfunction. I`m not sure if this means the brake switch
is faulty or the wiring to it is faulty.
The brake switch is the best place to start ( but check the connections to the switch )
I hope i have been of help to you.
john ( South Wales UK )

Jun 30, 2011 | 1994 Chevrolet Lumina APV

1 Answer

What does P0703 brake switch circuit B mean?


sounds like you may have a bad brake light switch from the factory. Id take the one you put on and try swapping it with another one. if you have a scan tool, check and make sure the brake light switch (will probably read BOO on scan tool) reads "on" when you push it down and "off" when your foot is off of it. check voltage and ground at your connector to make sure you have a complete circuit. If it reads "on" when you disconnect the switch, replace the switch.

Jan 24, 2011 | 2003 Dodge Neon

1 Answer

Ihave code p0703 brake switch,what can I do?


P0703 (M) Brake Switch Stuck Pressed or Released Incorrect input state detected in the brake switch circuit (Changed from P1595).

The switch cost like 20 bucks. It is located on the brake pedal, it will either be in front of or behind the pedal at the top. It will have a plunger that contacts the pedal, and an electrical pig tail. usually you just twist it and pull it out kinda like a headlamp.

Hope this help (remember rated and comment this).

Mar 29, 2010 | 2000 Dodge Neon

1 Answer

My 2005 neon failed emissions. It gave me a codes 0441. What excatly does that define?


Trouble Code: P0441 (2.0L L4 VIN C Auto)
EVAP Purge Flow Monitor Fault Print this code dataprint_icon_codes.gif Number of Trips to Set Code: 2
OBD II Monitor Type: CCM Details
Indicators: MIL Details
Trouble Code Conditions:
Engine at idle speed in closed loop for 200 seconds, BARO Sensor signal less than 8,000 feet, ECT Sensor more than 160ºF, no Low Fuel, MAP Sensor signal less than 23.7" Hg, and the PCM did not detect any purge flow through the EVAP system during this test.

Possible Causes:
  • EVAP purge solenoid vacuum line loose, leaking or restricted
  • EVAP purge solenoid stuck leaking, stuck open or stuck closed
  • EVAP purge vacuum line to canister leaking or disconnected
  • EVAP canister leaking, damaged or has failed

2005 Dodge Neon - All Configurations - P0441

Nov 01, 2009 | 2005 Dodge Neon

1 Answer

2002 NEON IDELS ROUGH AND IDELS HIGH RPM.


sounds like the intake hose from throttle body is not on intake manifold properly..as for the p0700 trouble code,you need trans controller scanned for fault codes..let me know what codes are in trans controller

Mar 15, 2009 | 2002 Dodge Neon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...